COOPER LIGHTING IB50603822 Galleon LED Floodlight Instruction Manual
- June 14, 2024
- COOPER Lighting
Table of Contents
IB50603822
Streetworks
Installation Instructions – Galleon Wall Companion BB/GAW Back Box
IMPORTANT: Read carefully before installing product. Retain for future reference. Failure to comply with these instructions may result in death, serious bodily injury and property damage.
WARNING
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation
and maintenance of this product must be performed by a qualified electrician.
This product must be installed in accordance with the applicable installation
code by a person familiar with the construction and operation of the product
and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting
installation or attempting any maintenance. Disconnect power at fuse or
circuit breaker.
Risk of Fire- Refer to product label for specific minimum supply conductor
requirements. Risk of Burn- Disconnect power and allow fixture to cool before
handling or servicing.
Risk of Personal Injury- Fixture may become damaged and/or unstable if not
installed properly.
DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability
for damages or losses of any kind that may arise from the improper, careless,
or negligent installation, handling or use of this product.
NOTICE: Green ground screw provided in proper location. Do not relocate.
ATTENTION Receiving Department: Note actual product description of any
shortage or noticeable damage on delivery receipt. File claim for common
carrier (LTL) directly with carrier. Claims for concealed damage must be filed
within 15 days of delivery. All damaged material, complete with original
packing must be retained.
Safety: This product must be wired in accordance with the National
Electrical Code and applicable local codes and ordinances. Proper grounding is
required to insure personal safety. Carefully observe grounding procedure
under installation section.
APPLICATIONS: This Back Box is designed for use with the Axcent (AXC)
light fixture or the Galleon Wall Companion (GWC or GAW) fixtures. It must be
stored in a dry location prior to installation. Do not expose Back Box to
rain, dust, or other environmental conditions prior to installation. Best
results will be obtained if installed and maintained according to the
following instructions.
Note:
These instructions do not claim to cover all details or variations in the
equipment, procedure, or process described, nor to provide directions for
meeting every possible contingency during installation, operation, or
maintenance. When additional information is desired to satisfy a problem not
covered, please contact your nearest representative.
Note: Specifications and dimensions subject to change without notice.
Installation
This Back Box assembly has been shipped complete. Please follow the installation instructions.
BB/GAW Back Box is for wall mounting only
Tools Required:
• #2 Phillips head screwdriver, torque wrench, tool for mounting hardware
(supplied by others).
- Determine the power conduit entry side and remove the conduit plug (1/2” NPT). Attach the BB/GAW Back Box to the wall by the 4 mounting feet. Use ¼” dia screw hardware that is designed for the mounting surface (wood, cement, etc). FIGURE 1. Figure 1.
- Run power wires into the BB/GAW Back Box through the open ½” NPT hole. Use green ground screw for power ground and fixture ground. FIGURE 1.
- Locate wedge plate and orient with the label showing the up orientation. FIGURE 2. Figure 2.
- Attach the wedge plate to the BB/GAW Back Box with provided hardware as shown in FIGURE 3. Torque screws to 20 in-lbs. Figure 3.
- Change out the galvanized top bracket on the top of the GAW luminaire with the black bracket (supplied with Back Box). Note that the black wedge bracket and wedge plate have extra corrosion resistance coating. Torque the screws to 20 in-lbs. FIGURE 4. Figure 4.
- Hang the luminaire from the wedge plate using the cable hanger and the screw in the wedge plate (FIGURE 2 AND 4).
- With the luminaire hanging from the cable hanger, make the power wire connections in accordance with luminaire instructions.
- Push all wire connections through hole in wedge plate and into Back Box. Lift the luminaire onto the wedge plate and make sure it is hooked on to the black wedge bracket. Ensure that the luminaire supply leads are not pinched between the wedge plate and the housing.
- Tighten the two setscrews on the luminaire per the luminaire instructions.
FCC Statement
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Warranties and Limitation of Liability
Please refer to www.cooperlighting.com for
our terms and conditions.
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2022 Cooper Lighting Solutions
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IB50603822
October 7, 2022Cooper Lighting Solutions is a
registered trademark.
All trademarks are property
of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>