eufy SECURITY E340 Floodlight Camera User Guide

QUICK START GUIDE
Floodlight Cam E340

SAFETY INSTRUCTIONS

• Check your local laws for installation. If you are outside of North America, installation and wiring must be performed by a licensed electrician.

• This manual is for informational purposes only. Working with electricity can be dangerous, so it’s important to take proper safety precautions.
  Hire a licensed electrician if you are not comfortable or inexperienced with the processes and tools described.

• Disconnect power at the fuse or circuit breaker before installation.

• Do not install the product near flammable surfaces.

• To avoid the risk of shock, injury, or death, always be cautious when working with electricity.

• Make sure the floodlight camera is properly grounded.

• The floodlight camera must be mounted on a wall or under a cornice.

WHAT’S IN THE BOX

WHAT YOU NEED (Not Provided)

AT A GLANCE

1. Floodlight
2. Speaker
3. Motion Sensor Component
4. System Indicator
5. Telephoto Camera
6. Wide Angle Camera
7. Infrared Component
8. Power Input (For Quick Setup)
9. SYNC Button
10. microSD Card Slot Insert a microSD card* (not provided) to store recordings
11. Mounting Bracket
12. Mounting Base

• Use at least a Class 10 microSD card with a maximum of 128 GB.

SETTING UP THE SYSTEM

1. Download and install the eufy Security app, then sign in or create an account.
2. Power on the floodlight camera by using the USB-C charging cable and a power adapter (5V/1A, not provided).
3. Tap + in the app and follow the in-app instructions to add the camera.
4. Disconnect from the power adapter, then close the USB port cover.

• To avoid scratching the floodlight camera, do not peel off the protective film for the time being.
• The floodlights will only light up when in wired power mode. The USB- powered connection is used for setting up the camera safely inside your home.
• Make sure you can stream video from your floodlight camera BEFORE INSTALLATION.

The USB port cover must be closed to prevent water from entering the floodlight camera.

PREPARING FOR INSTALLATION (IMPORTANT)

Check local laws for installation
If you are outside of North America, installation and wiring must be performed by a licensed electrician. Always follow code standards when installing wired connections. Shut Power Off at the Breaker

Risk of Electrical Shock

• Turn off the power at your circuit breaker or fuse box before continuing, consult with a licensed electrician if needed.
• Switch on/off the lights to make sure the electricity to the installation area is shut off.
• Verify that the power supply is a 100~240 VAC 50/60 Hz power source.
• Keep the breaker off at any time during the installation process.

NOTE: Do not use a dimmer switch or timer for this product.

INSTALLING YOUR FLOODLIGHT CAMERA

Separate the Mounting Bracket
Separate the mounting bracket from the camera and set it aside for later installation.

Select a Location
You can mount the floodlight camera vertically on a wall or hang it from a ceiling. With the power off at the breaker, remove the existing floodlight if you have one.

For overhang mounting, reinstall the mounting base first.

Recommended Height
We recommend mounting the camera 8 ft (2.44 m) above the ground to achieve up to 40 ft (12 m) of motion detection range.

Install the Mounting Bracket

1. Install the mounting bracket on the wall or ceiling with the Wall
   Screws And Anchors (Bag A).

• For walls that are made out of hard materials, such as stucco, brick, or concrete, drill holes with a 15/64 inch (5.95 mm) drill bit, then insert the anchors into the holes.

Wall Mounting

Overhang Mounting

Connect Wires

1. Hang your camera on the bracket with the provided hook while connecting the wires.
2. Separately connect the ground wire (bare copper / green / green & yellow), live wire (brown), and neutral wire (blue) from the wall to the floodlight camera’s ground wire (green & yellow), live wire (black), and neutral wire (white) using wire connectors,  then secure the connections with a screwdriver.

Never cross-connect. The wires must be connected with matching colors.
If you have problems with the proper operation of the floodlight camera,
consult a licensed technician.

Place the Camera on the Mounting Bracket

1. Remove the hook, snap the mounting base onto the mounting bracket, align the holes, and secure it with 2 Base Screws (Bag B).
2. Remove the label and protective film from the floodlight.
   Clean the camera with a lens cleaning cloth.

ADJUSTING THE LIGHTING ANGLE

Manually pull up and down or left and right to adjust the floodlight vertically or horizontally.

RESTORING POWER

1. Switch on the main circuit breaker in the house. In case the floodlight camera is not powered on, switch off the circuit breaker before checking the wiring of the floodlight camera.
2. Now you can access various features and change settings in the eufy Security app. For troubleshooting, check the Help section in the eufy Security app.

LED LIGHT GUIDE

| Solid Violet| System is initializing
---|---|---
| Solid Blue| Working normally or ready for setup
| Blinking Red| Not connected to the internet
| Solid Red| Recording or the live stream is being viewed
| Flashing Blue and Red| Firmware upgrade in progress
Note: Keep the camera connected to a power source

SAFETY INSTRUCTIONS

• This equipment is not suitable for use in locations where children are  likely to be present. This equipment is not intended for use by children.
• Do not use the product in any way other than described herein in order to avoid personal injury or property damage.
• User should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Our company will not be responsible for any violators’ legal liability under any circumstances.
• An appropriate disconnect device shall be provided as part of the building installation
• An all-pole mains switch in accordance with Annex L shall be incorporated in the electrical installation of the building
• The luminaire internded to be mounted on or over an outlet box and shall be provided with supply conductors long enough to extend 150mm(6 in) into the outlet box.
• Caution, risk of electric shock

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED
MIN 90°C SUPPLY CONDUCTORS

NOTICE
**** This product complies with the radio interference requirements of the European Community.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/ EU.For the declaration of conformity, visit the Web site: https://uk.eufylife.com/
This product complies with the radio interference requirements of the United Kingdom
This product complies with the radio interference requirements of the United Kingdom.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with Radio Equipment Regulations 2017(SI 2017/1206). The full text of the UK declaration of conformity is available at the following internet address: https://uk.eufylife.com/
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.
The suitable temperature for the device and accessories is -20°C to 40°C.
It is recommended to supply the device in an environment with a temperature that ranges from 5°C~25°C.
When supplying, please place the device in an environment that has a normal room temperature and good ventilation.
RF exposure information
The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.
Frequency bands and power as below:

5150~5350 MHz can be used indoor only.
The following importer is the responsible party (contract for EU matters): Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich, Germany
The following importer is the responsible party (contract for UK matters): Anker Technology (UK) Limited | GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom
Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused.
**** This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on the disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Anker Innovations Limited is under license. Other trademarks and trade names are those of their respective owners.

CUSTOMER SERVICE

Kundenservice
12-month limited warranty

(US) +1 800-988-7973
(UK) +44 (0) 1604 936200

support@eufy.com

Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

@EufyOfficial
@EufyOfficial
@EufyOfficial

Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.

5100500XXXX V1
Raccolta Carta
PAP 22

References

• eufy - Built with Care | Home Security System & Robovacs | eufy UK
• eufy - Built with Care | Home Security System & Robovacs | eufy UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>