Trust AWST-9000Z Wireless Wall Switch User Manual

: June 9, 2024
: Trust

Table of Contents

Trust AWST-9000Z Wireless Wall Switch
OVERVIEW
BATTERY INSTALLATION
MOUNTING
Optional
Safety Instructions
Declaration of Conformity
TECHNICAL SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Trust AWST-9000Z Wireless Wall Switch

Trust-AWST-9000Z-Wireless-Wall-Switch-PRODUCT

OVERVIEW

BATTERY INSTALLATION

LED INDICATORS

MOUNTING

Trust-AWST-9000Z-Wireless-Wall-Switch-FIG
2

Optional

Trust-AWST-9000Z-Wireless-Wall-Switch-FIG
4

Insert/replace the battery
- A Remove the back plate with a flat screwdriver by placing it at the bottom between the back and front plate of the wall switch
- B Place a CR2032 battery in the wall switch
- C Put the wall switch back on the back plate. Make sure that the arrows on the back plate and in the wall switch both point up.
Send ON-OFF signal
- A Press the ON button on the wall switch 1x shortly to send an ON signal. The LED on the switch flashes 1x green.
- B Press the OFF button on the wall switch 1x shortly to send an OFF signal. The LED on the switch flashes 2x red.
Pair a Trust Smart Home receiver
- A Activate the learning mode of the receiver (Consult the receivers manual on how to put it into the learning mode).
- B When the learning mode is active, give an ON signal by pressing the ON button on the wall switch once to pair it to the receiver. The LED on the wall switch flashes 1x green.
Mount the wall switch
- A Mount the wall switch with double-sided tape
  If you want to mount the wall switch using the supplied double-sided tape, apply the double-sided tape to the back plate of the wall switch.
  Place the wall switch (with the LED on the top) at the desired location on a flat surface.
- B Mount the wall switch with screws
  If you want to mount the wall switch using the supplied screws, first remove the back plate from the wall switch (see chapter 1 step A ) and screw it tightly to the desired location.
  When mounting, the arrow on the back plate must point upwards. Then click the wall switch back on the back plate.
  When mounting on a wall box, make sure it is placed at an even height with the wall and that the back plate is hand-tightened to prevent bending of the back plate.
Set the switch-off time
With the AWST-9000 it is possible to set a Turn-off timer. With this, the wall switch switches off the paired receiver after a set time.
- A To set the Turn-off timer, press and hold the ON and OFF buttons simultaneously for 3 seconds until the LED starts flashing green
- B Give an ON signal within 3 sec to extend the Turn-off timer and an OFF signal to shorten the Turn-off time. The LED indicates which switch-off time is selected.
- 0s – LED keeps flashing 1x (no turn-off time)
- 5s – LED keeps flashing 2x
- 1m – LED keeps flashing 3x
- 10m – LED keeps flashing 4x
- 30m – LED keeps flashing 5x
- 60m – LED keeps flashing 6x

After choosing the desired Turn-off time, press and hold the ON and OFF button simultaneously again for 3 seconds, until the LED flashes quickly to confirm the setting.

Optional: Adjust the dimming range

A Press the ON button to turn on the receiver.
B Press the ON button again to activate the dimming mode. The light will dim slowly in a cycle from high brightness to low brightness.
C Press the ON key for the third time to lock the desired brightness.

Only with the ACC-250-LD and ACM-250-LD it is possible to dim the receivers by holding down the ON button to increase the brightness or holding down the OFF button to decrease the brightness.
Press the ON button twice quickly to immediately set a dimmer to 100% brightness.
Press the OFF button twice quickly to immediately switch a dimmer to the lowest brightness.

Optional: Create a double wall switch
To turn the AWST-9000 into a double wall switch, carefully remove the button with a flat screwdriver.
Click the supplied push buttons for a double wall switch on the AWST-9000.
The two push buttons can be used as two separate channels to switch lamps / devices.

Optional: Unpair a Trust Smart Home receiver
Put the receiver in the learning mode (see the manual of the receiver for information on how to activate the learning mode).
When the receiver is in learning mode, send an OFF signal with the wall switch. The LED on the wall switch flashes 2x red.

Safety Instructions

Product support: www.trust.com/71963. Warranty conditions: www.trust.com/warranty
To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety
The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete Never use Trust Smart Home products for life-support systems. This product is not water-resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: -15.73 dBm. Radio transmission frequency range: 433,92 MHz
Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.
Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.
Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.
Trust Electronics Ltd. declares that item number 71963/71963-02 is in compliance with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text of the declaration of conformity is available at the following internet address: www.trust.com/compliance
Trust International B.V. declares that item number 71963/71963-02 is in compliance with Directive 2014/53/EU –2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:

Model: AWST-9000Z WIRELESS WALL SWITCH
Item number: 71963/71963-02
Intended use: Indoor

is in compliance with the essential requirements and other relevant provisions of the following directives:
ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)
The full text of the EU declaration of conformity is available at the following web address: www.trust.com/compliance

TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com

Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change without prior notice. Made in China.