SKYDANCE R11 Ultrathin Touch Slide RF Remote Controller Instruction Manual
- June 14, 2024
- SKYDANCE
Table of Contents
SKYDANCE R11 Ultrathin Touch Slide RF Remote Controller
Product Information
The Ultrathin Touch Slide RF Remote Controller is available in various models: R11, R12, R13, R14, and R10. It is designed for controlling single color, dual color, RGB, RGB+W or RGB+CCT LED controllers. The remote operates wirelessly with a range of up to 30 meters. It is powered by a CR2032 battery and features an ultra-sensitive color adjustment touch slide. The remote can be easily stuck on any metal surface or back holder using the magnet on the back. It is available in both white and black colors.
Product Usage Instructions
- Insert a CR2032 battery into the remote.
- Ensure that the LED indicator light on the remote is functioning.
- To control the LED controller, touch and slide your finger on the sensitive color adjustment area of the remote.
- For single color LED controllers, slide your finger to adjust the brightness level.
- For dual color LED controllers, slide your finger to adjust between the two colors.
- For RGB, RGB+W or RGB+CCT LED controllers, slide your finger to adjust the desired color combination.
- If you have multiple LED controllers, each remote can be paired with one or more receivers. Follow the pairing instructions provided with your LED controller to establish the connection.
- The remote operates on a frequency of 2.4GHz, ensuring a reliable wireless connection with a range of up to 30 meters.
- The standby time of the remote is optimized for power efficiency.
- To fix the remote on a metal surface or back holder, use the magnet on the back of the remote for easy attachment.
Ultrathin Touch Slide RF Remote Controller
Model No.: R11, R12, R13, R14, R10
Touch color slide/1-5 color /Wireless remote 30m distance/CR2032 battery/Magnet stuck fix
Features
- Apply to single color, dual color ,RGB, RGB+W or RGB+CCT LED controller.
- Ultra sensitive color adjustment touch slide.
- Each remote can match one or more receiver.
- CR2032 battery powered.
- Operate with LED indicator light.
- Magnet on the back which can be easily stuck on back holder or any metal surfaces.
- White & Black available
Technical Parameters
Input and Output
Output signal| RF(2.4GHz)
Working voltage| 3VDC(CR2032)
Working current| <5mA
Standby current| <10μA
Standby time| 1 year
Remote distance| 30m(Barrier-free space)
Safety and EMC
EMC standard (EMC)
| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certi cation| CE,EMC,LVD,RED
Package
Size| L156 x W48 x H22mm
Gross weight| 0.075kg
Environment
Operation temperature| Ta: -30 OC ~ +55 OC
Warranty
Warranty| 5 years
Mechanical Structures and Installations
To fix the remote, three options are offered for selection:
- Option 1: stuck the remote on any metal surfaces directly.
- Option 2: fix the remote’ back holder on the wall with two screws.
- Option 3: adhere the remote’ back holder to the wall with paster.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match,
The LED indicator fast flash a few times means all matched remotes were
deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Key function
R11 1 zone dimming remote
R12 1 zone CCT remote
R13 1 zone RGB remote
R10 1 zone RGB+CCT
R14 1 zone RGBW remote
- Short press for On/Off.
- Press and hold 1-6s for brightness dimming.
- When light is on, fast press 2 times for shift between RGB and CCT touch slide.
Safety information
-
Read all instructions carefully before you begin this installation.
-
When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. -
If no response from the receiver, please re-match the remote.
-
Gently handle remote, beware of falling.
-
For indoor and dry location use only.
FCC Warning
19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>