NAKAYAMA PRO ES2310 Expert Level Chain Sharpener User Manual
- June 4, 2024
- NAKAYAMA PRO
Table of Contents
ES2310
ART NO: 036289
ES2310 Expert Level Chain Sharpener
- The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
- Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
- To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
Parts Description
- handpiece
- grinding disk lateral guard
- depth of grind set screw
- cutting edge angle set-up wheel
- base
- guide screw
- rotary table
- cutting angle setting wheel
- scale
- mounting screw (10a/10b)
- guide plate
- chain stop
- grinding disk
- grinding disk protective enclosure
Technical Data
| Voltage /Frequency | 230Volt/ 50Hz |
|---|---|
| Power | 230W |
| Cutting Disk dimensions | 145×3,2mm |
Safety Instruction
read the instruction manual carefully before the first use of the machine
Protect the machine from moisture. rain and dust. FOR US TO SECURE THE HIGHEST
DEGREE OF SAFETY, CONFORM TO THE FOLLOWING INSTRUCTIONS:
- Do not use the machine for unsuitable purposes.
- When using the saw-chain grinder outdoors, you should always use a weather-resistant extension cable to connect it of a minimum diameter of I.5m ra. with the splash-proof plug and socket.
- The noise level in the working area is above 85.18(A). Therefore. wear ear protection-hearing loss is imminent.
- To protect your health at a grinding job. always use a dust protection mask and protective goggles!
- Always unplug the machine before any work on the machine (clothing, grinding disk replacement, etc.)
- Take care to have the saw-chain to be ground secured as appropriate for it not to slip out.
- It is your own interest to keep your machine clean at any time and after you finish a grinding job. chock the machine for management.
- Always keep your saw-chain grinding machine clean.
- Do not use any caustic to clean the plastic pans.
- Do not use the machine and do not work on it in the proximity of inflammable liquids and vapors thereof.
- Unplug the machine any time you replace a pan or clean the machine.
- Protect the power cable from any damage the cable may be damaged by oil or acid.
- Important notice! Observe any national safety regulations regarding installation. operation and maintenance.
- Upon having completed the job. unplug the saw-chain grinding machine from the mains.
- Protect your eyes and colleagues from jumping panicle and chips.
- Working gloves will protect your fingers and skin from cutting injuries.
- Always carry the power cable to the machine from behind.
- Store the machine in a place inaccessible to children.
- Always hold the machine with both hands when working and mind safe footing and posture.
CAUTION! Abide by the essential safety measures of protection from electric shock accident and fire prevention. Read all these instructions before you get down to the use of the electric machine and follow them. Keep the safety instructions in a safe place for future reference..
Safe work
-
Keep your workplace tidy.
-
Always make allowances for the environmental effects. Do not expose the electric tools to rain. Do not use them in moist or wet areas. Take care of sufficient lighting. Do not use them in proximity to flammable liquids or gases.
-
Get protected from electrical shock. Avoid any bodily contact with grounded objects (such as pipes, radiators, stoves, and refrigerators).
-
Prevent the children from accessing.
-
Do not let another person touch the machine or the cable. Prevent any unauthorized persons from access to the working area.
-
Store the machine in a safe place. When in use, the machine should be kept in a dry, elevated locked place out of the reach of children.
-
Do not overload the machine.
-
Use the correct machine. Only use the machine for the purposes described in the instruction manual.
-
%Year proper working clothing!
Do not wear any wide garments and jewelry that might be caught by the moving machine parts, for working outdoors, rubber gloves and non-kid shoes are recommended. If your hair is long, wear a helmet. Use protective goggles -
Wear a breathing mask when engaged in a dust-producing job.
-
Do not use the cable for any purpose it has not been designated for. Do not use the cable for carrying or hanging the machine. Do not use the cable to pull out the plug from the socket. Protect the cable from excessive temperatures, oil, and sharp edges.
-
Avoid any abnormal posture. Mind safe footing and keep the balance at any time.
-
Take due care of your machine. Abide by the maintenance and grinding disk replacement regulations. Check the machine cable regularly and when it is found to be damaged, have it replaced by a skilled electrician. Check the extension cables regularly and replace them if damaged. Keep the handle dry, free of any dirt, oil, and grease.
-
Unplug the machine. if it is out of use, prior to the maintenance and tool replacement. e.g.ginding disk.
-
Remove any spanners from the machine. Before switching on, check to see that any wenches and adjustment tools were removed.
-
Avoid unintended switching. Use only permitted and properly marked extension cables for working outdoors
-
Check the machine for possible damages
-
Before using the machine, you should check any protection devices and any pans showing slight damage to see if the function intended is perfect. Check the moving parts move freely, do not drag, and are not damaged. Any parts should be installed properly to comply with the conditions of the machine’s safe operation. Damage protection device: MD pans should be repaired in a recognized professional workshop and replaced unless the instructions for use specify otherwise. The damaged switch should be replaced by the customer service workshop. Do not use a machine with a defective ON/OFFsuitch.
CAUTION!
this machine is in compliance with any respective safety provisions. Any
repairs shall be done by professionally qualified persons and only genuine
spare pans should be used. The provision is not being observed, and the
operator is in at risk of injury.
Assembly
The saw-chain grinding machine is delivered pre-assembled. One pan consists of
the base, on which the chain guide is located. The other part is a bearing arm
with the motor and handgrip. The assembly shall be performed with the machine
unplugged! The machine design provides either a desk installation or a wall
mountinr When installing it on the desk, put the machine nn the edge of the
desk and screw it to the desk using the holes in the base. When mounting on
the wall, use the respective holes in the venial pan of the base (here, a
distance from the wall should be kept or spacers should be used for the access
to the rear set screw to be preserved). After the desktop installation, lit
the arm in the base inserting the pilot pin and securing it with a hexagonal
screw ( Fig.!)
Now, it is possible to fit a washer on the rear side screw and screw the
setting and screw the setting wheel on. (Fig.2) Screw the supporting arms
control holder on the screw in the grinding disk body (Fig.3) Fit the grinding
disk enclosure in using the supplied screws and a respective wench (Fig,4).
Tip: %% hen mounting, on the wall, take care to mount the machine at a
height or 120-130cm from the floor to amid working at e height!
To be able to install the disk, it is necessary to unscrew the auxiliary
flange (Fig.5) .
Grinding Disk Assembly
After you have removed the ancillary flange, you can insert thegrinding disk
in the body from below. See that the ancillary flange and the disk abut
against each other precisely. (Fig.6). Do not tighten the screws too much to
avoid any damage to the disk. The grinding disk on the hub torque is 7Nm.
Where practicable. use a torque spanner. Now, the grinding disk additional
guard should be fitted on (Fig.?). Check the correct bottoming of the disk: in
should not moveacross and lengthwise. Now, with the grinding disk properly
installed, a trial may be performed. Stand by the machine from the side and
watch out for anybody dwelling in the working area. If the grinding disk is
vibrating or shows otherwise incorrect run, promptly switch off and unplug the
machine before you attempt clearing the fault. The machine has a -zero voltage
circuit breaker-which is disabled on the outage and will prevent any
restarting of the machine after the power supply is restored. Using the
sharpening stone and a clamping plate, it is possible to sharpen the disk to
obtain the required profile. In this case. be careful at work.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>