NAKAYAMA PRO PB6310 Cordless Brush Cutter User Manual

NAKAYAMA PRO PB6310 Cordless Brush Cutter User Manual

Before using our products. Please read this manual carefully to understand the proper use of your unit.
Keep this manual in a safe place.

Notes On Types Of Warnings In The Manual

This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.

This mark indicates instructions, which must be followed, or it leads to mechanical failure, breakdown, or damage.

This mark indicates hints or directions useful in the use of the product.

Description

1. Fuel tank
2. Starter assembly
3. Air cleaner
4. Support
5. Throttle cable
6. Handle
7. Connector assembly
8. Switch
9. Throttle lever
10. Handle bracket
11. Aluminium pipe
12. Protector
13. Gear case assembly
14. Nylon cutter
15. Metal blade

Warning Labels On The Machine

1. Read this manual carefully before operating the machine.
2. Wear head, eye and ear protection.
3. Warning / Attention.
4. Keep all children; bystanders and helpers 15 meters away from the brush cutter.

If warning stickers peel off or become impossible to read you should contact the dealer from who you purchased the product and order new stickers.

Never remodel your brush cutter. We don’t warrant the machine, if you remodelled brush cutter or you don’t observe the proper usage written in the manual.

Symbols On The Machine

For safe operation and maintenance symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.

(a) The port to refuel the “MIX GASOLINE” POSITION: FUEL TANK CAP
(b) The direction to close the choke POSITION: AIR CLEANER COVER
(c) The direction to open the choke POSITION: AIR CLEANER COVER

Safety Precautions

Before Using The Machine
a. Read this owner’s manual carefully to understand how to operate this unit properly.
b. This product has been designed for cutting the grass and it should be never used for any other purpose.
c. You should never use this brush cutler when under the influence of alcohol, when suffering from exhaustion or lack of sleep, when suffering from drowsiness as a result of having taken cold medicine, or at any other time when a possibility exists that your judgment might be impaired or that you might not be able to operate the brush cutter properly and in a safe manner.
d. Avoid running the engine indoors. The exhaust gases contain harmful carbon monoxide.
e. Never use your brush cutter under circumstances like those described below:

1.  When the ground is slippery or when other conditions exist which might make it not possible to maintain a steady posture while using this brush cutter.
2. At night, at times of heavy fog or at any other times when your field of vision might be limited and it would different to gain a clear view of area.
3. During rain storms, during light storms. Al times of strong or gale force winds, or at any other times when weather conditions might make ii unsafe to use this machine.

f. When using this machine for the first time. Before beginning actual work. Please learn to handle this brush cutter from skilled worker.
g. Lack of sleep, tiredness or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury.
Limit the amount of time over which the brush cutter is to be used continuously to somewhere around 30-40 minutes per session, and take 10-20 minutes or rest between work sessions. Also try to keep the total amount of work performed in a single day under 2 hours or less.
h. Be sure to keep this manual handy, so that you may refer to it later whenever any questions arise.
i. Always be sure to include this manual when selling, lending or otherwise transferring the ownership of this product.
j. Never allow children or anyone unable to fully understand the directions given in this manual to use this brush cutter.

Working Gear And Clothing
A. When using your brush cutter, you should wear proper clothing and protective equipment as follows:

1. Helmet
2. Protection goggles or face protector
3. Thick work gloves
4. Non-slip-sole work boots
5. Ear protectors

B. And you should carry with you the things as follows:

1. Attached tools and files
2. Properly reserved
3. Spare blade
4. Things to notify your working area(rope, warning signs)
5. Whistle (for collaboration or emergency)
6. Hatchet or saw (for removal of obstacles)

C. Never use your brush cutter when wearing parts with loose cuffs, when wearing sandals or when barefoot.

Warning Considering Handling Of Fuel

a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.
Smoking while operating the brush cutter of refilling its fuel tank is extremely dangerous. Always be sure to keep lit cigarettes away from the brush cutter at all times.
c. When refilling the tank always turn off the engine first and take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refuelling.
d. If any fluid spillage occurs during refuelling, use a dry cloth to wipe up spills before turning the engine back on again.
e. After refuelling, screw the fuel cap back tightly onto the fuel tank and then carry the brush cutter to a spot 3m or more away from where it was refuelled before turning on the engine.

Things To Check Before Using Your Hedge Trimmer

a. Before beginning work, look around carefully to get a feel for the shape of the land, or grass to be trimmed, and whether or not there arc any obstacles which might get in the way while working, and remove any obstacles which can be cleared away.
b. The area within a perimeter of 1 Sqm of the person using the brush cutter should be considered a hazardous

1. Make sure the appropriate blade cover is in place.
   When transporting by car, fix the unit firmly using a rope. Do not transport by bicycle or motorbike because it is dangerous.

2. Never transport the brush to over rough roads over long distances without first removing all fuel from the fuel tanks, as doing so might cause fuel to leak from the tank.

Operation Safety Precautions

1. Grip the handles of the brush cutter firmly with both hands. If you suspend the work, place the throttle to the idling position.

2. Always be sure to maintain a steady even posture while working.

3. Maintain the speed of the engine at the level requires to perform cutting work, and never raise the speed of the engine above the level necessary.

4. If the grass gets caught in the blade during operation, or if you need to check the unit or refuel the tank, always be sure to turn off the engine.

5. If the blade touches a hard object like a stone,immediately stop the engine and check if something is wrong with the blade.
   If so, replace the blade by new one.

6. If someone calls out while working, always be sure to turn off the engine before turning around.

7. Never touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an electrical shock.

8. Never touch the muffler, spark plug or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. Do so may result in serous bums

9. When you finish cutting in one location and wish to continue work in another spot, turn off the engine and turn the unit as the blade face away from your body.

Maintenance Safety Precaution

a. Perform the maintenance and checking operations described in this manual at regular interval. If any parts must be replaced or any maintenance of repair work not described in this manual must be performed, please contact a representative from the nearest authorized servicing dealer for assistance.
b. Under no circumstances should you never take apart the brush cutler or after it in any way. Doing so might result in the brush cutter becoming damaged during operation or the brush cutter becoming unable lo operate properly.
c. Always be sure to turn off the engine before performing any maintenance or checking procedure.
d. When sharpening, removing, or reattaching the blade proper tools and equipment to prevent injury.
e. When replacing the blade or any other parts or when replacing the oil or any lubricants, always be sure to use only products or products which have been certified by for use with the brush cutter.

Set Up

Engine And Main Parts
Align the hanger and the fuel tank using attached 4 bolts secure the connection firmly with equal force. (F1)

1. Fuel tank
2. Bolt
3. Main pipe

Handle

1. Loosen the 4 bolts on the handle bracket. (F2)
2. Insert the right handle (throttle lever is attached) and the left handle assembly into the bracket and tighten the bolts securely. (F2)
   (1)Handle bracket, (2)Right handle, (3)Bolt, (4)Left handle, (5)Engine side.

Safety Guard
Attach the safety guard to the gear case and fix it with the clamp and 2 bolts M5x25 securely (F3).

(1) Bolt (2) Clamp
(3) Main pipe (4) Safety guard

Throttle Wire

After fitting up the wire, make sure that the throttle cable is put in the throttle lever . If not, it is very dangerous because the engines rotate after releasing the throttle.

1. Hook the cable and into the hole of the throttle lever. And set the cable in the lever as shown in the picture.
2. Wrap the band so as the throttle wire is fixed with the handle. (1) Hole (2) Throttle cable

Adjusting The Throttle Cable

1. After the throttle lever, pull the throttle wire. The normal play is 1 or 2mm when measured at the carburettor side end.
2. If the play is short or long, take off the air cleaner cover, loosen the lock nut and adjust the play. (F5)
   (1) Adjust nut
   (2) Lock nut

Installing The Metal Blade (F6)

1. Set the inner holder to the gear shaft and turn to fix with the attached L-shaped bar.
2. Put the blade on the inner holder with letters to the gear case, and match correctly the hole of the blade to the projection of the inner holder.
3. Set the outer holder to the gear shaft with the hollowed face to the blade.
4. Put the attached bolt cover on the outer holder and secure it with the bolt(Left screw) together with the spring washer and the washer.
   (1) Nut
   (2) Spring washer
   (3) Washer
   (4) Outer holder
   (5) Blade
   (6) Gear shaft
   (7) Bar
   (8) Inner holder
   (9) Gear case

Installing The Nylon Cutter (Optional) (F7)

1. Set correctly the inner holder and the outer holder to the gear shaft.
2. Screws the attached bolt(M8 left) into the gear shaft and secure it with the
3. Screw the nylon cutter into the bolt by fixing the inner holder with the L-shaped bar and tighten it manually.

Keep bolts and washers to install the blade carefully so as to lose them

1. Gear case
2. Bolt
3. Nylon head
4. Nylon cord

Fuel

• Gasoline is very flammable. Avoid-smoking or bringing any flame or sparks near

•  Wipe up all spills before starting the engine.

• Make sure to stop the engine and allow it cool before refuelling the unit.

• Keep open flames away from the area where fuel is handled or stored.

• Never use oil for 4 cycle engine or water cooled 2 cycle engine. It could cause spark plug fouling, exhaust port blocking or piston ring sticking.

• Mixed fuels which have been left unused for a period of one month or more may clog the carburettor or result in the engine failing to operate properly. Put remaining fuel into an air-tight container and keep it in the dark and cool room.
  Mix a regular grade gasoline(leaded or unleaded, alcohol-free) and a quality proven motor oil for air cooled 2 cycle engines.

 Recommended mixing ratio: gasoline 25:oil 1

Operation

Starting The Engine

Before starting the engine, inspect the entire unit for loose fillings or duel and the cutting attachments is properly installed and securely fastened.
Place the unit on a flat, firm place. Keep the cutting head clear of everything around it.

1. Turn the cap to the fuel tank to make sure that it is fixed on tightly.(F8)
   (1) Cap
   (2) Fuel tank

2. Open the fuel tank cock. (F9)

3. Move the choke lever to the closed position. (F9)
   (1) Choke lever
   (2) Fuel cock
   (3) Close
   (4) Open
   (5) Close
   (6) Open

When restarting immediately after stopping the engine, move the choke lever to the open position.

4. Set the throttle lever to the starting position. (F10)
   (1) Idling
   (2) Starting( l/3~1/2 open)
   (3) Full throttle
   When restarting immediately after stopping the engine, move the throttle to the idling position.

5. While holding the unit firmly, pull out the starter rope quickly. (F11)

6. After the engine has started, open the choke gradually.

7. Allow the engine to run for 2 to 3 minutes to warm up.

Stopping The Engine

1. Return the throttle lever to the idling position.
2. Push the engine switch button.

Equipping The Shoulder Band (F12)

1. Equip the attached shoulder band.
2. Turn on the engine, return the throttle lever to the lowest speed position, and Put the shawl band hook to the hanging pan of the machine ..
3. Adjust the length of the shawl band so that the blade may be parallel to the ground in the working position. In order to prevent slack during operation, turn up the extra pan of the band from the buckle.

Cutting Operation
Metal Blade Usage

• Always cut by guiding the head from your right to left.
• A .metal blade cut best up to the point 1/3 from the edge. Use that area for shrubs, tough and thick weeds. For cutting young grass, you can use up to 2/3 from the lip of blade.
• Adjust the engine speed according to the cutting objects. Cut the young grass at middle speed, and cut shrubs or tough and thick weeds at high speed.
  (1) For branches and trees
  (2) For grass and weeds
  (3) Direction of cutting
  (4) Direction of rotation
  Important: Operating at low speed makes it easier for grass, weeds, or twigs to become caught up in the blades, and also it makes the shaft and clutch wear down more quickly.

Nylon Cutter Usage

• Nylon cord consumes large power. Please note that the engine rotation speed in operation should be 50% as large as when using metal blade.
• Nylon cutter cuts grass with the power of cord rotation. If you try to cut grass for the length of cord at one time, rotation speed becomes lower due to resistance and you can’t cut well. In ease of large resistance, get the nylon cutter away from grass once, make the rotation speed higher, and cut a small amount of grass at one time.
• If you try to cut grass by swinging the brush cutter in the reverse way(from left to right), scraps fly in the direction away from the body. You can avoid getting your clothes dirty

Maintenance

Blade
Sharpen each cutting edge and make sure the bottom comer is rounded.
Do not cool the blade with water in case of using grinder. It may cause cracks on blade.

After 25 Hours of use
Air Cleaner
Check and clean the filter element in warm soapy water as required. Dry completely before installing. If the clement is broken or shrunk, replace with a new one. (F14)
(1) Cover
(2) Element
(3) Screen
(4) Body

Important

• A clogged air filter may increase fuel consumption while cutting down the engine power.
• And operate the brush cutler without the air filter or with a clogged filter element will quickly ruin the engine.

Fuel Filter
Take the filter out of the fuelling port using a small wire hook. Disconnect the tiller assembly from the fuel pipe and unhook the retainer to disassemble it. Clean the components with gasoline.

Important
A clogged fuel filler may cause poor acceleration or the engine.

Spark Plug
Remove and inspect the spark plug and clean the electrodes as necessary with Brush.
The spark plug gap should be adjusted to 0.6-0. 7mm. (F15)

Gear Case
Supply multi-purpose grease at every 25 hours of use. Remove the cutter holders to arrange for old grease to exit. (F16)

Technical Data

Displacement: 62cc
Horsepower: 3Hp

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warran-ty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

DISPOSE OF PACKING RESPONSIBLY

DO NOT DISPOSE OF ELECTRICAL GOODS IN HOUSEHOLD WASTE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>