POWER-LITE CP10-16W-CC LED Circular Light Panel Instruction Manual
- May 16, 2024
- POWER-LITE
Table of Contents
POWER-LITE CP10-16W-CC LED Circular Light Panel
Product Information
LED CIRCULAR PANEL – CP10-16W-CC
The LED Circular Panel CP10-16W-CC provides certainty at the speed of light. It is a high-quality luminaire that offers efficient and reliable lighting for various applications. The light source in this luminaire is not replaceable, so when it reaches itsend of life, the entire luminaire should be replaced.
Important Safety Instructions
- Please keep these instructions for future reference.
- For non-replaceable light sources, the entire luminaire should be replaced when the light source reaches its end of life.
Installation Procedure
WARNING: Follow these safety precautions during installation:
- Switch off the power supply before installation.
- Switch on the power supply only after complete installation and examination of the circuit.
- Installation and maintenance should be done by a professional electrician only.
Make sure to turn off the power supply before starting any installation. Read the instructions thoroughly and ensure that you have all the necessary tools and accessories to complete the installation correctly.
Surface Mounted Installation
Step 1:
Take out the lamp and accessory pack from the box.
Step 2:
Connect the wires with L (Line) and N (Neutral), and perform insulation treatment.
Step 3:
Slide the spring to the edge and remove them.
Step 4:
Aim the groove at the installation bracket, then rotate the lamp.
Step 5:
Rotate the bracket clockwise until it fixes tightly with the lamp groove.
Recessed into Ceiling
Step 1:
Open a hole with a size of 65 mm~205 mm.
Step 2:
Rotate the bracket clockwise until it fixes tightly with the lamp groove.
Step 3:
Adjust the snap to a proper cutout size.
Step 4:
Choose the preferred CCT (Correlated Color Temperature) or power by using the slide switch. Ignore this step if the function is not available.
Step 5:
Connect the wires with L (Line) and N (Neutral), and perform insulation treatment.
Step 6:
Hold back the spring clip, then push the downlight into the hole.
Following these installation instructions will ensure proper setup and usage of the LED Circular Panel CP10-16W-CC. For any further assistance or troubleshooting, refer to the user manual or contact our customer support.
Important Safety Instructions
To ensure correct function and safety, please read and follow all instructions carefully before using the product:
- Turn off the power supply before installation or before doing any maintenance work.
- Do not install any luminaire near the heat source.
- IP grade please refer to the product label, only IP54 can be used in damp locations.
- Do not exceed the nominal supply voltage or amperage ratings.
- The dimmable version could be compatible with a wide range of recommended TRIAC dimmers.
- All wiring and installation of the light fitting must adhere to local and national wiring rules.
- Take care not to pull any electrical wires during unpacking as this may damage the connection.
- Lay out all the components on a smooth surface and make sure there are no components missing before assembling.
- To avoid injury or damage to the fitting, please ensure that power leads and screws are secure before connecting the power.
- Please keep instructions for future reference.
For non-replaceable light sources:
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
Installation Procedure
WARNING
- Switch off before installation.
- Switch on only after complete installation and examination of the circuit.
- Professional electrician for installation and maintenance only.
Turn Off the power supply before starting any installation. Read the instructions & check you have all the tools & accessories to complete the installation correctly.
Surface Mounted Installation
Step 1
Take out the lamp and accessory pack from the box.
Step 2
Slide the spring to the edge and remove them.
Step 3
Knock in the plastic anchor into the ceiling, fix the bracket with a screw.
Step 4
Choose the preferred CCT or power by slide switch. (Ignore this step if without the function)
Step 5
Connect wires with L, and N, and do insulation treatment.
Step 6
Aim the groove at the installation bracket, rotate the lamp clockwise until it is firmly fixed, and turn on.
Recessed into Ceiling
Step 1
Open a hole with size 65mm~205mm
Step 2
Rotate the bracket clockwise until it is fixed tightly with the lamp groove.
Step 3
Adjust the snap to a proper cutout size; Choose the preferred CCT or power by slide switch. (Ignore this step if without the function)
Step 4
Connect wires with L, and N, and do insulation treatment.
Step 5
Hold back the spring clip then push the downlight into the hole.
Step 6
Connect wires with L, and N, and do insulation treatment.
- 1800 909 306
- nedlandsgroup.com.au
- [email protected].