SmartAVI SWP-T10 Wall Plate Extender User Manual

SmartAVI SWP-T10 Wall Plate Extender

Product Information

The SWP-T10 Wall Plate Extender 1080p is a device that extends VGA, stereo audio, HDMI, IR, and RS232 signals with CAT5e/6 cables up to 70 meters. It includes a transmitter (SWP-T10) and a power supply (PS12V2A).

Specifications

• Input ports: 1 x HDMI, Type A 19-pin, female; 1 x VGA HD-15, female; 1 x AUDIO IN (Stereo); 1 x IR IN; 1 x RS-232 3p captive screw connector; 1 x 2p captive screw connector
• Output ports: 1 x IR OUT; 1 x RJ45; 1 x RS-232 3p captive screw connector
• Max Data Rate: 6.75Gbps
• Maximum Pixel Clock: 225MHz
• Resolutions: Up to 1920×1200 or 1080P@60Hz
• Compliance: HDMI 1.4 and HDCP1.2
• Frequency Response: 20Hz ~ 20KHz
• Stereo Channel Separation: >75dB@20Hz ~ 20KHz
• Bandwidth: 20Hz ~ 25KHz
• Power Input: DC 12V
• Power Consumption: N/A
• Dimensions: N/A
• Weight: N/A
• Operating Temp.: N/A
• Storage Temp.: N/A
• Humidity: N/A
• ESD Protection: N/A

Product Usage Instructions

Connecting the SWP-T10 Transmitter and HDX RX Receiver

1. Install the SWP-T10 transmitter and place the SmartAVI HDX RX receiver unit in close proximity to the output device.
2. Connect a Cat5e/6 cable between the TX and RX units (up to 70m).
3. Connect a signal source to the SWP-T10 via HDMI, VGA, Stereo Audio, RS232, or IR connectors.
4. Connect the HDX RX unit to the desired output device.
5. Connect a 12V power supply to either the SWP-T10 or the HDX RX unit. The other device will be powered via POE (Power over Ethernet).
6. Use the TX front panel SELECT SOURCE button to switch between source signals. Using automatic selection will select the last source connected.

Optional Connections

1. To remotely communicate with or control your RS232 device, connect an RS232 cable between SWP-T10 and a personal computer, and a RS232 cable from the HDX RX unit to any RS232 device.
2. To extend IR remote control from the SWP-T10 to the HDX RX unit, connect an IR receiver to the SWP-T10 and an IR Emitter to the HDX RX for infrared remote control up to 20m.

Methods to Control SWP-T10

• Front Panel Button: The Select/Auto button selects an input source. Press and hold the button to enter the automatic switching mode. Press and hold again to exit the automatic switching mode.
• RS-232 External Protocol (PC User): Supports bi-directional RS-232 pass-through control. Use the following settings: 9600 baud rate, 8 data bits, no parity bits, 1 stop bit, and no flow control.

Table 1: Command Protocol

FAQ

• Q: What is the maximum distance the SWP-T10 can extend signals?
  A: The SWP-T10 can extend signals with CAT5e/6 cables up to 70 meters.

• Q: Can I control my RS232 device remotely?
  A: Yes, you can connect an RS232 cable between SWP-T10 and a personal computer, and an RS232 cable from the HDX RX unit to any RS232 device to remotely communicate with or control your RS232 device.

• Q: How do I switch between different source signals?
  A: You can use the TX front panel SELECT SOURCE button to switch between source signals. Automatic selection will select the last source connected.

• Q: How do I enable or disable auto-switching?
  A: To enable auto-switching, press and hold the front panel SELECT SOURCE button until the AutoSwitch LED lights up. To disable auto-switching, press and hold the button again.

WHAT’S IN THE BOX

APPLICATION DIAGRAM

CONNECTING THE HDX-WPRO

1. Install the SWP-T10 transmitter and place the SmartAVI HDX RX receiver unit near the output device.
2. Connect a Cat5e/6 cable between the TX and RX units (up to 70m).
3. Connect a signal source to the SWP-T10 via HDMI, VGA, Stereo Audio, RS232, or IR connectors.
4. Connect the HDX RX unit to the desired output device.
5. Connect a 12V power supply to either the SWP-T10 or the HDX RX unit. The other device will be powered via POE (Power over Ethernet).
6. Use the TX front panel SELECT SOURCE button to switch between source signals. Using automatic selection will select the last source connected.

Optional:

1. Connect an RS232 cable between SWP-T10 and a personal computer and an RS232 cable from the HDX RX unit to any RS232 device to remotely communicate with or control your RS232 device.
2. To extend IR remote control from the SWP-T10 to the HDX RX unit, connect an IR receiver to the SWP-T10 and an IR Emitter to the HDX RX for infrared remote control up to 20m

Overview

SWP-T10 FRONT

SWP-T10 BACK

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS

PORTS
Input ports| 1 x HDMI, Type A 19-pin, female; 1 x VGA HD-15, female;

1 x AUDIO IN(Stereo);1 x IR IN; 1 x RS-232 3p captive screw connector; 1 x 2p captive screw connector

Output ports| 1 x IR OUT; 1 x RJ45; 1x RS-232 3p captive screw connector;
VIDEO
Max Data Rate| 6.75Gbps
Maximum Pixel Clock| 225MHz
Resolutions| Up to 1920×1200 or 1080P@60Hz
Compliance with HDMI standard| Supports HDMI 1.4 and HDCP1.2
AUDIO
Frequency Response| 20Hz ~ 20KHz
Stereo Channel Separation| >75dB@20Hz ~ 20KHz
Bandwidth| 20Hz ~ 25KHz
OTHER
Power Input| 12V DC or 24V DC, 2A
Power Consumption| undetermined
Dimensions| 4.6” W x 4.6” D x 1.45” H
Weight| 0.75lbs
Operating Temp.| 0° to +40°C (32° to 104°F)
Storage Temp.| -20˚C ~ 60˚C / -4 ˚F ~ 140 ˚F
Humidity| 10% ~ 90%
ESD Protection| Human body model:

±8kV (air-gap discharge)

±4kV (contact discharge)

ORDER INFO

ORDER INFO

Part No.| Description
SWP-T10| HDMI, VGA, Stereo Audio, IR POE Extender with Integrated Scaler and Converter. Includes [SWP-T10-TX, PS12VD2A-WLLMNT]

METHODS TO CONTROL SWP-T10

Front Panel Button
The Select/Auto button selects an input source. If you press and hold the button, the SWP-T10 will enter the automatic switching mode and the Auto- Switch LED lights up. If you press and hold the button again, the SWP-T10 will exit the automatic switching mode.

RS-232 External Protocol (PC User)

• Supports bi-directional RS-232 pass-through control.
• This protocol is for communication between the PC user and the board. The following settings should be used: 9600 baud rate, 8 data bits, no parity bits, 1 stop bit, and no flow control.

Table 1:| Command Protocol|
---|---|---
Switch to HDMI| Changes the source to HDMI| //HD
Switch to VGA| Changes the source to VGA| //VG
Auto ON| Enable auto-switching by detecting hot plug.| //AE
Auto OFF| Disable auto-switching by detecting hot plug.| //AD
RES 1| Select Change the resolution to 1920 x 1200.| //R1
RES 2| Select Change the resolution to 1920 x 1080.| //R2
RES 3| Select Change the resolution to 1360 x 768.| //R3
RES 4| Select Change the resolution to 1280 x 720.| //R4
RES 5| Select Change the resolution to 1024 x 768.| //R5
SW Update| Software update for MSTAR chip.| //SU
Reset to Default| Reset to factory defaults| //RD
Table 2:| Query Protocol|
Version| Check the current version of MSTAR software.| //V?

Version Vx.x.x

CHK RES| Check the current resolution.| //R?

Resolution: xx

CHK SRC| Check the current source.| //S?

Input: xx

IR Function
Control devices like HDTVs, Blu-ray players, and more with

IR Cable Pin Assignment

IR Receiver (RX)

IR Emitter (TX)

NOTICE

• The information contained in this document is subject to change without notice. SmartAVI makes no warranty of any kind about this material, including but not limited to, implied warranties of merchantability and fitness for a particular purpose.
• SmartAVI will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
• No part of this document may be photocopied, reproduced, or translated into another language without prior written consent from SmartAVI Technologies, Inc.

Designed and Manufactured in the USA

• 800.AVI.2131•818.503.6200
• Tel: 818-503-6200
• 2455 W Cheyenne Ave, Suite 112 North Las Vegas, NV 89032
• SmartAVI.com.

Many industry-leading companies have recognized the innovation and power of SmartAVI’s technologies and have successfully implemented them within their systems. Users of SmartAVI technology include

References

• Home - SmartAVI

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>