ErGear EGESD4B Height Adjustable Electric Standing Desk Instruction Manual
- June 14, 2024
- ERGEAR
Table of Contents
40” Electric Standing Desk
Instruction Manual Rev02(A)
EGESD4B / EGESD4V / EGESD4N
Technical Support:
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm
(CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info: support@ergear.com
Website: https://ergear.com
Tools Needed (Not lncluded)
Specifications
Height Adjustment Range 28.3”–46.5” (72-118cm)
Step 1 Supplied Parts and Hardware
Step 2 Supplied Parts
and Hardware
Step 3 Supplied Parts and Hardware
Step 4 Supplied Parts and
Hardware
Step 5 Supplied Parts and
Hardware Step 1 Assembling and Connecting the Desk Legs
Step 2 Attaching the Side Plates and the Transmission Rod
Before attaching
the transmission rod, measure the heights of the two desk legs to see if they
are set at the same level. If not, insert the transmission rod into the hole
in the left leg.
Turn the rod to adjust the left leg so it’s level with the right leg. Turn the
rod clockwise to lower the left leg or anti-clockwise to raise it.
Ensure the transmission rod
is properly inserted into the hole in the left leg. Smoothly connect the other
end of the rod to the end of the motor drive shaft on the right leg.
Secure the transmission rod
to the motor drive shaft by turning the set screw clockwise.
Step 3 Assembling and Attaching the
Desktop
Attach the controller and hooks to the
desktop.
Step 4 Connecting the
Cables
Step 5 Installing the
Cable Hole Covers
Using the Controller
-
Save Current Height Setting
Short-press the s button, and the display will flash. Press the 1,2,or 3 button to save the current height setting to that button. -
Select Height Setting 1
Press the 1 button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 2
Press the 2 button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 3
Press the 3 button, and the desk will move to the height that was previously set for that button. -
Raise the Desk
Press the button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released. -
Lower the Desk
Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.
Settings
Change Display Height Units| Press and hold the s button until a flashing ‘S-’
is displayed.
Press s again, and ‘Un’ is displayed. Press s to select it, press or to switch
between ‘IN’ (imperial) and ‘SI’ (metric), and press s to save your choice.
Change Collision Detection Sensitivity| Long press the 8 button, ‘S-‘ shows
and flashes. Press s again and the display shows ‘Un.‘ Press or to switch to
‘CF.‘ Press 8 to select. Press or to switch between ‘OFF,‘ Low (L), Normal (n)
or Heavy (H) collision force detection.
Press s to save your choice.
Reset| Press and hold the button for 5 seconds, and the screen will show
‘RES.’ Continue holding until the desk goes down to its lowest level and comes
back up slightly.
Protection Mode Error Codes
Hot| Overheating Protection: When the motor has been working continuously for
2 minutes, it will stop operating to prevent damage from overheating. Wait for
at least 18 minutes before making any further height adjustment.
E10| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power
off, check the connection between the
motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the
things off the desk and try again. If lowering the desk, power off, take the
things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or
incline are detected. If this detection
is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter
is being used, power off the desk, check the connection between power and the
controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter
is being used, power off the desk, check the connection between power and the
controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left
and right legs are at the same height. Adjust if necessary by following the
instructions.
Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections.
Normal operation should return once all connectors are properly connected.
Complete Flexibility.
Total Freedom.
Thank you for choosing this product. We strive to provide you with the best
quality products and service in the industry. Should you have any issues,
please don’t hesitate to contact us.
Technical Support
(US/CA) 1-800-651-9525 Mon–Fri, 8am–8pm
(CST)
(UK) 44-808-196-3875 Mon–Fri, 2pm–10pm (UTC)
Other Info
support@ergear.com
Website
https://ergear.com
860-00288-00 Rev02
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>