UNITECK CO00112 Pushpit Mounting Bracket Instruction Manual
- June 14, 2024
- UNITECK
Table of Contents
UNITECK CO00112 Pushpit Mounting Bracket
Dear customer, thank you for purchasing one of our Uniteck products. Please read all the instructions carefully and thoroughly before using the product.
DESCRIPTION
Unifix 20.1 WB brackets have been specially designed to fix your Unisun
10.12M/ 10.24M / 20.12M / 20.24M photovoltaic panels.
They can be installed on all pushpits or handrails with tubes from 20 to 28 mm
in diameter (minimum tube length: 150 mm).
Thanks to their structure and marine stainless steel screws and bolts, they
are perfectly suited for use in saline environments.
Equipped with a multi-position tilting system, Unifix brackets allows an
optimization of your panel’s performance depending on the chosen orientation.
Electrical performance depending on tilt and panel orientation
|
0°
| 30°| 60°| 90°|
East| 93%| 90%| 78%| 55%
South east| 93%| 96%| 88%| 66%
South| 93%| 100%| 91%| 68%
South west| 93%| 96%| 88%| 66%
West| 93%| 90%| 78%| 55%
To connect the panel / regulator / battery, we recommend that you use the Uniconnect 1.6 ready-to-use kit that optimizes your electrical performance and simplifies installation (kit for connecting 1 panel)
- The arrangement of the sensors influences your electrical performance. Choose the optimum tilt and orientation according to your environment. Avoid shaded areas or objects that may cause shadows.
- For more energy, it is possible to use two solar systems:
- panels with the same orientation: installation in parallel (two panels + one regulator + one wiring kit + branch connectors)
- panels with opposite orientations: two separate installations (one panel + one controller + wiring kit) x2Electrical
UNIFIX 20.1 WB
PANEL COMPATIBILITY
Unfix 20.1 WB can fix 1 panel with 4 holes in the frame at the spacing as
below:
RECOMMENDATIONS
Mount Unifix brackets only on surfaces with sufficient bearing capacity.
Consider the additional load with the panel:
Support| Panel|
---|---|---
Unifix 20.1 WB = 1,3 kg| Unisun 10.12M /10.24M / 20.12M / 20.24M| =1.3kg
/1,3kg/ 2kg / 2kg
Before attaching and connecting, please observe:
- the maximum distances between each element shown below.
- connecting order
SAFETY INSTRUCTIONS
- Take the appropriate mesures to prevent accidents during your mounting steps.
- If the bracket and the mounting tools are exposed to sunlight for a long period, there is a risk of getting burnt. Make sure to protect yourself accordingly.
- When finished, check and ensure that all of your brackets and panels are properly fixed.
WARRANTY
The warranty covers any defect, manufacturing flaws for 1 year from the date of its purchase (Pieces and workforce).
Warranty does not cover:
- normal wear of parts
- faulty mounting of bracket
In case of failure, return the product to your distributor by attaching:
- the dated proof of purchase (receipt, bill…)
- explanatory note of the failure
Caution : Our after-sales service does not accept carriage forward/
collected returns.
After the warranty, our after-sales service ensures repairs after acceptance
of a quotation.
After-sales service contact :
Uniteck- 1 Avenue de Rome
Zae Via Europa – bâtiment Cassis
34350 Vendres -France
E-mail : sav@uniteck.fr
Fax : +33 (0)4 88 04 72 20
INSTALLATION
Provided elements
Recommended Tightening torque
Screw | torque |
---|---|
M5 | 5,10 Nm |
M 6 | 8,80 Nm |
M 8 | 21,50 Nm |
M 10 | 44,00 Nm |
Nb. Average friction coefficient μ=0,20 / Tightening at 50% of the elastic limit.
Fixing your solar panel.
To avoid the phenomenon of galvanic corrosion, position the isolating piece
between the frame of the solar panel of anodized aluminium and the stainless
steel bracket
When you have chosen the inclination, position the locking pin to block the
rotation of the Unifix.
Please ensure that your panel and your mount are properly fixed.