SMARTAVI SM-DPN-4D Dual Head 4 Port Display Port KVM Switch User Guide
- June 14, 2024
- SmartAVI
Table of Contents
SMARTAVI SM-DPN-4D Dual Head 4 Port Display Port KVM Switch User Guide
NOTICE
The information contained in this document is subject to change without
notice. SMART-AVI makes no warranty of any kind with regard to this material,
including but not limited to, implied warranties of merchantability and
fitness for particular purpose. SMART-AVI will not be liable for errors
contained herein or for incidental or consequential damages in connection with
the furnishing, performance or use of this material. No part of this document
may be photocopied, reproduced, or translated into another language without
prior written consent from SMART-AVI, Inc.
EDID LEARN
The KVM is designed to learn a connected monitor’s EDID upon power up. In the event of connecting a new monitor to the KVM, power re-cycle is required.
SYSTEM CONTROL
There are three ways to control the SM-DPN: Keyboard Hot Keys, RS-232 Serial
Commands, and Front Panel Buttons. The settings for the serial connection are
as
follows: Baud rate: 115200 ; Data Bits: 8 ;
Parity: None; Stop Bits: 1;
Flow Control: None.
The following commands can be used:
| Command | HotKey | RS-232 |
|---|---|---|
| Switch KVM | [CT][CT][#] |
// m [#] |
| Audio Only | [CT][CT] a [#] |
// a [#] |
| KM Only | [CT][CT] c [#] |
// c [#] |
| USB Only | [CT][CT] u [#] |
// u [#] |
| Learn EDID | [CT][CT] e |
// e |
| SW Reset | [CT][CT] r | // r |
| Status Query | N/A | // ?? |
| Current HK Trigger | [Alt][Alt][Alt] x 0 |
// hk |
| Update HK Trigger | [HK][HK] x [1 | 2 |
Chart Key
[CT] = Ctrl
= Carriage Return (Enter Key)
[HK] = Current Hot Key Trigger
1 = Ctrl (Default) | 2 = Shift | 3 = Scroll Lock
HARDWARE INSTALLATION
- Ensure that power is turned off or disconnected from the unit and the computers.
- Use DP cables to connect the DP output ports from each computer to the corresponding DP IN ports of the unit.
- Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective USB ports of the unit.
- Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of the computers to the AUDIO IN ports of the unit.
- Connect monitors to the DP OUT console ports of the unit using DP cables.
- Connect a USB keyboard and mouse in the two USB console ports.
- Optionally connect stereo speakers to the AUDIO OUT port of the unit.
- Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and then turn on all the computers.
Note: You can connect up to 4 computers to the 4 port KVM.
WHAT’S IN THE BOX
PART NO. QTY DESCRIPTION
SM-DPN-4D-S| 1| Dual Head 4-Port DisplayPort KVM Switch with Audio and USB 2.0
Suppor
PS12VDC2A| 1| 12V DC, 2A power adapter with center-pin positive polarity.
| 1| Quick Start Guide
TECHNICAL SPECIFICATIONS
VIDEO
Format| DisplayPort
Maximum Pixel Clock| 165 MHz
Input Interface| (8) DisplayPort
Output Interface| (2) DisplayPort
Resolution| 3840 x 2160 @ 30 Hz
DDC| 5 volts p-p (TTL)
Input Equalization| Automatic
Input Cable Length| Up to 20 ft.
Output Cable Length| Up to 20 ft.
USB|
Signal Type| USB 2.0, 1.1, and 1.0 w/ internal hub
Input Interface| (4) USB Type B
Output Interface| (2) USB 1.1 Type A for KVM Devices(2) USB 2.0 Type A
Transparent
AUDIO
Input| (4) 3.5 mm Stereo Audio
Output| (1) 3.5 mm Stereo Audio
POWER|
Power Requirements| 12V DC, 2A power adapter with center-pin positive polarity
ENVIRONMENT|
Operating Temp| 32° to 104° F (0° to 40° C)
Storage Temp| -4° to 140° F (-20° to 60° C)
Humidity| 0-80% RH, non-condensing
CONTROL|
Front Panel| Push Buttons with LED indicators
RS-232| Via Serial @ 115200 bps
Hot Keys| Via Keyboard
OTHER|
Emulation| Keyboard, Mouse and Video
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>