POWER-LITE BLP16W-30/60-CC LED Backlit Panel Instruction Manual

: October 30, 2023
: POWER-LITE

Table of Contents

BLP16W-30/60-CC LED Backlit Panel
Product Information
Safety Instructions
Product Usage Instructions
PANEL
Recessed Installation | Method 1
Recessed Installation | Method 2
Safety Instructions
Installation Procedure
Surface Mount Installation
Pendant Installation
1800 909 306
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BLP16W-30/60-CC LED Backlit Panel

Product Information

The LED Backlit Panel is a type of light fixture that provides a bright and energy-efficient lighting solution. It comes in four different models: BLP16W-30/60-CC, BLP36W-120/30-CC, BLP36W-60SQ-CC, and BLP45W-120/60-CC. The panel is designed for recessed installation, and there are two methods available for this type of installation. The panel comes in different sizes, and the cutout size needed for installation depends on the panel size. Clips should be purchased separately as an accessory.

Safety Instructions

Before installing the LED Backlit Panel, make sure that the mounting surface or structural member used for installation can support the weight of the panel. Also, ensure that the circuit is switched off before starting the installation and switched on only after complete installation and examination of the circuit. The lamp inspection should be done before installation to ensure that the fitting is not warped.

Product Usage Instructions

Choose the appropriate recessed installation method based on your preference.
Check the cutout size required for your panel size from the table provided in the user manual.
If necessary, purchase clips as an accessory.
Ensure that the mounting surface or structural member used for installation can support the weight of the panel.
Switch off the circuit before starting the installation.
Inspect the lamp before installation to ensure that it is not warped.
Select the appropriate color temperature before installation using the slide switch with corresponding color temperature.
Install the panel according to the chosen method and spacing requirements provided in the user manual.
Switch on the circuit only after complete installation and examination of the circuit

It is important to note that the input wire diameter should be 0.75mm2, and product modification and improper installation are not valid for warranty. Additionally, the light source contained in this luminaire should only be replaced by the manufacturer or a qualified person.

PANEL

BLP16W-30/60-CC
BLP36W-60SQ-CC
BLP36W-120/30-CC
BLP45W-120/60-CC

Recessed Installation | Method 1

Recessed Installation | Method 2

Cutout Size

Panel Size| Cutout| Panel Size| Cutout
295x295mm| 270x270mm| 620x620mm| 590x590mm
295x595mm| 270x570mm| 295x1195mm| 270x1170mm
595x595mm| 570x570mm| 595x1195mm| 570x1170mm

Clips should be purchased separately as an accessory

Safety Instructions

Basic safety precautions should always be followed when installing, including the following:
Read instructions carefully before installing.
This LED Panel requires professional installation and maintenance.
The power supply of the LED Panel should be powered by a dedicated external LED driver.
Disconnect the power supply before installing or maintenance.
Make sure the wires have been properly connected before powering on the device.
Ensure the product has enough space for heat dissipation.
Ensure the luminaries are never covered by any heat insulation mat or slim layer material at anytime.
IP40 for indoor use only, not for damp locations.
Storage Conditions: Cool & dry conditions.
Ambient Temperature: -10° to +40°. Avoid direct sunlight.
Please ensure the LED driver is situated either on back of fitting or suspended above fitting, and that the driver is clear of any insulation.

Installation Procedure

WARNING

Switch off before installation.
Switch on only after complete installation and examination of the circuit.

CAUTION: Make sure that the mounting surface or structural member used for installation can support the weight of LED Panel.

Please select colour temperature before installation, see below picture. Choose colour by slide switch with corresponding colour temperature. Lamp inspection before installation:
Take out the fitting from the box and place it on a flat table. If the fitting is warped, please adjust the fitting by following the steps below before installation:

Press the opposite angles at the same time;
Press the other two opposite angles at the same time, make sure the four angles are flat, then start the installation.

Installation Spacing

RISK OF FIRE – Required clearance from structural members and building elements

SCB=25mm HCB=25mm MIC=0mm SCI=0mm

HCB: Height clearance to building element MIC: Minimum insulation clearance

SCI: Side clearance to insulation

SCB: Side clearance to building element

WARNING – RISK OF OVERHEATING OR FIRE IF THE CLEARANCE DISTANCES ARE COMPROMISED

Warning :
Input wire diameter 0.75mm ;2
Product modification and improper installation are not valid for warranty!
The light source contained in this luminaire shall only be replaced by the manufacturer or a qualified person.