TAKSTAR TS-3380 Wireless Microphone User Manual

**TAKSTAR TS-3380 Wireless Microphone User Manual

**

Function Descriptions

Receiver Front Panel

1. Function Button: used to select channel, adjust/sync/scan frequency, etc.
2. LCD Display: displays sync status, frequency, received signal level, etc.
3. IR Sync Window: sends frequency parameters to transmitter, used in conjunction with the [SET] button.
4. Power Switch: controls receiver power supply.

Receiver Rear Panel

1. Antenna: A/B antenna.
2. Audio Balanced Output: XLR type socket, provides independent signal output for each channel.
3. Mixed Audio Output: mixes audio signals of both channels into one output.
4. Power Socket: connects to DC 12V power supply; the center electrode connects to positive voltage.

LCD Display

1. RF Indicator : displays the received signal strength.
2. AF Indicator: displays the audio signal strength.
3. FREQUENCY : displays the operating frequency.
4. CH: displays the default channel.
5. MUTE : muted status

Handheld Transmitter

1. Mic Grille & Capsule: the mic grille protects the capsule which converts sound into electrical signal, and prevents the mic from rolling on the table.
2. Display Screen : shows information such as operating frequency and battery power.
3. Power Switch : for turning on/off the transmitter power.
4. Mic Body : assembles the grille and capsule on the top, houses the battery and transmitting circuit board inside, and includes an internal transmitting antenna at the bottom.
5. IR Sync Window: receives frequency parameters from receiver, used in conjunction with the [SET] button on receiver. (placed on mic body behind screw cover).
6. Battery Compartment: for loading 2pcs AA batteries (please observe the polarity of battery placement).

Operation Instructions

1. Adjust Frequency Manually
   On home screen, short press [SET] button twice, then short press [▲] or[▼] of the corresponding channel to adjust its operating frequency to desired, and stop pressing until the frequency stops blinking.
   (Note: once frequency is adjusted, follow below IR Sync steps to pair transmitter with receiver)

2. IR Sync
   On home screen after selecting a desired operating channel, turn on the transmitter power, align both IR windows ofthe transmitter and the receiver(at 10~30cm distance), short press [SET]to start syncing, in which case the screen will display the IR interface and subsequently the syncing process as shown in below figure. Once synced, the frequencies shown on the receiver and the transmitter should be the same. Retry by short pressing [SET] again if it fails to sync.

3. Adjust Frequency Numbering
   On home screen, short press [SET] button three times, then short press [▲] or [▼] of the corresponding channel to adjust the frequency number to desired (selectable from 1~14), and press [SET] to confirm.

4. Auto Scan
   On home screen, short press [SET] button four times, then short press [▲] or [▼] of a channel to start automatic frequency scan for the corresponding channel. The frequency on screen keeps changing until it finds a clean frequency. Next, turn on the transmitter power, align both IR windows of the transmitter and the receiver (at 10~30cm distance), short press [SET] to start syncing.
   (Note: when using multiple sets together, keep the already-paired transmitters on while performing auto scan on the next receiver set.)

5. Adjust Volume
   On home screen, short press [▲] or [▼] of the corresponding channel to adjust its volume level (31 levels in total).

Safety Instructions

To avoid electric shock, overheat, fire, radiation, explosion, mechanical risk and injury or property loss due to improper use, please read and observe the following items before use:

1. Please check if the power of the connected equipment matches with that of this product before operation. Adjust the volume to proper level during operation. Do not operate at overpower or high-volume level for extended time to avoid product malfunction or hearing impairment.
2. If there is any abnormality during use (e.g. smoke, strange odor), please kill the power switch and unplug from power source,then send the productto the local dealerforrepair.
3. Never use any replacement battery with broken insulation. Do not charge non-chargeable battery.
4. Dispose waste batteries in designated dustbin for sorting.Do not use them as children’s toy nor discard directly to avoid health risk or environmental damage.
5. Keep this product and its accessories in a dry and ventilated area.Do not store in a humid or dusty area for extended time. Keep away from fire,rain, liquid intrusion, bumping,throwing, vibrating, orfrom blocking any ventilation openings,to prevent malfunction.
6. The product must, if applicable, be fixed firmly in place if installed on walls or ceilings at adequate strength to preventfrom falling.
7. Please abide by safety rules during operation. Do not use the productin places prohibited by laws orregulations to avoid accident.
8. Do not disassemble or repair the product by yourself to avoid injury. If you have any questions orrequire any services, please contact ourlocal dealer.

Troubleshooting

dead;receiver power supply is not properly connected.
No RF signal on receiver.| Different frequency between transmitter and receiver; or out of effective range.
Has RF signal but no AF.| Transmitter mic is not connected.
Loud background noise in audio signal| Low outputlevel on receiver;there is interference signal;receiver antennas are notinstalled, lowering S/N ratio.
Audio signal distortion.| Speak too close to the transmitter mic. Receiver output level is too high.
Short operating distance, unstable signal| Receiver antennas are not properly installed; or there is strong electromagnetic interference around.

Scan for more Product information

Guangdong Taster Electronic Co., Ltd.
Address: No. 2 Fu Kang YiRd., Longxi Boluo Huizhou, Guangdong 516121 China
Tel: 86 752 6383644 Fax: 86 752 6383952
Email: sales@takstar.com
Website: www.takstar.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>