CLEVERIO AP100 Air Purifier User Guide

: June 4, 2024
: Cleverio

Table of Contents

Overview
USE
Troubleshooting
Safety information
Specifications
Documents / Resources

AP100 Air Purifier
User Guide CLEVERIO AP100 Air Purifier

Air Purifier
AP100
User guide
Item: 47007

Overview

CLEVERIO AP100 Air Purifier - overview

Filter
Perfume sponges
Bottom lid
Fan control button
Child lock button
Timer button
Power button
Alter status button

USE

Before first use
Flip the air purifier upside down, twist the bottom lid (3) counterclockwise, and remove the plastic bag protecting the filter (1). Put the fitter back and twist the lid to close. Connect the power cord to a wall socket. Wait 3 seconds, the Power button (7) lights up red and buzzing noise is emitted. Press the power button to turn on the purifier.
Speed settings
Press the Fan control button (4) to cycle the speed setting: low -> high -> auto -> sleep. The sleep mode is the lowest and most quiet setting and it also turns off the LED light.
Child lock
Press and hold the Child lock button (5) for 3 seconds to disable the touch controls on the air purifier. The Child lock button backlight turns off to indicate that the air purifier controls are locked. Press and hold the Child lock button again for 3 seconds to re-enable the touch controls.
Note! The air purifier can not be controlled via the app if the child lock is active.
Timer
Press the Timer button (6) to automatically turn off the air purifier after a set time. The backlight around the button light up and the timer can be set to 1, 2, 4 or 8 hours. Press the button several times to cycle.
Air quality
The built-in LED light changes color to indicate the status of the air quality around the air purifier. The indicator light can be turned off by pressing the Filter status button (8). Blue: Excellent air quality.
Green: Good air quality.
Purple: Sub-par air quality.
Red: Poor air quality.
Fitter
The Filter status button (8) flashes and noise is emitted from the air purifier to indicate when the filter needs to be replaced. This occurs after the purifier has been active for around 2000 hours. Turn off the air purifier before replacing the filter and follow the steps under “Before first use.
Press and hold the Filter Status button (8) for a few seconds to reset the timer after replacing the filter.
Perfume sponges
There are two perfume sponges (2) inside the purifier that you can apply scent to spread around the room with the help of the air purifier. Turn off the device, flip it upside down, and twist the bottom lid (3) to reach the sponges. The sponges are fastened below the cover.
Connect to app

And install the app ‘Smart Life – Smart living’ on App Store or Google Play.
Register an account in the app or log in to an existing one.
Press and hold the Fan control button (4) for 5 seconds. The backlight flashes.
Press “+” or “Add device” in the app. Go to “Small home appliances” and choose “Air purifier (Wi-Fir. The app searches for devices nearby.
Check if the Fan control button backlight is flashing and confirm in the app.
Enter the details for your 2.4 GHz wifi.

Note The pairing procedure might change due to regular app updates. If the instruction does not correspond with the app interface, please visit www.kjell.com/47007-> “Support” for updated instructions.
Factory reset
Remove the air purifier connection to your device by selecting it in the app. Edit the device by pressing the pen symbol “or in the top right corner of the app. At the bottom of the page press “Remove Device”.

Troubleshooting

The air purifier cannot connect to the app.
Make sure your smartphone or tablet is connected to a 2.4 GHz wifi with a stable connection. If you have a dual-band router, your device can automatically connect to the 5 GHz wifi. In this case, your device cannot communicate with the air purifier. Disable the 5 GHz wifi in your router during the installation and try again. The app needs access to your device’s location services. Make sure you have allowed access to location services while using the app.
The connection to the air purifier was lost.
If you recently changed to a new router or renamed your network, you need to reinstall the air purifier again. Remove the product connection to your app by following the “Factory reset” Instructions.
Follow the “Connect to app” instructions to add the air purifier to your home network.

Safety information

Simplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU declaration of conformity is available at www.kjell.com/47007

Specifications

CADR (Dust/pollen) 119 m3/h
Filtration: HEPA-13 filter, activated carbon filter, and pre-filter
Noise level: 25-50 dB
Wifi: 2.4 GHz
Power: AC 230 V, 50 Hz. Max. 30 W power consumption
Power cable, length: 1.5 meters
Size: 0228×324 mm
Weight: 2.5 kg
Effective Radiated Power: 16.59 dBm

www.cleverio.se
Box 50435 Malmo
Sweden
2022-05-10