cleverio AP300 Air Purifier User Guide

: June 14, 2024
: Cleverio

Table of Contents

cleverio AP300 Air Purifier
Overview
Control panel
Use
Modes and functions
Connect to app
Troubleshooting
Cleaning and maintenance
Safety information
Specifications
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

cleverio AP300 Air Purifier

cleverio-AP300-Air-Purifier-product-image

Overview

$cleverio-AP300-Air-Purifier-01 $1$$

Control panel

$cleverio-AP300-Air-Purifier-01 $2$$

Auto mode button
Fan speed button
Sleep mode button
Fan speed indicator
Remote receiver
Auto mode indicator
Sleep mode indicator
PM2.5 air quality
Time/timer
Wifi indicator
Child lock indicator
Filter indicator
Timer button (press and hold 3 seconds to exit)
Wifi pairing button
Power button
Child lock button (press and hold 3 seconds to exit)

Use

Before first use
Open the front panel of the air purifier, take out the filters and remove the packaging materials before first use. $cleverio-AP300-Air-Purifier-01 $3$$

Install filters
Put the filters back into the air purifier. It’s important that you insert them in the following order:

Insert the HEPA filter first (green fiber surface).
Insert the Cold catalyst/activated carbon filter next (gray fiber surface).
Insert the Pre-filter last. The pre-filter is closest to the cover (metallic mesh surface).

Attach the lid and close the front cover.

Power on/off and placement

Place the air purifier on the floor or on a flat surface, away from any other electrical appliances such as a TV, radio or the outlet of an air conditioner. Avoid placing it in direct sunlight and do not block the inlet or outlet of the air purifier. The air purifier has an anti-tipping protection system built in with a switch on the bottom that turns off the air purifier in case it would tip or fall.
Connect the power cord to a wall socket. The display lights up and the air purifier emits a sound. Press the Power button (15) on the control panel to turn on the air purifier. Press the power button again to turn the air purifier off.

Modes and functions

Auto mode

Press the Auto mode button (1) and the auto mode indicator (6) lights up on the control panel. The air purifier adjusts the speed automatically to improve the measured PM2.5 air quality (8). Press the Auto mode button, Fan speed button (2) or Sleep mode button (3) to exit auto mode.
The particle sensor measures the air quality around the air purifier using a PM2.5 value. The LED indicator around the control panel changes color to reflect the current value following to the table below:

PM2.5 value:
- 0-60
- 60-150
- 150+
LED color:
- Green
- Orange
- Red
Air quality:
- Good
- Poor
- Unhealthy
Fan speed (auto mode):
- Low
- Medium
- High

Fan speed
Press the Fan speed button (2) to cycle between settings low (500 RPM), medium
{700 RPM) and high speed (900 RPM). The fan speed indicator (4) shows the set speed.

Sleep mode
Press the Sleep mode button (3) to enter sleep mode. During sleep mode the air purifier speed is automatically set to low and the lights on the panel turn off. Press any button on the control panel to turn on the lights on the display temporarily. Press the Sleep mode button, Auto mode button or fan speed button to exit sleep mode.
Timer
- Press the Timer button (13) multiple times to set a timer (30 minutes to 12 hours). Each press adds 30 minutes. The timer display (9) counts down and shows the remaining time. The air purifier automatically enters standby mode when the set time has elapsed.
- Press and hold the Timer button for 3 seconds to exit timer mode.
Child lock
- Press the Child lock button (16) to activate the child lock. The child lock indicator (11) lights up and all the buttons on the control panel are locked.
- Press and hold the Child lock button for 3 seconds to unlock the buttons.
- Note! You can still control the air purifier via the app when child lock is on.

Set the time

Press and hold the Auto button for 5 seconds to enter the time settings. The hour digit starts flashing.
Press the Fan speed button (2) to add 1 hour and the Sleep mode button (3) to subtract 1 hour. Press the Auto button to confirm the hour setting and to move on to minutes.
Press the Fan speed and Sleep mode buttons again to set the minutes the same way. Press Auto to confirm.
Note! The time settings reset if the air purifier is unplugged for 10 days or more.

Connect to app

Find and install the app ‘Smart life – Smart living’ on App Store or Google Play, or scan the QR code to the right.
Register an account in the app or log in to an existing one.
Activate location services on your smart device.
Make sure your smart device is connected to your 2.4 GHz wifi.
Turn on the air purifier and wait for the display to light up. Press and hold the Wifi pairing buttom (14). A sound is emitted and the wifi indicator (10) starts flashing.
Press”+” and “Add Device” in the app.
Go to “Small Home Appliances” and choose “Air Purifier {Wi-FQ”.
If you are using the “Smart life – Smart living” account for the first time, enter the details for your 2.4 GHz wifi.
Check if the wifi indicator (10) is flashing rapidly on the control pabel and confirm in the app by selecting “Blink Quickly” when prompted.
The app searches for devices nearby.
A prompt is shown in the app and the wifi indicator (10) lights up with a solid light when the connection is successful.

Note! The pairing procedure may change due to regular app updates. If the instruction does not correspond with the app interface, please visit www.kjell.com/47096->
“Support” for updated instructions.

Factory reset
Press and hold the Wifi pairing button (14) on the control panel for 5 seconds until the wifi indicator (10) flashes.

Note! If you want to install the air purifier in another wifi network, you must disconnect it from the current wifi and remove it from the app. Click on the air purifier settings panel on the app’s home screen, then the pen symbol “/•” in the upper right-hand corner. At the bottom of the page, press “Remove Device”.

Troubleshooting

The air purifier cannot connect to the app.
- Note that the air purifier only uses the 2.4 GHz frequency band. Make sure your smart device is connected to a 2.4 GHz wifi with a stable connection. If you have a dual-band router, your smart device may automatically connect to the 5 GHz wifi instead, which means it cannot communicate with the air purifier. If this happens, temporarily disable the 5 GHz wifi in your router during the installation and try again.
- The app needs access to your smart device’s location services. Make sure you have allowed access to location services while using the app.
The connection to the air purifier was lost.
- If you recently changed to a new router or renamed your network, you need to reinstall the air purifier again. Remove the product connection to your app by following the
  “Factory reset” instructions.
- Follow the “Connect to app” instructions to add the air purifier to your home network.

Cleaning and maintenance

Disconnect the power cord from the wall outlet before doing any cleaning or filter maintenance.

Pre-filter
- Vacuum or wash the filter every 15 days to remove dust. If you wash the filter in water, let it dry fully before inserting it into the air purifier.
- Cold catalyst and activated carbon filter
- Vacuum the filter every 60 days. Do not clean with water. Handle it with care and do not expose it to direct sunlight.
HEPA filter
Ventilate the HEPA filter every 60 days.
Air quality sensor
Clean the sensor every 60 days with a clean cotton swab. Remove the sensor cover (fig. 1) and clean the sensor gently with a swab (fig. 2). $cleverio- AP300-Air-Purifier-01 $6$$

Filter alarm

The air purifier has a filter alarm set to 1,500 hours. The filter indicator (12) lights up and a sound is emitted from the air purifier. Clean and check the status of the filters. If the
HEPA and carbon filters are miscoloured or covered in particles they need to be renewed. Contact the place of purchase to buy new filters.
Press and hold the Child lock button (16) for 5 seconds to reset the filter alarm.

Safety information

Leave at least 20 cm of free space around the air purifier and leave at least 30 cm of free space above it.
Do not expose the air purifier to direct sunlight and do not use it in very humid places (e.g. bathrooms).
Do not move the air purifier while it is turned on.
Do not pull the plug out with the cable. Do not touch the plug with wet hands.
Do not use the air purifier with a damaged supply cord. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified personnel to avoid a hazard.
Disconnect the air purifier from the power supply if you are not going to use it for a long time.
Do not put objects into the air outlet.
Do not place objects on top of the air purifier.
Do not use the air purifier near gas appliances, heating devices or stoves.
Turn the air purifier off if it makes strange sounds, vibrates heavily or if it starts to smell burnt.

Simplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at www.kjell.com/47096.