eufy SECURITY S120 Solar Wall Light Cam User Guide

: June 14, 2024
: eufy SECURITY

Table of Contents

AT A GLANCE
WHAT’S INCLUDED
CHARGING THE CAMERA
SETTING UP
MOUNTING
- Location Height
- Mount the Camera
SAFETY
NOTICE
IC RF Statement
CUSTOMER SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

eufy SECURITY S120 Solar Wall Light Cam

AT A GLANCE

① Solar Panel
② Camera
③ LED Indicator
④ Microphone
⑤ USB-C Charging Port
⑥ SYNC Button
⑦ Speaker

WHAT’S INCLUDED

S120 Solar Wall Light Cam
Model: T81A0
Mounting Bracket
Mounting Screws
Camera Fixing Screw
Adapter for External Solar Panel
Quick Start Guide

CHARGING THE CAMERA

Charging The Camera

A standard USB-C to USB-C charging cable (not included) and AC adapter (not included) are required for charging.Fully charge before first use.

SETTING UP

Download and install the eufy Security app, and sign up for an account.
|
---|---
Follow the on-screen instructions to add your Solar Wall Light Cam.

MOUNTING

Select a Location

The camera can be mounted on a wall or similar surface. Select a location where the solar panel will not be blocked by obstacles such as a roof or leaves.
Mounting

If it isn’t possible to completely avoid the solar panel being blocked by obstacles, try to allow as much exposure to sunlight as possible.
Pay attention to battery management via the app to make sure your device receives enough power to continue operating. If your Solar Wall Light Cam does not receive enough power to continue operating, it can be charged manually, or an additional solar panel (with adapter for external solar panel) can be connected and placed in a location with sufficient sunlight to stay powered.

Location Height

We recommend mounting 2 m – 2.5 m (6.6 ft – 8.2 ft) above ground level.

To maximize solar panel efficiency and the camera field of view, select a location where the camera receives plenty of sunlight.
Location Height

Mount the Camera

Mark the mounting points on the wall or surface where drilling will be required, using the mounting bracket as a template.
Drill holes in the wall or surface, then insert the expansion anchors into the holes.
This step applies if mounting onto hard surfaces such as brick or concrete. For soft surfaces such as wood, skip this step.
Screw the mounting bracket onto the wall.
Slot the camera onto the mounting bracket and make sure it is attached securely.
Insert and tighten the camera fixing screw at the bottom of the camera.

SAFETY

Do not use the product in an environment where the temperature is too high or too low. Never expose the product to wet environments.
The suitable temperature for devices and accessories is -20°C to 50°C (Charging temperature is 0°C to 40°C).
It is recommended to supply the device in an environment with a temperature that ranges from 5°C to 25°C.
Unless specifically indicated that it is safe to do so in the user guide or instruction manual, do not use this device in an environment that exceeds the recommended low or high temperature.
Unless specifically indicated that it is safe to do so in the user guide or instruction manual, avoid exposing your device to direct sunshine or excessively wet environments.
When supplying power, place the device in an environment that has a normal room temperature and good ventilation.
The light source contained in this luminaire should only be replaced by the manufacturer, its service agent or a similarly qualified person.

CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED. DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.

Warning:

Replacing a battery with an incorrect type may bypass safeguards and create danger;
Disposal of a battery in a fire or other source of significant heat, or by crushing, or cutting, may result in an explosion as well as leakage of flammable liquids and gases;
Leaving a battery in an extremely hot environment may result in an explosion as well as leakage of flammable liquids and gases;
A battery subjected to extremely low air pressure may result in an explosion as well as leakage of flammable liquids and gases.

NOTICE

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible or compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3)Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm.

Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
The following importer is the responsible party:
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004
Telephone:1-800-988-7973

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.”

This Class B digital apparatus complies with Canadian ICES-003.

IC RF Statement

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

Declaration of Conformity

This product complies with the radio interference requirements of the European Community.

Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site: https://uk.eufylife.com/.

This product complies with the radio interference requirements of the United Kingdom.

Hereby, Anker Innovations Limited declares that this product is in compliance with Radio Equipment Regulations 2017(SI2017/1206). The full text of the UK declaration of conformity is available at the following internet address: https://uk.eufylife.com

RF exposure information:

The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use product that maintains a 20cm distance between the device and the human body.

Frequency bands and power as below:

Function	Bands	Operation Frequency	Max. Power
Wi-Fi	2.4GHz	2412-2472MHz	EIRP 19.94 dBm

The following importer is the responsible party (contract for EU matters):
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807
Munich, Germany
The following importer is the responsible party (contract for UK matters):
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

CUSTOMER SERVICE

12-month limited warranty
(US) +1 800-988-7973
support@eufy.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road,
Mongkok, Kowloon, Hong Kong
@EufyOfficial
@EufyOfficial
@EufyOfficial

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.