CLEVERIO AF100 Air Filtering Tower Fan User Guide

CLEVERIO AF100 Air Filtering Tower Fan

Overview

Use

Installation

Place the fan on a flat and stable surface and leave at least 30 cm of free space from the air outlet. Avoid blocking the air inlet and place the fan sway from curtains and other objects that could block the inlet. Connect the power cable to a wall socket. The touch display lights up and the fan enters standby mode.

Touch display

Press the touch display to start the fan. Press and hold for 2 seconds to turn it off.
Press the touch display while the fan is running to adjust the airflow from levels 1-9.
Press and hold the touch display for 1 second while the fan is n.inning to start oscillation. Press and hold again to stop the rotation.

Directing the air flow

Hold the fan base with one hand and push the air outlet to your preferred angle. You can push it 15° forwards and/or backwards.

Remote control

Boost mode: Press the Boost button on the remote to maximise the airflow. The display shows the letter “H” and the wind speed increases. Press the Boost mode or the”+” button to exit boost mode.

Night mode: Press the Night mode button on the remote, the display shows the letter “L” and the airflow decreases to a level suitable for sleeping. Press the Night mode or the”+” button exit sleep mode.

Oscillation: Press the Oscillation button and the fan starts to rotate 80° left to right.
Press the Oscillation button again to stop the rotation.

Timer: Press the limer button on the remote to set a timer before automatically turning off. Press repeatedly to set a timer between 1-8 hours. If fan is turned off manually during a timer the setting is cancelled.

Note: Point the remote control at the touch display if you are having trouble sending commands to the fan. The fan may respond to other remotes and other devices may respond to this remote. This is due to overlapping frequencies and does not indicate the fan is faulty. To avoid this, keep the remote control away from other electrical devices during use.

Remove the piece of plastic in the battery compartment that protects the battery from being consumed prematurely in the remote control.

Change battery

Insert one CR2025 battery into the remote according to the illustration on the right. Mind the polarity.

Connect to app

1. Find and install the app ‘Smart life – Smart living’ on App Store or Google Play, or scan the QR code to the right.

2. Register an account in the app or log in to an existing one.
   Activate location services on your smart device.
   Make sure your smart device is connected to your 2.4 GHz wifi.

3. Press and hold the touch display on the fan for 5 seconds until the letter “F” lights up to activate pairing mode.

4. Press”+” and “Add Device” in the app.
   Go to “Small Home Appliances” and choose ‘Fan (Wi-FQ’.
   The app searches for devices nearby. If you are using the “Smart life – Smart living” account for the first time, enter the details for your 2.4 GHz wifi.

5. Check if the letter “F” is lit on the display, confirm in the app when asked to reset the device and select “Blink Quickly” when prompted.

6. A prompt is shown in the app when the connection is successful.

Note! The pairing procedure may change due to regular app updates. If the instruction does not correspond with the app interface, please visit www.kjell.com/47081 -> “Support” for updated instructions.

Factory reset
Press and hold the touch display on the fan for 5 seconds until an F appears.

Notel If you want to install the fan in another wifi network, you must disconnect it from the current wifi and remove it from the app. Click on the fan settings panel on the app’s home screen, then the pen symbol “ ” in the upper right-hand corner. At the bottom of the page, press “Remove Device”.

Troubleshooting

The fan cannot connect to the app.
Note that the fan only uses the 2.4 GHz frequency band. Make sure your smart device is connected to a 2.4 GHz wifi with a stable connection. If you have a dual band router, your smart device may automatically connect to the 5 GHz wifi instead, which means it cannot communicate with the fan. If this happens, temporarily disable the 5 GHz wifi in your router during the installation and try again.
The app needs access to your smart device’s location services. Make sure you have allowed access to location services while using the app.

The connection to the fan was lost.
If you recently changed to a new router or renamed your network, you need to reinstall the fan again. Remove the product connection to your app by following the “Factory reset” instructions.
Follow the “Connect to app” instructions to add the fan to your home network.

Cleaning and maintenance

Disconnect the power cable before any cleaning or maintenance.

Surface
If the surface of the fan needs cleaning dust it off with a soft, dry cloth. Then wipe it gently with diluted mild detergent and wipe any excess moisture off with a dry cloth.

Air inlet and outlet
Use a soft brush or a vacuum cleaner to remove dust from the air inlet and outlet.
Make sure that no dust accumulates at the inlet and outlet as this can affect the fan’s performance.

Remote control
Wipe the surface of the remote with a soft, dry cloth. If you are not going to use the remote for a long time, remove the battery before storage.

Filter replacement
After approximately 1000 hours of use, the HEPA filter needs to be replaced. The display lights up and the buzzer emitts sound five times when it is time to replace.

1. Turn the filter cover counter-clockwise to unlock and remove the filter.
2. Disconnect the old filter from the cover.
3. Attach the cover to the new filter and assemble it with the buckle.
4. Put it back in the fan and turn it clockwise to lock it.
   

After the filter has been changed, press and hold the Power button on the remote for 5 seconds to clear the filter alarm.

Safety information

• For indoor use only.
• Do not expose the fan to direct sunlight and do not use in very humid places.
• Keep away from children.
• Keep away from electrical devices with cooling/heating function.
• Do not use the fan in a branch outlet together with other electrical devices.
• Do not pull the plug out with the cable.
• If the supply cord is damaged, it must be replaced by the manufacturer, its  serviceagent or similarly qualified personnel to avoid a hazard.
• Disconnect the fan from the power supply if you are not going to use it for a long time.
• Make sure the air inlet and outlet are free from dust, hair and other dirt that can affect the airflow.
• Do not immerse the fan or any parts of it in water or other liquids.
• Do not use an air purifier or similar next to the fan.
• Do not use strong cleaning agents or lubricants on the appliance.

Specifications

manual.

www.cleverio.se
Box 50435 Malmo
Sweden
2022-08-31

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>