NAKAYAMA PRO NP1190 Inox Well Pump with Table Instruction Manual

NAKAYAMA PRO NP1190 Inox Well Pump with Table

Product Information

The NP1190 is a water pump manufactured by Nikolaou Tools. It has a voltage and frequency of 230V/50Hz and an input power of900W. The pump can deliver water up to a maximum height of 60m and has a maximum pump rate of 4500 L/h. It comes with a 20m cable length and 9 impellers. The pump is designed for efficient transmission of water and has specifications to ensure safe usage.

Product Usage Instructions

Before Operation: Ensure that the pump is in good condition before use. Do not attempt to repair the device ifit is damaged or if there is any external damage to the power cord or plug. This can lead to electrical shock.

After Turning Off the Device: Before attempting to repair the device, ensure that it is turned off and the plug isremoved from the socket. Electrical problems must only be repaired by authorized repair personnel to avoid damage and  minimize therisk of electrocution.

Troubleshooting: If the pump is running but notdelivering water, check if the water level is too low or if the pump inlet is blocked. If the pump does not start running or stops suddenly during operation, it could be due to power interruption, capacitor damage, or foreign matter stuck in the inlet. Inefficient transmission efficiency could be due to a blocked inlet area or incorrect selection of water pipes. Refer to the technical parameters for the maximum transmission height and select water pipes of other diameter or length if necessary.

Cleaning: To maintain the pump’s efficiency, clean the inlet area regularly. Close the pump, remove the powerplug, and clean the inlet to remove any foreign matter.

Storage and Transportation: Store the pump in a safe and dry place to avoid damage. During transportation, ensurethat the pump is delivered in solid packaging to avoid damages.

Environmental Disposal: The pump and its accessories are made of recyclable materials and can be disposed of accordingly. The plastics components are marked according to their material for easy removal and disposal. In observance of European Directive 2002/96/EC on waste electrical and electronic equipment, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

SAFETY INSTRUCTIONS

Note: After opening the package, please ensure that no parts are missing or damaged. If parts are missing or damaged, do not use the machine and send it back to your dealer.
Important: This manual must always accompany the equipment upon its resale.

• To ensure proper and safe operation of this equipment, the operator must read and understand these instructions before first use.
• This manual should be kept close in a safe spot and be made available to all operators of this machine.
• All electrical sockets must be earthed.
• No power cord should be used for transporting or fixing the equipment.
• Don’t pull the power cord on the sharp edge and don’t press the power cord.
• Inappropriate cable extension can be dangerous. When working with this tool outdoors, use only extension cables that are approved for outdoor use.
• The power supply voltage must be the same as the voltage given on the model board.
• To avoid hazards, all installation and replacement of components can only be carried out by authorized customer service personnel.
• Electrical connections can only be performed by electrical professionals, and please comply with state regulations for this.
• This equipment must not be used by people with limited body ability, weak sensory ability, poor understanding, lack of experience or knowledge, unless they are supervised by properly trained operators or are able to understand the trained operator’s instructions on how to operate the equipment and understand its possible risk.
• For safety reasons, in principle we recommend using the device through a faulty current protection switch.
• Pay attention to the protection device.
• Check the connection of the plug before running. If the wire is damaged, it must be replaced by the manufacturer, the agent or the relevant technical personnel to avoid any danger.
• The device is suitable for children at eight or older. People with sensory or physical disabilities or deficiencies are required to use under supervision or knowledge of safety, use and danger. Children are not allowed to wash or maintain equipment without supervision.
• Do not use pumps when there is someone in the water.
• When cleaning and maintaining, please disconnect the water pump from the main power supply.
• Please contact technical staff in case of equipment damage.
• Connectors for power plugs and extension cables must be made sure that they are watertight and must not be placed in the water. Furthermore, connectors cannot be placed on the ground. It is recommended to ensure that the outlet is at least 60 mm from the ground.

Failure to follow these safety instructions can lead to injury and death.
Do not repair the power cord if there is any external damage to the power cord or plug. Danger of electrical shock.

Preconditions for smooth and proper operation
In order to ensure that the equipment is running smoothly, the following conditions must be satisfied:

• The sink is no less than square sized in 105mm*105mm or circle with 105mm in diameter.
• The water level is no less than 280mm so that the pump can draw water.

SPECIFICATIONS

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

BEFORE OPERATION

• The rope is worn through a sling of the pump.
• Screw the pipes to the pump and use the rope to draw water.
• The manual control mode must be monitored for the pump.
  Attention: Dry running leads to pump damage.

AFTER TURNING OFF THE DEVICE

• When pumping water, the water level must not be lower than 280mm. If it is, the water level is lower than impeller which leads to failure in drawing water. Stop the pump and pull up the power cord plug.
• Turn off the pump and remove the plug from the outlet.

TROUBLESHOOTING

The equipment does not need maintenance.
Before any attempt to repair the device, ensure that the device is turned off and that the plug is removed from the socket.
Attention: To avoid damage and to minimize the risk of electrocution, electrical problems must only be repaired by authorized repair personnel.

2. The pump inlet is blocked.

| 1. Check the water inlet.

2.Close the pump, remove the power and clean the inlet.

The pump does not start running or stops suddenly during operation.

| ****

1. Power interruption.

2. Capacitor damage.

3. The motor’s thermal protector switch activates and turns off the pump due to overheating of the motor.

4. There is foreign matter stuck in the inlet.

| 1. Examine the protection device and electrical connection.

2. Replace the capacitor.

3. Turn off the pump and remove the plug to cool the pump and prevent no-load operation.

4. Close the pump, remove the power plug and remove the foreign matter.

Transmission efficiency drops.| ****

1. The inlet area is blocked.

| 1. Close the pump, remove the power plug and clean the inlet.

Inefficient transmission efficiency.

| ****

1. The transmission efficiency of the pump depends on the transmission height, the pipe diameter and the height of the water pipe.

| 1. Pay attention to the maximum transmission height and refer to technical parameters. If necessary, select water pipes of other diameter or length.

CLEANING

Deposited dirt may cause difficulty or failure in the pumping tip and drainage, therefore the pump shall be cleaned regularly.

• Remove the plug from the socket.
• Raise the water pump from the water.
• Use clean water to flush the filter, baseplate and pump.

STORAGE
In order to avoid accidents and injuries, the storage area must be able to support the weight of the equipment.

1. In the equipment’s storage area, the cable and main body must not be under pressure.

2. Completely empty the equipment of water and foreign matter before storage.
   Attention: Frost will damage the equipment that is not completely empty.

3. The storage area must be protected from frost.

TRANSPORTATION

Transportation by vehicle

• Ensure that the equipment doesn’t slide, gets pressed or damaged in any way.
• To avoid accidents and injuries, ensure that the vehicle can support the weight of the equipment.

ENVIRONMENTAL DISPOSAL

In order to avoid damages on transportation, the tool has to be delivered in solid packaging. Packaging as well as the unit and accessories are made of recyclable materials and can be disposed accordingly. The tool’s plastics components are marked according to their material, which makes it possible to remove environmental friendly and differentiated because of available collection facilities.

Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

Warranty

The power tools have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards. The power tools of our company are provided with a warranty period of 24 months for non-professional use, 12 months for professional use and 12 months for batteries and chargers. The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the tool (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transportation (to and from) is enterely borne by the sender (client). The tools must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.

WARRANTY EXEMPTIONS AND RESTRICTIONS:

1. Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chokes etc.).
2. Tools damaged as a result of non-compliance with the instructions of the manufacturer.
3. Tools poorly maintained.
4. Use of improper lubricants or accessories.
5. Tools given to third entites free of charge.
6. Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
7. Connection to a non-earthed power supply.
8. Change in current voltage.
9. Damage resulting from the use of salty water (e.g., washing machines, pumps).
10. Damage or malfunction resulting from improper cleaning procedure of the tool.
11. Contact of the tool with chemicals, or damage as a result of moisture or corrosion.
12. Tools that have been modifi ed or opened by unauthorized personnel.
13. Tools used for rent.

The warranty covers only the free of charge replacement of the component that presents a manufacturing defect or material failure. In case of lack of a specifi c spare part the company reserves the right to replace the tool with another corresponding model. Ater all warranty procedures have been concluded, the warranty period of the tool shall not be extended or renewed. The spare parts or tools that are replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding power tools repair or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.

This appliance is a quality product. It was designed in compliance with current technical standards and made carefully using normal, good quality materials. The warranty period is 24 months for non-professional use and 12 months for professional use and commences on the date of purchase, which can be verifi ed by the receipt, invoice or delivery note. During this warranty period all functional errors, which, despite the careful treatment described in our operating manual, are verifi ably due to material fl aws, will be rec fi ed by our after-sales service staff . The warranty takes the form that defective parts will be repaired or replaced with perfect parts free of charge at our discretion. Replaced parts will become our property. Repair work or the replacement of individual parts will not extend the warranty period not will it result in a new warranty period being commenced for the appliance. No separate warranty period will commence for spare parts that may be ted. We cannot off er a warranty for damage and defects on appliances or their parts caused by the use of excessive force, im-proper treatment and servicing. This also applies for failures to comply with the operating manual and the installattion or spare and accessory parts that are not included in our range of products. In the event of interference with of modifications to the appliance by unauthorized persons, the warranty will be rendered void. Damages that are attributable to improper handling, over loading, or natural wear and tear are excluded from the guarantee. Damages caused by the manufacturer or by a material defect will be corrected at no charge by repair or by providing spare parts. The prerequisite is that the equipment is handed over assembled, and complete with the proof of sale and guarantee. For a guar-antee claim, only use the original packaging. That way, we can guarantee quick and smooth guarantee processing. Please send us the appliances post-paid or request a Freeway sticker. Unfortunately we will be unable to accept appliances that are not postpaid. The warranty does not cover parts that are subject to nat-ural wear and tear. If you wish to make a warranty claim, report faults or order spare parts or accessories, please contact the after-sales center: Subject to change without prior notice.

• WWW.NIKOLAOUTOOLS.GR

References

• NIKOLAOU TOOLS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>