CLOUDY BAY B0B6RN1G3Q 6 Inch Smart Wifi LED Recessed Lights Instruction Manual
- June 14, 2024
- Cloudy Bay
Table of Contents
CLOUDY BAY B0B6RN1G3Q 6 Inch Smart Wifi LED Recessed Lights
6-INCH SMART
LED RECESSED DOWNLIGHT
- GENERAL: All electrical connections must be by local and National Electrical Code (N.E.C) standards. If you are unfamiliar with proper electrical wiring connections, contact and obtain the services of a qualified electrician. Use UL or! EC-approved wire only for input/output connections.
- Remove fixture and mounting components from the box, and make sure that no parts are missing, by referencing the illustration in the illustration instructions.
- This retrofit assembly is accepted as a component of a led luminaire where the suitability of the combination shall be determined by csa or Canadian authorities having jurisdiction. This device is not intended for use with emergency exits.
XX= WH, ORB or other finish color
- Turn power off before installation, inspection, or removal. Use all necessary precautions while performing this procedure.
- Properly ground electrical enclosure. THE OUTLET BOX MUST BE PROPERLY GROUNDED.
- DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS, OTHERWISE, SAFETY WILL BE COMPROMISED.
- This Integrated LED Fixture has no lamp/bulb to replace.
WARNING: RISK OF ELECTRIC SHOCK. DISCONNECT THE MAIN POWER AT THE FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.
PRODUCT CARE
After Sales Service
- Please discontinue using the product right away if the product shows any visible defect and contact customer service.
- lf there is any problem with our lights for non-human reasons, please contact customer service, and we will send you a brand-new replacement without the need to return goods or a full refund.
- lf you are not completely satisfied with the product after installation but prefer not to disassemble it, contact us right away, and we will provide comparable compensation.
WARNING- RISK OF FIRE OR ELECTRIC SHOCK
- LED Ultra Slim Panel kit installation requires knowledge of luminaire electrical systems.
- If not qualified, do not attempt installation. Contact a qualified electrician.
- Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the panel kit does not exceed the input rating of the luminaire.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- The inside of the ceiling must be waterproof.
Component list
ASSEMBLY
User Manual and Voice Guideline
Note: This product is a smart light, using Direct Digital Controls rather than triac dimming. Here is two dimming way for your reference:
- Download Cloudy Bay’s APP, go to the product group or single product page, and adjust the brightness and CCT of white light or colour light on the control panel; you can also go to the home page, click product group or single product’s common function, adjust brightness and color temperature
- Control with a smart voice device such as Google Assistant or Amazon Alexa if you have installed it successfully.
If you only have a dimmer at hand, set it to the highest level only. If the light performance is not good, we strongly advise you to change it to a regular switch.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference, and This device must accept
any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and according to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiver antenna.
- Increase the separation between the equipment and the receiver.
- Install the product onto on a circuit different from that to which the receiver is connected.
- Consult with the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes made to the electronics circuit will void this equipment’s compliance with Part 15 of the FCC Rules and should not be operated.
INSTALLATION INSTRUCTIONS
- Cut a round hole in 0 6-1 /4 inches with a template in the package. (Fig.1)
- Insert a flat screwdriver’s blade into the knock-out hole, and swing left and right until the metal plate falls. (Fig.2)
- Put wire clamp into knock out hole. (Fig.3)
- Open connection box by pulling up the cover (Fig.4)
- Insert the white supply wire (neutral) into the quick wire connector with the preassembled white fixture wire. Insert the black supply wire (hot) into the quick wire connector with the preassembled black fixture wire. Insert the supply ground wire into the quick wire connector with the preassembled ground wire. Make sure all connections are secure, and tuck all wires into the junction box. Put on the cover of the junction box(Fig.4)
- Connect the low-voltage cable to the light kit – the arrows on the male and female parts of the connector between the driver and the fixture should match. (Fig.5)
- Squeeze both TORSION SPRINGS arms together and insert them into the above ceiling. (Fig.6)
- Installation is completed. (Fig.7)
- Set up products according to user manual and voice guideline
- Please contact the seller through E-mail for assistance or refer to troubleshooting if you have a problem using our products.
QUESTIONS? COMMENTS?
- SUGGESTIONS? COMPLAINTS?
- Please contact us through smart@cloudybaylighting.com or info@cloudybaylighting.com We will do our best to make it right for you. Thank you very much!