LLOYD S LC-1330 Smart Video Doorbell User Guide

Smart video doorbell
Brand: Lloyd´s
Model: LC-1330

LC-1330 Smart Video Doorbell

Lloyd’s ® helps you make your Home a Smart Home Take control from one single app and transform your spaces into safe, efficient, comfortable and fun places
QUICK GUIDE
PLEASE READ THE INSTALLATION GUIDE BEFORE OPERATING THE PRODUCT
“Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may be caused by undesired operation”.

Characteristics

• Monitoring and control from your smartphone
• Motion detection and low battery notifications
• Cloud storage for motion detection recordings (requires subscription)
• 1080P FHD resolution
• Supports a memory card up to 64 GB
• No HUB required
• Monitor the battery status from the app
• Two-way audio
• Night vision
• Multi-user
• 100% wireless, powered by 2 rechargeable batteries type 18650 (included)
• USB cable included for recharging batteries, adapter not included (recommended to use an adapter with a 5 Vdc 1500 mA output)
• Material: ABS plastic
• Viewing angle: 160°
• PIR motion detection range: ≤ 3 meters
• Approximate battery lifespan: 3 to 6 months (10 detonations per day)
• Operating temperature: -10ºC ~ +50ºC
• Relative humidity: ≤80% RH
• Standby power consumption: 20 uA
• Operating power consumption: 170 mA
• Compatible with Amazon Echo Show and Google Nest HUB virtual assistants
• Compatible with Siri Shortcuts through routines created from the app
• TV watching through Google Chromecast and Alexa Fire TV Stick devices with voice remote control
• Allows the creation of routines that trigger actions in other Lloyds smart products

Contents

Diagram

Do not expose this product to dripping or splashing water and never place objects filled with liquids ( such as glasses) on top of it.

1. Light sensor: it will detect the state of the ambient light. When the ambient light falls below 2 Lux, the infrared LEDs will be activated automatically.

2. Infrared LEDs (x6): if the ambient light is not sufficient, these LEDs will be activated to improve the brightness of the image.

3. Microphone

4. Call button

5. Speaker

6. Lens

7. LED indicator:
   • Flashing blue light: the video doorbell is in setup mode.
   • Red light on: there is a failure in the connection to the Wi Fi signal.
   • Blue light on: the device is connected to the Wi Fi network.=

8. PIR (infrared sensor): detects movement in front of the device to trigger notifications.

9. Reset button: to reset the device, press and hold this button for 5 seconds.

10. Battery compartment: operates with 2 rechargeable batteries type 18650 (included).
    ATTENTION: Danger of explosion if the batteries are not replaced correctly. Batteries installed in this device must not be exposed to excessive heat such as sunlight, fire or the like. Dispose of batteries in specified collection sites, do not throw them in the garbage.

11. USB port: for recharging batteries via USB cable.

12. Holes for mounting bracket attachment.

13. Memory card slot (not included). To locate it, the battery compartment cover must be removed.

Wall mount Mark the holes on the wall where the video doorbell is to be placed, using the slots on the mounting bracket as a guide, then drill over the marks and insert the anchors.
Attach the mounting bracket using the screws, then place the video doorbell on the bracket by carefully sliding it from the top. Secure it to the bracket by fastening the bottom part with two screws.
WARNING: this unit must be securely anchored to the floor/wall according to the installation instructions to avoid any damage

Before getting started

Make sure your smartphone has iOS 10.0 or higher or Android™ 4.4 or higher. Check your network and make sure it is connected to a 2.4 GHz Wi Fi channel.

https://smartapp.tuya.com/smartlloyds

Download the Lloyds Smart app from the appStore or Google Play or scan the following QRcode with your smartphone.

Registration and access

Launch the Lloyds Smart app. To regis- ter, click on “Sign Up” (1), to continue, click “Agree,” choose your country and enter an email address, then click “Get Verification Code” (2). Enter the code sent to your email (check inbox or spam) (3), set a password, and click “Done” (4). Or log in directly if you already have an account.

Add device

Start the Lloyds Smart app on your smartphone, select “+” (upper right corner) (1), choose the type of device that you want to add, in this case, go to “Security” (2), then select “Door Bell” (3). Remove the back cover of the video doorbell and install the batteries into the compartment.
Once the batteries are installed, press the “Reset” button for 5 seconds until the LED indicator flashes rapidly, or you hear “System reset” and then “The camera is now ready to begin pairing”, confirm in the app,
(4) then click “Next” (5).Enter your Wi Fi network information and password, then click “Next” (6). Place the camera between 15 and 20 cm in front of your smartphone to scan the QR code and click “I heard a prompt” (7) once you hear it. Once the device is configured, you can change the name (8). Finally, click on “Done”(9).
NOTE:
Make sure that the Wi Fi password you enter is correct and that the device is close to the modem during the process. After completing the setup, find and select the device in the list (10) to monitor and control it through the app from wherever you are. Only internet connection is required.

Device control

1. Change resolution
2. Battery level
3. Full screen
4. Image capture
5. Talk
6. Video recording
7. Drop down / Hide menu
8. Video playback from the
memory card
9. Photos and videos saved
on the smartphone
10. Edit panel| 11. More functions
12. Sound
13. Enlarge / reduce screen size
14. Signal quality (SQ)
15. Enable / disable motion detection alarm
16. Interface theme selection (dark mode / light mode)
17. Alarm message history
18. Cloud storage
19. Create smart routines
20. Characteristics
---|---

NOTE:
You will be able to access the recorded data by motion detection in the cloud even if the camera is offline or if it has been lost or stolen (subscription required).
In “More functions” (interface upper right corner), you will be able to rename the device, share control of it with family and acquaintances, access information, create groups, update the firmware or delete the device.

Safety warnings for the installation of the additional chime

1. Install the chime according to the instructions in this manual to avoid any malfunction or damage.
   NOTE:
   Connect the chime to electrical power in a convenient location for easy operation and disconnection. Ventilation should not be impeded by covering ventilation openings with objects, such as newspapers, tablecloths, curtains, etc.

2. The chime is designed for indoor use only.

3. The chime cannot be repaired by the user, as there is a risk of electric shock if the device is opened.

4. Do not expose it to rain or splashing liquids or immerse it in water.

5. Do not install the device near heat sources or expose it to high temperatures.

6. Never use chemicals or wet cloths to clean the unit. Use only a dry, clean, soft microfiber cloth.

Chime diagram

Chime characteristics

• Sensitivity: -112 dbm
• Frequency: 433 MHz
• Power consumption in standby mode: 10 mW
• Volume: 5 levels (maximum: 100dB / minimum: mute)

Installation and setup of the chime

1. Connect the chime to the power supply.

2. Select the melody: this chime has 50 melodies.

3. When the chime is connected, press the “Melody selection” button repeatedly until you find the tone of your preference.

4. Press the “Volume Select” button to choose the desired level of modulation.

5. To link the chime to the video doorbell, press and hold the Volume selection button for 5 seconds until the LED indicator lights up, then press the “Call button” on the
   video doorbell to synchronize.

6. Under the same procedure, you can link the chime to another video doorbell and/or you can pair two or more video doo bells to the same chime.

7. If you want the chime to play a different melody for each video doorbell, be sure to select the desired tone in the chime before performing the linking process.

8. To unlink the chime from the video doorbell, disconnect it from the power supply. Before switching it back on, press and hold the Volume selection button and do not release it for 5 to 10 seconds even after switching it on. When the indicator LED lights up, the device will reset to its factory settings.

NOTE:

• It is recommended to link the chime before setting up your video doorbell in the app.
• The name that you assign to the device will be the one that you use for voice commands with Google and Amazon Alexa assistants.

How to configure with Siri Shortcuts

The Lloyd’s smart products are compatible with Siri Shortcuts through routines created from the app. For configuration details, scan the following QR code with your smartphone: Make sure your smartphone has iOS 12 or higher.

https://lloydscorp.com/qr/siri-access/

How to connect to Google Home:

How to connect to Google Assistant:

1. Download and launch the Google Home app, previously configured with your Gmail account and your Google Assistant-enabled device.
2. Click on the “+” icon, choose “Set up Device,” then in the “Works with Google” section, click on the search bar and type in Lloyds Smart. When you get the icon, click on it. Enter your Lloyds Smart account and click on “Link now”. Then press on “Authorize” and wait a few seconds.
3. Once you have linked Lloyds Smart, the devices added to your account will be displayed, click on “X” (top left corner) and return to the main screen. Now you can control your Lloyd’s Smart devices using just your voice with Google.
   NOTE:
   You can rename the devices from the Lloyds Smart app to control them with voice commands. Every time you rename the devices, say: “Hey Google, sync devices” or update from the Google Home app.

Try saying “Hey Google” followed by one of the following commands:
“Ok Google, show main entrance on TV”
“Ok Google, show main entrance”

• Watch on TV (Google Chromecast required) or Google Nest HUB assistant
  “Google and Chromecast are trademarks of Google LLC. Requires a compatible TV with an HDMI port and a compatible mobile device. Learn more at g.co/cast/req.”
  How to connect to Amazon Alexa:

  1. Download and access the Amazon Alexa app, previously configured with your email account and your virtual assistant.
  2. Click on the option “Skills & games”, then in the search bar type Lloyds Smart. When you get the icon, click on it. Then press the “Activate to use” button.
  3. Enter your Lloyds Smart account and click on “Link Now” and finally “Authorize”. You will get the message “Linked successfully”, click on “Close” and wait a few seconds.
  4. Click “Detect devices” to find the smart devices. Now you can ask your assistant to control them by voice commands.
     NOTE:
     You can rename the devices from the Lloyds Smart app to control them with voice commands. Every time you rename the devices, say: “Alexa, sync devices” or update from the Amazon Alexa app.

Voice command examples:
“Alexa, show main entrance”
“Alexa, show street”
*View on TV (Alexa Fire TV Stick with voice remote control required) or on Amazon Echo Show assistant
NOTE:
The Google Home and Amazon Alexa Apps are constantly being updated. For more information, please refer to their user manuals.

Technical specifications

Video doorbell: 5 Vdc 0,5 A (2 lithium batteries 3,7 Vdc 5 200 mAh)
Included chime: 100 – 240 V~ 50/60 Hz 15 mA
This device is compatible with the following apps

IMPORTED BY:
ZUTTO TECHNOLO GIES, S. A. DE C.V.
R.F.C.: ZTE161017KT6
No. 505 Interior 1602,
Col. Granada, C.P. 11520. Miguel Hidalgo
Ciudad de
Tel. / Phone: 55 6844 7575

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>