cleverio CC200 Security Camera User Guide
- June 4, 2024
- Cleverio
Table of Contents
cleverio CC200 Security Camera
Overview
Use
Mounting
You can place the camera on a table, shelf or use the included screws and
plugs to mount the camera to a wall or ceiling. Drill holes using the included
alignment sticker as a guide. Insert plugs into the drilled holes suitable for
the surface or use the included plugs. Run the cable through the cable notch
in the camera base plate. Attach the camera by aligning the camera base plate
holes to the drilled holes in the surface, insert the included screws and
tighten them.
Note! If the camera is to be mounted outdoors it must be mounted with the speaker facing downwards to avoid water and moisture entering the camera.
Connections
Connect the DC power adapter to the DC power connector on the camera. Use the
included weather proofing covers over the connectors if you are installing it
outside. Connect the DC power adapter to a wall socket. The LED indicator
lights up blue when it is starting up, changes to orange when is on and starts
flashing orange when the camera is ready to be paired with the “Smart life”
app. If the wifi signal is too weak you can connect an ethernet cable to the
LAN-port of the camera and your router.
Connect to app
-
Find and install the app ‘Smart Life – Smart living’ on App Store or Google Play.
-
Register an account in the app or log in to an existing one. Activate location services on your smart device. Make sure your smart device is connected to your 2.4 GHz wifi.
-
Press “+” or” Add device” in the app. Go to “Camera & Lock” – and select “Smart Camera (Wi-fQ”. Confirm that the LED indicator is flashing. If you are using the “Smart life – Smart living” account for the first time, enter the details for your 2.4 GHz wifi.
Note! If the LED indicator is not flashing, follow the instructions for “Factory reset” and repeat this step. -
Face the camera toward the QR code that is displayed in the app on your smart device, wait until the camera emits a sound 3 times and confirm it in the app.
-
A prompt displays on your smart device to confirm the connection was successful.
Note! The pairing procedure might change due to regular app updates. If the instruction does not correspond with the app interface, please visit www.kjell.com/51493 -> “Support” for updated instructions.
Micro SD card
Insert a Micro SD card into the Micro SD slot on the back of the camera. To
reach the Micro SD card slot you need to lift a rubber cover. A Micro SD card
is required to make recordings of events that you could not monitor in real
time.
App operation and automatic recording
Select the camera in the Smart life app home screen to access its functions
and status. In the app you can take snapshots of the current camera view,
manually start a recording as well as see previous recordings saved to the
Micro SD card. In the app you can also flip the image orientation if the
camera has been mounted upside down. The camera is equipped with a speaker
that can be used for two-way audio. Press the microphone icon to transmit
sound from your device to the camera speaker. You can also activate an alarm
signal to fend off intruders. To set up scheduled recording and access more
settings, press the button in the upper right-hand corner of the camera panel
in the app.
Connect to voice assistant
Press the “Me” button in the app, navigate to “Third-Party Voice Services” and
choose to connect the camera to either Amazon Echo, Google Home or other voice
assistant serivces
Factory reset
Lift the rubber cover on the back of the camera, press and hold the reset
button for 5 seconds. The LED indicator lights up orange when the reset is
completed and flashes orange when it’s ready to connect to app.
Note! If you want to install the camera in another wifi network, you have to disconnect it from the current wifi and remove it from the app. Select the camera on the app’s home screen, then press the symbol in the upper right-hand corner. At the bottom of the page, press “Remove Device”.
Troubleshooting
The camera cannot connect to the app.
Make sure your smart device is connected to a 2.4 GHz wifi with a stable
connection. If you have a dual-band router, your smart device may
automatically connect to the 5 GHz wifi instead, which means it cannot
communicate with the camera. If this happens, disable the 5 GHz wifi in your
router during the installation and try again. The app needs access to your
smart device’s location services. Make sure you have allowed access to
location services while using the app.
The connection to the camera was lost.
If you recently changed to a new router or renamed your network, you need to
reinstall the camera again. Remove the product connection to your app by
following the “Factory reset” instructions. Follow the “Connect to app”
instructions to add the camera to your home network.
Safety information
Don’t open or modify the device in any way, this should only be done by a qualified technician due to the risk of electric shocks and/or short circuit. The mains plug is used as the disconnect device, therefore the mains plug shall remain readily operable.
Simplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
Full text of the EU declaration of conformity is available at
www.kjell.com/51493.
Specifications
www.cleverio.se Box 50435 Malmo Sweden 2022-09-26
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>