novostella NTF71-RGBCW-US-4 Solar Spot Lights User Guide
- June 6, 2024
- novostella
Table of Contents
Solar Spot Lights User Guide
Contact Us
Have some issues? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
we are social. Get connected!
@Novostella_US @novostella_lighting @novostella_official fb.com/novostella.fans @Novostella_official
Solar Spot Lights User Guide
THANK YOU for choosing Novostella. To optimize user experience, please install and use the light according to the following instruction.
warning
(1) Please check if the light and the parts are intact before installation, if
they are damaged, please stop using them.
(2) Please press the switch on the back of the light to the “ON” mode to make
sure the light works at night.
(3) The solar spotlights come with a Light Control Function, which means that
they will automatically light up in the darkness, and shut off during the
daytime.
(4) Please install the lights in a place where allows the lights to get fully
exposed to sunlight to complete the charging process.
(5) Please plug it vertically into the soft ground to avoid any damage to the
lights.
(6) The farthest distance for the mobile phone APP to control the RGB lights
is no more than 32ft(10m), to control the light efficiently please make sure
that all lights are within 32 ft of your phone.
(7) Phone APP can control up to 6pcs RGB lights at the same time, you are able
to preset the colors and modes according to your preference.
Specification
| P/N | NTG02-CW-F-2 | NTG02-CW-F-4 | NTG02-RGB-F-2 | NTG02-RGB-F-4 |
|---|---|---|---|---|
| Quantity | 2-pack | 4-pack | 2-pack | 4-pack |
| Model | NTG02-CW | NTG02-RGB | ||
| Color | Warm White+Cool White | RGB | ||
| Controlled By | IR remote control | Phone App | ||
| Protection Rating | IP65 | |||
| Power | built-in 1500mAh battery (Solar charging) | |||
| Remote Control Distance | Max. 10m | |||
| Life Span | 30000H | |||
| Working Temperature | -20°C-40°C |
Dimension
Install
Control Methods
Type B: for NTG02-RGB
Phone APP Control Methods
Support: Bluetooth 4.0 above
Phone Support: ios 11 or above and android
4.4 or above.
Language support: English
APP name: LotuslanternX
http://www.easytrack.net.cn/download/
|
---|---
Choose lighting colors on the color wheel and adjust brightness by dragging the slider bar below.
Lights will be connected automatically to the APP when the Bluetooth function is activated on your phone.
Enter shake mode by clicking the “Setting” button.
Step Two: Enter “Mode” for lighting modes and speed settings.
Step Three: Enter the “Music” setting to play your favorite music, and
lighting will dance with the music.
Step Four : Enter the “Microphone” setting, to choose a built-in Mic, which uses the microphone function on your phone to receive audio and change lighting colors accordingly. (These lights come without an external Mic, this feature is useless, please ignore it.) Step Five: Enter “Timer” for lighting schedule setting;
If the Bluetooth connection is not successful, check the possible causes by
following the steps below.
( 1) Please make sure to press the switch on the back of the light to the “ON”
state.
(2) Please make sure that your phone’s Bluetooth is turned on.
(3) Please make sure the lights are within 32ft(10m) coverage of the mobile
phone.
(4) Please check whether the light can light up normally at night, if not, the
battery may be out of power, please charge the light under the sun until it
can be used normally.
(5) This lighting kit adopts the Bluetooth 4.0 version, which only supports
connection with one phone. Check if the lighting kit has been paired to a
phone. If yes, please disconnect it from the previous phone and pair it with
yours.
(6) Check if the Bluetooth is successfully paired to the lighting kit. If not,
exit the APP and restart it to connect the lighting kit again.
(7) If the Bluetooth connection still fails after restarting the APP, please
exit the APP and reboot your phone.
(8) Please note that the mobile APP can connect up to 6pcs of lights at the
same time.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment
should be installed and operated with a minimum distance between 20cm of the
radiator your body: Use only the supplied antenna.
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>