medela Double Electric Breast Pump Instruction Manual

medela Double Electric Breast Pump

Specifications

• Product Name : Swing MaxiTM Electric Breast Pump
• Model : Not specified
• Languages : English, German, French, Italian
• Contents : User Manual, Breast Pump

Important Safety Information
Please read all instructions before using this product. Keep these instructions for future reference. Failure to observe these instructions can lead to personal injury or damage to the product.

When using electrical products, especially when children are present, basic safety precautions must always be followed.

Warnings

• WARNING: Can lead to serious injury or death. To avoid health risks and reduce the risk of severe injury, consult with a licensed healthcare professional before using this product.
• CAUTION: Can lead to minor injury. To avoid health risks and reduce the risk of injury, follow the instructions provided.
• NOTICE: Useful or important information that is not related to safety.

Intended Purpose
The Swing MaxiTM Electric Breast Pump is designed for expressing breast milk for feeding purposes. It is intended for personal use and is not suitable for multiple users.

Product Description

Description of the Device
The Swing MaxiTM Electric Breast Pump is a compact and portable device that allows mothers to express breast milk efficiently and comfortably. It is designed with user-friendly features for ease of use.

The Device Includes

• Swing MaxiTM Electric Breast Pump
• User Manual

Getting Started

Cleaning Before First Use
Before using the Swing MaxiTM Electric Breast Pump for the first time, it is important to clean all parts of the device. Follow the instructions provided in the user manual for proper cleaning procedures.

Charging the Battery
The Swing MaxiTM Electric Breast Pump is equipped with a rechargeable battery. Before using the device, ensure that the battery is fully charged. Connect the device to a power source using the provided charger and allow it to charge until the battery is full.

Cleaning

Washing and Sanitising the Pump Set
After each use, it is essential to wash and sanitise the pump set to maintain hygiene. Follow these steps

1. Disassemble the pump set by removing the breast shield, connector, and bottle.
2. Rinse all parts with warm water to remove any remaining milk.
3. Wash all parts with mild soap and warm water. Use a brush to clean hard-to-reach areas.
4. Rinse all parts thoroughly with clean water.
5. Sterilise all parts using a sterilising solution or by boiling them in water for a few minutes.
6. Allow all parts to air dry before reassembling the pump set.

Cleaning the Pump Unit
The pump unit should be cleaned regularly to ensure optimal performance. Follow these steps

1. Disconnect the pump unit from the power source.
2. Wipe the exterior of the pump unit with a clean, damp cloth.
3. Do not immerse the pump unit in water or other liquids.

Cleaning the Tubing
The tubing should be cleaned regularly to prevent milk residue buildup. Follow these steps

1. Disconnect the tubing from the pump unit and breast shield.
2. Rinse the tubing with warm water to remove any milk residue.
3. Allow the tubing to air dry completely before reattaching it to the pump unit and breast shield.

Assembling the Breast Pump

Selecting the Correct Breast Shield Size
It is important to select the correct breast shield size for optimal comfort and efficiency. Follow these guidelines

• Measure your nipple diameter using the provided measurement guide.
• Refer to the sizing chart in the user manual to determine the appropriate breast shield size.

Assembling the Pump Set
Follow these steps to assemble the pump set

1. Attach the breast shield to the connector.
2. Screw the bottle onto the connector.

Preparing for Single Pumping
If you prefer to express milk from one breast at a time, follow these steps

1. Attach the breast shield to one side of the pump set.
2. Ensure that the other side of the pump set is closed or covered.

Preparing for Double Pumping
If you prefer to express milk from both breasts simultaneously, follow these steps

1. Attach a breast shield to each side of the pump set.

Operating the Breast Pump
Before operating the Swing MaxiTM Electric Breast Pump, ensure that all parts are properly assembled and the device is clean and charged.

Buttons and Status Light
The breast pump is equipped with buttons and a status light for easy control and monitoring. Refer to the user manual for detailed information on the buttons and their functions.

Expressing Your Breast Milk
Follow these steps to express your breast milk using the Swing MaxiTM Electric Breast Pump

1. Position the breast shield over your breast, ensuring a comfortable fit.
2. Press the power button to start the pumping process.
3. Adjust the suction level and cycle speed according to your preference.
4. Continue pumping until you have expressed the desired amount of milk.

Pausing
If you need to pause the pumping process temporarily, press the pause button. To resume pumping, press the pause button again.

• Switching Off
  To switch off the Swing MaxiTM Electric Breast Pump, press and hold the power button until the device turns off.

• After Pumping
  After expressing your breast milk, disassemble the pump set and clean all parts according to the cleaning instructions provided. Store the expressed milk in a clean, sterilised container following the storage guidelines.

Handling of Breast Milk

General Storage Guidelines
Follow these guidelines for storing breast milk

• Label the container with the date and time of expression.
• Store breast milk in a clean, sterilised container with a tight-fitting lid.
• Store breast milk in the refrigerator or freezer according to your preference.

Freezing
If you choose to freeze breast milk, ensure that it is stored in a freezer- safe container. Leave some space at the top of the container to allow for expansion during freezing.

Thawing
When thawing frozen breast milk, do not use a microwave or boiling water. Thaw it slowly in the refrigerator or by placing the container in warm water.

Troubleshooting
If you encounter any issues with the Swing MaxiTM Electric Breast Pump, refer to the troubleshooting section in the user manual for possible solutions. If the problem persists, contact the manufacturer for assistance.

Accessories
Additional accessories for the Swing MaxiTM Electric Breast Pump may be available. Refer to the user manual or contact the manufacturer for more information.

Warranty
The Swing MaxiTM Electric Breast Pump may come with a warranty. Refer to the warranty section in the user manual for details on coverage and terms.

Disposal
Follow local regulations for the proper disposal of the Swing MaxiTM Electric Breast Pump and its components. Do not dispose of the product in regular household waste.

FAQ

• Q: How often should I clean the breast pump?
  • A: The breast pump should be cleaned after each use to maintain hygiene and performance.
• Q: Can I use the breast pump while breastfeeding?
  • A: It is recommended to consult with a licensed healthcare professional before using the breast pump while breastfeeding.
• Q: Can breast milk transmit viruses?
  • A: Breast milk can transmit viruses. If you have any concerns, consult with a licensed healthcare professional.
• Q: Can I share the breast pump with others?
  • A: The Swing MaxiTM Electric Breast Pump is intended for personal use and is not suitable for multiple users.
• Q: How do I know if the breast shield size is correct?
  • A: If you experience discomfort or pain while using the breast pump, it may indicate an incorrect breast shield size. Seek assistance from a lactation consultant or breastfeeding specialist to ensure a proper fit.

Important safety information

• Please read all instructions before using this product. Keep these instructions for future reference.
• Warnings identify all instructions that are important for safety. Failure to observe these instructions can lead to personal injury or damage to the product.

The following symbols and signal words show the significance of the warnings

• WARNING Can lead to serious injury or death.
• CAUTION Can lead to minor injury.
• NOTICE Can lead to material damage (not related to personal injury).
• Information Useful or important information that is not related to safety.

When using electrical products, especially when children are present, basic safety precautions must always be followed.

WARNING
To avoid fire, electric shock, or serious burns

• Only use the power adapter and cable that comes with the device. An inadequate power source or cable may result in a fire hazard, electric shock or malfunction of the device.
• Never operate an electrical device if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. If damage is found, immediately discontinue use of power adapter and call Medela Customer Service.
• Do not use an electrical product that has been exposed to water or other liquids including:
  • Do not use while bathing or showering.
  • Never place or drop into water or other liquids.
  • Do not run water over the pump unit.
  • I f an electrical product has been exposed to water or other liquids, do not touch, unplug the device from electrical outlet, turn off and contact the manufacturer.

WARNING
To avoid health risks and reduce the risk of severe injury

• Do not use the device while operating a moving vehicle.
• Pumping can induce Labour. Do not pump until after giving birth. If you become pregnant while breastfeeding or breast pumping, consult with a licensed healthcare professional before continuing.
• If infected with Hepatitis B, Hepatitis C, or Human Immunodeficiency Virus (HIV), pumping breast milk will not reduce or remove the risk of transmitting the virus to your baby through your breast milk.
• Wash all parts that come into contact with your breast and breast milk after every use.
• This appliance is not intended for use by persons (including children up to 14 years) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children must not play with the appliance.
• Cleaning and maintenance must not be performed by children without supervision.

CAUTION
To avoid fire or burns

• Make sure the voltage of the power adapter is compatible with the power source. See chapter 15 for technical specifications.
• Always unplug electrical products immediately after use except for when charging.
• Do not place or store the product where it can fall or be pulled into a tub or sink.
• The device and its accessories are not heat-resistant. Keep away from heated surfaces or open flames.
• Do not use near flammable materials.

CAUTION
To avoid health risks and reduce the risk of injury:

• This is a single-user product. Use by more than one person may present a health risk and voids the warranty.
• This product cannot be serviced or repaired. Do not repair yourself. Do not modify the device.
• Never use a damaged device. Replace defective or worn parts.
• Use the device only for its intended purpose as described in these instruction for use.
• Do not use the device while sleeping or overly drowsy.
• If tubing becomes mouldy, discontinue use and replace tubing.
• Do not microwave or boil breast milk. Microwaving can cause severe burns to baby’s mouth from hot spots that develop in the milk during microwaving (Microwaving can also change the composition of breast milk).
• Clean and sanitise all parts that come into contact with your breast and breast milk prior to first use.
• Only use Medela recommended parts with the device.
• If pumping is uncomfortable or causing pain, turn the unit off, break the seal between the breast and the breast shield with your finger and remove the breast shield from your breast.
• While some discomfort may be felt when first using a breast pump, it should not cause pain. If you are unsure about correct breast shield sizing please visit www.medela.com or see a lactation consultant/breastfeeding specialist who can help you get a proper fit.

NOTICE
Pay attention to the following

• Take appropriate care in handling bottles and components:
• Plastic bottles and parts become brittle when frozen and may break when dropped.
• Bottles and parts may become damaged if mishandled (e.g., dropped, over-tightened, or knocked over).
• Do not use the breast milk from bottles or components that show signs of damage.

Intended purpose
The Swing Maxi breast pump is a powered breast pump to be used by lactating women to express and collect milk from their breasts. The Swing Maxi breast pump is intended for a single user.

Product description

Description of the device

• The Swing Maxi is a personal-use electric breast pump that includes 2-Phase Expression technology and is capable of single and double pumping. It consists of a pump unit, two pump sets (breast shield, connector and bottle) and a tubing.
• The operating life of the Swing Maxi breast pump is 250 hours.

The device includes

• Refer to figure 5 on the foldout pages.
• 5-01 (Disposable) protective cover
• 5-02 Personal Fit Flex breast shield S 21 mm (2 pcs)
• Personal Fit Flex breast shield M 24 mm (2 pcs) ¢5-03 Personal Fit Flex connector (2 pcs)
• 5-03-1 Connector body (2 pcs)
• 5-03-2 Membrane (2 pcs)
• 5-04 Bottle (2 pcs)
• 5-05 Lid (2 pcs)
• 5-06 Bottle stand (2 pcs)
• 5-07 Tubing
• 5-07-1 Short ends of tubing (connect to one or two connectors)
• 5-07-2 Tubing holder
• 5-07-3 Long end of tubing (connects to pump unit)
• 5-08 Power adapter with cable¢5-09 Pump unit

Getting started

Cleaning before first use
It is important to do the following before using the breast pump for the first time:

1. Remove the protective cover ( 5-01) from the breast shields ( 5-02).
2. Disassemble and clean all parts (except for the tubing) according to the cleaning instructions – see section 5.1.

Charging the battery
Charge the battery for two hours.

1. Use the power cable to connect the pump unit with the power adapter.
2. Plug the power adapter into a wall outlet.
   During charging, the status light is pulsing in green colour.
   When charging is complete, it lights up steadily in green colour.

Information
You can use the breast pump while charging the battery. However, it will charge in a slower mode when the pump is running.

Cleaning

Washing and sanitising the pump set

• Washing and sanitising are two different activities. They must be done separately to protect you and your baby, and to maintain the performance of the device.
• Wash – To clean the surfaces of the parts by physically removing contamination.
• Sanitise – To kill microorganisms, such as fungi, bacteria or viruses, that may be present on the surfaces of the parts.

CAUTION
To keep the pump parts clean and hygienic

• Separate and wash all parts that are exposed to breast milk immediately after use. This will help to remove breast milk residue and prevent growth of bacteria.
• Wash hands thoroughly with soap and water.
• Only use drinking-quality tap water or bottled water for cleaning.
• Do not place pump parts directly in the sink to rinse or wash. Use a clean wash basin used only for infant feeding items.
• Do not use a dish towel to rub or pat items dry.
• Do not use disinfectants for cleaning.

NOTICE
To prevent damage to the tubing.

Do not clean the tubing as described below. Follow the instructions in section 5.3. NOTICE
Pay attention to the following

• Take care not to damage parts of the pump set during cleaning.
• Store the dried pump set in a clean bag/container until next use.
• Do not store wet or damp parts as mould may develop.
• If you notice a white residue on the parts after boiling, your water may have a high mineral content. Remove residue by wiping parts with a clean towel and allow to air dry.
• Distilled water is recommended when boiling parts to prevent substantial mineral build-up over time, which may compromise your parts.

Information
If using the dishwasher, parts may become discoloured. This will not impact the part function.

What to do when: See detailed instructions on the next page.

Before first use, remove and dispose of the protective cover ( 5-01) from the breast shield ( 5-02). Wash and sanitise the pump set and bottles following the steps 1 to 4 below before using them for the first time. Wash your pump set and bottles after each use and sanitise the parts once per day after they have been washed.

1. Disassemble
   Refer to figure ¢1 on the foldout page.

2. Disassemble the pump set into its individual parts (breast shield, connector and bottle).

3. Open the connector ( 1-01) by squeezing both flaps and swiveling the lid upwards and remove the membrane ( 1-02).

4. Separate the bottles, lids and bottle stands.

5. Wash (before first use and after each use)
   Rinse and wash by hand

6. Rinse the disassembled parts, except for the tubing, with cool water (approx. 20 °C).

7. Clean these parts with plenty of warm, soapy water (approx. 30 °C). Use a commercially available washing-up liquid.

8. Rinse the parts with cool water for 10 to 15 seconds (approx. 20 °C).
   Wash in dishwasher Place the disassembled parts, except for the tubing, on the top rack or in the cutlery section. Use a commercially available dishwashing detergent.

9. Sanitise (before first use and once per day)

10. Dry
    Allow to air-dry on a clean, unused dish towel or paper towel. Store the dry parts in a clean environment. Do not store parts in an airtight container/bag if moist. It is important that all residual moisture dries.

Cleaning the pump unit

CAUTION
To prevent electric shock and damage to the material:

• Unplug the pump unit before cleaning it.
• Do not immerse the pump unit in water.
• Do not spray or pour liquid directly onto it.

1. Wipe the pump unit with a clean towel moistened with soapy water.
2. Wipe the pump unit dry with a clean, dry towel.

Cleaning the tubing

• CAUTION
  If the tubing becomes mouldy, discontinue use and replace tubing.

• NOTICE
  Do not use the device with wet tubing; doing so will damage it.

• Washing
  Since the tubing only conveys an air flow (no contact with milk), normally cleaning of the tubing is not necessary.

• Information
  Inspect the tubing. If you find condensation in the air tube, wash and dry it immediately or replace it. If you see breast milk inside the tubing do not attempt to wash or sanitise it. Instead contact the manufacturer.

1. Separate the tubing from the device.
2. Rinse the tubing by pouring cool water into both short tubing ends until it flows out of the long tubing end.
3. Wash the tubing in warm, soapy water.
4. Rinse the tubing with clear water.

Drying

1. Shake out any water droplets.
2. Hang the tubing to air dry.
3. Make sure that the tubing is completely dry before using it.

Assembling the breast pump
Only use clean and dry parts for assembly. Refer to chapter 5 for cleaning.

Selecting the correct breast shield size
Refer to figure ¢6 on the foldout pages.

1. For proper sizing, measure the diameter of your nipple ( 6-01).
2. Select the breast shield that is slightly larger than your nipple ( 6-02). For more information on breast shield sizing, visit www.medela.com .

Assembling the pump set

CAUTION
To prevent contamination of your milk:

• Wash hands thoroughly with soap and water before touching the pump unit, parts of the pump set and breasts.
• Dry your hands with a fresh towel or a single-use paper towel.
• Avoid touching the inside of bottles and lids.

To make sure that the device works properly and safely

• Check pump set components for wear or damage before use. Replace if necessary.
• Always inspect all parts prior to use for cleanliness. If dirty, clean according to chapter 5.

NOTICE
To prevent damage to the pump unit all components must be completely dry before use.

Refer to figure 2 on the foldout pages.

1. 2-01 Carefully insert the yellow membrane with the flap into the opening of the connector body.
   Make sure that the membrane forms a seal around the edge of the connector body.

2. 2-02 Close the connector lid until it audibly clicks.

3. Screw the connector onto the bottle.

4. Carefully push the breast shield into the connector.

5. The oval breast shields can be rotated (360°) and placed in the desired position to have the most comfortable fit for you.

6. 2-03 Insert the short end of the tubing into the connector.

7. 2-04 Insert the long end of the tubing into the pump unit as far as it will go.

Preparing for single pumping
Refer to figure ¢3 on the foldout pages.

1. Assemble one pump set as described in section 6.2.

2. Insert the unused tubing end into the tubing holder.
   3-01 Correctly assembled system for single pumping.

3. Place the breast shield on the breast so that the nipple is properly centred in the tunnel.

4. Hold the breast shield and connector onto your breast with your thumb and index finger.

5. Support your breast with the palm of your hand.

6. Start pumping as described in section 7.3.

Preparing for double pumping
Refer to figure 4 on the foldout pages.

1. Assemble two pump sets as described in section 6.2.
   4-01 Correctly assembled system for double pumping.

2. Place the breast shields on the breasts so that the nipple is properly centred in the tunnel.

3. Hold the breast shields and connectors onto your breasts with your thumb and index finger.

4. Support your breast with the palm of your hand.

5. Start pumping as described in section 7.3.

Operating the breast pump

Mimicking the baby´s rhythm (2-phase expression)

• Babies use a “two-speed” sucking action. At first, they suck quickly, and then they switch to a slower, deeper sucking rhythm once milk starts to flow. The quicker sucking action stimulates the milk ejection reflex and triggers the milk flow; the slower sucking draws the milk out for the feeding phase.
• The pump mimics the baby´s natural sucking rhythm by using a “two-speed” pumping action, the so called “2-Phase expression”.
• The breast pump begins with a fast sucking action called the stimulation phase. When you see milk flow or feel milk ejection, you can then press the “Let-down” button to switch to the expression phase, which is slower than the previous one. If you do not press the Let-down button, the expression phase will automatically start after the pump has been running for one minute in the stimulation phase.

Buttons and status light

Expressing your breast milk

CAUTION
In case of pain or insufficient milk expression

• Do not hold the pump set by the bottle. This can lead to compression and blockage of the milk ducts and engorgement.
• Do not try to express with vacuum that is too high and uncomfortable (painful). The pain, along with potential breast and nipple trauma, may decrease milk output.
• Contact your healthcare professional or breastfeeding specialist if you can express only minimal or no milk or if expression is painful.

NOTICE
Make sure that the tubing is not kinked or pinched while pumping.

1. Place the breast shield on the breast so that the nipple is properly centred in the tunnel.

2. Press the On/Pause/Off button to start pumping.
   The stimulation phase begins and the status light is flashing.

3. Adjust the vacuum with the Increase vacuum and Decrease vacuum  buttons to  find a comfortable level.

4. As soon as your milk begins to flow, press the Let-down button
   The expression phase begins and the status light is on steadily.
   If the Let-down button is not pressed within one minute, the breast pump will automatically go to expression phase.

5. Adjust the vacuum with the Increase vacuum and Decrease vacuum buttons to find your maximum comfort vacuum (see information below).
   Information

   • Maximum comfort vacuum is the highest vacuum setting where pumping still feels comfort-able. This is different for every mother.
   • Stimulation should be at a comfortable vacuum level, striving for a maximum level is not necessary here.
   • Reassess your maximum comfort vacuum throughout your pumping experience. It can change throughout each stage of lactation.

6. To pause pumping refer to section 7.4 and to switch the pump off refer to section 7.5.
   The breast pump stops automatically after 30 minutes if there is no user interaction with the pump.

Pausing
In both stimulation and expression phase the breast pump can be paused.

This allows you to readjust yourself or your pump set, or attend to your surroundings.

1. For pausing, press the On/Pause/Off button while the breast pump is running.
   The pumping operation stops and the status light is pulsing.

2. To resume pumping, press the On/Pause/Off button again.

Information

• If pumping is not resumed within two minutes, the breast pump turns off automatically.
• If you need to pause for more than two minutes, it is recommended that you restart with stimulation phase.

Switching off
To switch the breast pump off press and hold the On/Pause/Off button for two seconds.

After pumping
Prepare the milk for storage as follows:

1. Use the bottle stand to prevent the bottle from tipping over.
2. Close the bottle with a lid.

Handling of breast milk

General storage guidelines

Storage guidelines for freshly expressed breast milk (for healthy term babies)

Room temperature 16 to 25 °C (60 to 77 °F)| Refrigerator 4 °C (39 °F) or colder| Freezer –18 °C (0 °F ) or colder| Breast milk thawed in the refrigerator
Up to 4 hours is best| Up to 3 days is best| Up to 6 months is best| At room temperature: Up to 2 hours
Up to 6 hours for milk expressed under very clean conditions| Up to 5 days for milk expressed under very clean conditions| *Up to 9 months for milk expressed under very clean conditions| Refrigerator: Up to 24 hours Do not refreeze!

*Guidelines for expressing milk under very clean conditions
Before expressing breast milk, mothers should wash their hands with soap and water or an alcohol-based hand sanitiser. The pump parts, bottles and pumping area must be clean. Breasts and nipples do not need to be washed before pumping

• These guidelines for storage and thawing of breast milk are a recommendation. Contact your lactation consultant or breastfeeding specialist for further information.
• Store breast milk in the coldest spot of the refrigerator (at the back of the glass shelf above the vegetable compartment).

Freezing

NOTICE

• Repeated freeze/thaw cycles destroy the structure of the milk. Therefore, never refreeze breast milk.
• Freeze expressed breast milk in plastic bottles or milk storage bags. Do not fill the bottles or bags more than 3/4 full to allow space for possible expansion.
• Label the bottles or bags with the date and volume of expression.
• Plastic bottles and parts become brittle when frozen and may break when dropped.
• Do not use the breast milk from bottles or components that show signs of damage.

Thawing

CAUTION
Do not thaw or warm breast milk in a microwave or a pan of boiling water. This helps preserve important components and prevents burns.

• To preserve breast milk components, thaw the milk overnight in the refrigerator.
• Alternatively, hold the bottle or bag under warm water (max. 37 °C / 98.6 °F).

NOTICE
Gently swirl the bottle or bag to mix any fat that has separated. Avoid shaking or stirring the milk.

Troubleshooting

In case of an unexpected behaviour of the breast pump check with the troubleshooting table if you find the issue in the column “Problem” and follow the instructions in the column “Solution”.

Troubleshooting table

Charge for 15 minutes before restarting the pump. Charging is indicated by the status light pulsing in green. If the pump is still not working contact the Medela Customer Service.
The breast pump generates only constant vacuum instead of sucking cycles| Contact the Medela Customer Service.
The status light is flashing rapidly in red when you try to pump or charge the breast pump| Charging/pumping is not possible when the battery temperature is too high. Allow the pump unit to cool down, then resume charging/ pumping. If the status light is still flashing rapidly in red, a device fault occurred. Contact the Medela Customer Service.
There is low or no suction|

• Make sure that all pump set components are clean and dry and that connections are secure.
• While pumping, make sure the breast shields form a complete seal around the breast.
• When single pumping, make sure that the unused tubing end is correctly plugged into the tubing holder.
• If suction does not improve after having followed these steps, contact the Medela Customer Service.

The breast pump is not respond- ing as expected|

• Press and hold the On/Pause/Off button for two seconds to switch the breast pump off, then restart the breast pump.
• If there is no change, contact the Medela Customer Service.

The pump unit’s exterior got wet| Unplug the pump unit from the power source and turn it off. Dry off the exterior of the pump unit.
The pump unit has been submerged in water| Unplug the pump unit from the power source and turn it off. Contact the Medela Customer Service.

If you have not resolved the problem with the breast pump or you have further questions, please contact the Medela Customer Service. For contact data visit www.medela.com. Under “Contact” choose your country.

Accessories
The following products are sold separately

• PersonalFit Flex breast shield sizes S (21 mm), M (24 mm), L (27 mm), XL (30 mm)
• Swing Maxi tubing
• PersonalFit Flex connector
• Bottle
• Depending on your region, check local website/shops for availability.

Warranty

Find information on the international warranty on www.medela.com/ewarranty.

Disposal
Disposal of the device

• At the end of its operating life, separate the parts of the breast pump and dispose of accord-ing to the following instructions.
• Breast shields, connector, tubing and accessories
• The parts are made of plastics that are not harmful to the environment when disposed of as household waste. Recycle or dispose of according to local regulations.

Pump unit and power adapter

• Do not dispose of electric or electronic equipment together with unsorted municipal waste, but collect it separately.
• In the European Union the manufacturer or its vendor must take back waste equipment. Other countries may have similar collection and recycling systems. Dispose of the waste equipment according to local regulations.
• Inquire at the point of sale or contact your local authority for appropriate collection points for waste equipment.
• The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

CAUTION
Hazardous materials present in electric/electronic equipment may harm human health and the environment if the waste equipment is not disposed of properly.

Meaning of symbols

• Symbols used in these instructions
• Symbols found on the product parts and its packaging.
  Note: Symbols on the power adapter may vary depending on the market the unit is sold.

International regulations

Electromagnetic compatibility (EMC)
The Swing Maxi breast pump complies with all requirements of the relevant standards and regulations with regard to electromagnetic emission and immunity to interference.

WARNING
The electric breast pump Swing Maxi should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the electric breast pump Swing Maxi should be observed to verify normal operation in the configuration in which it will be used. Wireless communications equipment such as wireless home network devices, mobile phones, cordless telephones and their base stations, walkie-talkies can affect the electric breast pump and should be kept at a distance of at least 30 cm away from the device.

Drinking equipment
Parts intended for infant feeding comply with the European Standard EN 14350.

Technical specifications

For common technical data see chapter 16.

Power adapter

• Model (varies according to market location):
• MS-V2000U050-010B0-DE/MS-V2000U050-010B0-GB/MS-V2000U050-010B0-US/MS-V2000U050-010B0-CN/MS-H2000U050-010B0-AU

Materials touching skin or coming in contact with milk

• Breast shield: Polypropylene, thermoplastic elastomer
• Connector body: Polypropylene
• Membrane: Silicone
• Bottle: Polypropylene
• Lid: Polypropylene

All parts that come in contact with breast milk are not made with BPA (Bisphenol A).

Common data

Vacuum performance (at 500 m above sea level [954.62 hPa ambient pressure]) 45 … 111 cpm

• Operation
• Operation
• Pump unit
  • Size/ 126 x 125 x 58 mm
  • Weight/ 325 g

Battery capacity and type/

Transport/storage

Transport/storage

• Medela AG
• Lättichstrasse 4b 6340 Baar, Switzerland www.medela.com
• International Sales
• Medela AG Lättichstrasse 4b 6340 Baar Switzerland
• Phone +41 41 562 51 51
• www.medela.com
• Austria
• Medela Österreich GmbH Goldschlagstraße 172/4/3 1140 Wien

Austria

• Phone +43 720 310313 – 0
• Fax +43 720 310313 – 999
• info@medela.at
• www.medela.at

France

• Medela France
• 14 rue de la Butte Cordière
• 91154 Étampes Cedex

France

• Phone +33 1 69 16 10 30
• Fax +33 1 69 16 10 32
• info@medela.fr
• www.medela.fr

Germany

• Medela Medizintechnik
• GmbH & Co. Handels KG
• Postfach 1148
• 85378 Eching

Germany

• Phone +49 89 31 97 59-0
• Fax +49 89 31 97 59 99
• info@medela.de
• www.medela.de

Italy

• Medela Italia S.r.l. a socio unico
• Via Turrini, 13/15
• 40012 Calderara di Reno (BO)

Italy

• Phone + 39 051 72 76 88
• Fax + 39 051 72 76 89
• info@medela.it
• www.medela.it
• Switzerland
• Medela Markt Schweiz
• Lättichstrasse 4b
• 6340 Baar

Switzerland

• Phone +41 848 633 352
• Fax +41 41 562 14 42
• contact@medela.ch
• www.medela.ch

© Medela AG/ref. master doc.101042305/A
101042025/2020-09/A Subject to modifications – Not intended for distribution in the USA

References

• Medela Deutschland | Stillprodukte und medizinische Vakuumtechnologie | Medela
• Medela Schweiz | Stillprodukte und medizinische Vakuumtechnologie | Medela
• Breastfeeding & Pumping
• Warranty
• Stillen und Abpumpen
• Homepage Medela | Medela
• Allattamento al seno ed estrazione

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>