Cleverio SA100 Smart Siren med Zigbee User Guide
- October 30, 2023
- Cleverio
Table of Contents
Cleverio SA100 Smart Siren med Zigbee
Product Information
The Smart siren SA100 is a Zigbee 3.0 enabled product that requires a gateway, the Smart Life app (free), and sensors that trigger off an alarm. It has a sound level of 75/85/105 db at 1 m distance and can be connected to a smart sensor to trigger an alarm via the Smart Life app. The siren comes with a power adapter, 1 m cable (USB-A to Micro USB), 2x screws, 2x plugs, adhesive tape, and a quick guide. It can be mounted in two ways using screws or adhesive tape.
Specifications
- Sound levels: 75/85/105 db at 1 m distance
- IOT Solution: ZigBee 3.0
- Power: DC 5 V, 1 A. Adapter is included, 1 m cable (USB-A to Micro USB)
- Mounting: Adhesive tape or screws
- Size: 78×41 mm
- Weight: 101 g
- Wireless frequency: 2400-2483.5 MHz
- Effective radiated power: 10 dBm
Specification for power supply
- Input voltage (V): AC 100–240 V
- Input AC frequency (Hz): 50/60 Hz
- Output voltage (V): DC 5.0 V
- Output current (A): 1.0 A
- Output power (W):5.0 W
- Average active efficiency (%): 74.50 %
- No-load power consumption (W): 0.048 W
Product Usage Instructions
Use
Connect to Power
- Remove the mounting bracket on the back of the siren by twisting it.
- Connect the included power adapter to the siren and to a wall socket.
- Slide the power switch to ON.
Connect to Gateway (Sold Separately)
-
Open the Smart Life app on your smart device where your Zigbee gateway is installed.
-
Select the gateway in the app.
-
Press Add + and select Siren in the gateway settings panel in the app.
-
Confirm in the app that the siren LED indicator is flashing.
Note! If the pairing fails, press and hold the pairing button on the top of the siren for 5 seconds until the LED indicator flashes and retry this step. -
Follow the app instructions. The app confirms when the sensor is added successfully, this can take up to 30 seconds.
App Operation
Connect the siren to a smart sensor that can trigger an alarm via the Smart Life app. The app is also used to change the loudness of the siren (75/85/105 db) as well as enable/disable the LED indicator lighting up if an alarm is triggered.
Mounting
The siren can be mounted in two ways:
-
Remove the bottom bracket of the siren by twisting. Mark and drill 2x 5 mm holes using the bracket as guide. Insert the included plugs and attach the bracket using the included screws. Push and twist the siren onto the bracket.
-
Attach the included adhesive tape to the back of the bracket and push the bracket onto an even surface and apply pressure, allowing the adhesive tape to stick. Push and twist the siren on the bracket.
Factory Reset
Press and hold down the Network pairing button on the siren for 5 seconds. The LED indicator starts flashing. Note! The smart siren is still connected to your gateway and visible in the app. Remove the product connection to your app by selecting the gateway in the Smart Life app and edit the settings of the siren.
Overview
Safety information
Only suitable for working temperature between -10 to 55 °C. Not for outdoor
use. Only for use in dry areas. Keep away from direct, strong sunlight.
Always disconnect the power adapter by grabbing the plug, do not unplug it by
pulling the cord.
Avoid using third-party power adapters and only use the included power
adapter.
Simplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
Full text of the EU declaration of conformity is available at
www.kjell.com/51832.
www.cleverio.se
Box 50435 Malmö
Sweden
2022-09-26
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>