MB QUART NA2-400.2RC Nautic 400 Watt Amplifier Installation Guide

MB QUART NA2-400.2RC Nautic 400 Watt Amplifier

Product Information

The MBQuart amplifier is a high-quality audio amplifier designed to enhance your music experience. It offers various models, including NA2-400.2RC, NA2-320.4, NA2-400.1, and NA2-500.5. For more detailed information, system settings, speaker and subwoofer configuration, and full specifications for each model visit the website http://mbquart.com/manuals.html.

Before You Start

• Power Cable Size and Fusing:
  • Use the proper power and ground cable for your amplifier model.
  • Always use high-quality copper cables.
  • Refer to the website for multi-amp system cable recommendations.
  • Use the correct fuse size for each model. Some models require an external fuse.
  • For power cable runs over 20 feet, it is recommended to use an 8ga cable.
• Power and Ground Connection:
  • Place the terminal securely to avoid accidental contact with the negative battery post.
  • Properly route power, speaker, and RCA cables through the vehicle.
  • Choose a mounting location that provides adequate air ventilation.
  • Mount the amplifier to a secure surface and avoid mounting it upside down.
  • The chassis ground connection is critical. Choose a location close to the amplifier, scrape away paint, and use a nut and bolt if possible (do not use an existing factory bolt).
  • Ensure secure connections for the chassis ground, +12V, and remote wire.
  • Ground: Black,
  • Remote: Blue, +12V: Red
• Audio Connections:
  • Connect the RCA cables to the INPUT connectors. The OUTPUT can be used for a second amplifier input.
  • Turn the GAIN control completely counter-clockwise to a minimum.
  • Connect the speaker cables to the appropriate speaker output connectors based on the diagram for your speaker configuration.
• Setup
  • The amplifier has various controls for adjusting the audio output. Refer to the illustrations that match your amplifier model.
  • GAIN Control: This control matches the output of your source signal to the amplifier. Refer to the detailed instructions in section B below.
  • x-OVER Switch: This switch sets the amplifier to have a full frequency output or filters out high or low frequencies. The NA1-400.2RC offers either a bandpass or a high pass filter.

Before you start

CAUTION
Many new and factory radios require a reset code when disconnected from battery power. This is an anti-theft feature. Before unplugging power, you must determine if your radio/source unit requires a reset code. Check the operation manual for your vehicle or contact the dealer.

Power cable size and fusing

• It is critical to use the proper power and ground cable. Select the size listed here for your amplifier model.
• Always use high-quality copper cable. Visit our website for multi-amp system cable recommendations.
• Be sure to use the proper fuse size for each model. Some models require an external fuse.

Installation

1. Disconnect Negative Battery Terminal
   Place terminal in a secure position so that it won’t accidentally contact the negative battery post

2. Run Cables
   Properly route power, speaker and RCA cables through the vehicle.

3. Mount Amplifier
   Choose a mounting location that will provide adequate air ventilation. Mount the amplifier to a secure surface. Do not mount the amplifier upside down.

4. Chassis Ground
   The chassis ground connection is critical to the performance of the amplifier. Choose a location that is close to the amplifier. Completely scrape away the paint and use a nut and bolt if possible. DO NOT USE AN EXISTING FACTORY BOLT!

5. Power Connection
   Attach the chassis ground, +12V and remote wire. It is important to make sure these connections are very secure.

6. Signal Input Connection
   Connect the RCA cables to the INPUT connectors. The OUTPUT can be used to provide input for a second amplifier.

7. Gain Control
   Turn the GAIN control completely counter-clockwise to a minimum.

8. Speaker Connections
   Connect the speaker cables to the speaker output connectors. Follow the diagram below that best fits your speaker configuration.

9. Positive Battery Connection
   Connect the power cable to the positive battery terminal. The power cable must be fused within 18 inches of the battery terminal.

   • Be prepared to disarm your vehicle’s alarm and to enter your radio / source unit code.

10. Re-connect Negative
    Battery Terminal Re-connect the negative battery terminal making sure it is securely tightened.

Setup

Settings
The illustrations below describe the various controls. Refer to the illustration that matches your amplifier.

• GAIN Adjustment
  The gain control purpose is to match the output of your source signal to the amplifier. Refer to the section B below for detailed Instructions.

• x-OVER Switch
  This switch will set the amplifier to have a full frequency output or to filter out high or low frequencies. The NA1-400.2RC offers either a bandpass or a high pass filter.

• Frequencies Adjustment
  The Low Pass Filter will cut off the frequencies above the setting. The High Pass Filter will cut off the frequencies below the setting.

• SUBSONIC Adjustment
  The Subsonic Filter will cut off the frequencies below the setting. If using with a subwoofer the settin should be kept between 15-25Hz.

• Bsoosr Switch
  The Boost Switch will increase the signal 12dB at 45Hz. Be aware this setting can cause distortion if the gain is not set properly.

Level Setting
This is a critical step to insure your amplifier is properly adjusted to match the signal output level of your source unit.
THIS IS NOT A VOLUME CONTROL

1. If possible, with the source unit off, confirm that the primary volume control is turned down (counterclockwise).
2. Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is turned down. Make sure the source unit controls; balance, fader, bass, and treble are all set to center or “O” adjustment. Make sure that the green LED on the end of the amplifier is illuminated.
3. Play a clean musical selection of which you are very familiar. The CD is preferred. Do not use radio signals for level setting. Hit play and start turning the volume of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until you hear speakers begin to start producing distortion.
5. Increase the amplifier gain (clockwise) until the distortion is heard, then back the level down (counterclockwise) until the distortion is eliminated. Small adjustments may need to be made to balance the levels of multiple amplifiers.

Remote Level Control
Some models include a bass remote. Avoid adjusting the bass remote while operating the vehicle.

Assembly Instructions

Before you begin, read though these instructions and check that all parts are present. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation.

Parts List

No.| Component Name| Qty
1| Subwoofer| 1
2| MB Quart Grill Emblem| 1
3| Poly Fill Sheets| 2
Tools Required

1| T20 & T30 Torx Driver
2| 5mm Allen Wrench
3| Pry Tool
4| Utility Knife

Disassembly

• Remove rear floor panel
• Remove jack cover panel
• Remove three tie-down hooks with T30 Torx Driver and remove the side floor
• For Wrangler 4XE lift up the panel behind rear seat and remove
• Remove T20 Torx screw from the front side of the subwoofer panel
• Pop the rear seatbelt cover panel up and pry subwoofer enclosure off the rear quarter panel
• Disconnect the subwoofer enclosure wire harness
• Remove the T20 Torx screw from the rear of the subwoofer enclosure
• Remove the eight 5mm allen screws from the perimeter of the subwoofer
• Remove and disconnect the subwoofer.
• Gently pry up the OEM grill from the subwoofer frame
• Gently remove the original emblem from the front of the OEM grill
• Remove the OEM subwoofer wiring and grommet from the enclosure

Installation

• Install provided wiring harness and grommet into the enclosure
• Place the provided poly fill evenly into the enclosure while keeping the screw hole clear
• Cut and remove eight plastic tabs on the enclosure using a utility knife
• Connect the subwoofer to the wire harness
  • NOTE: Red to Positive and Black to Negative
• Install MB Quart subwoofer
• Install the OEM T20 Torx screw to the rear of the enclosure
• Install the new MB Quart emblem onto the grill, attach the grill and trim ring reusing the eight 5mm allen screws
• Place the subwoofer enclosure into the vehicle
• Route wiring towards your amplifier and connect it (in the case of the MBQJ-STG6-A-1 this will be under your passenger seat)
• Recommended amplifier crossover and gain settings with the MBQJ-STG6-A-1 kit are:
  • Gain turned up to the 1 O’clock position
  • LPF turned up to the 2 O’clock position
  • Subsonic turned up to the 9 O’clock position
• Reinstall the subwoofer enclosure into the quarter panel area and place the seat belt cover back in place
• Reinstall T20 Torx screw to the front of the enclosure
• For Wrangler 4XE install the panel behind rear seat
• Install floor side panel and three tie down hooks with T30 Torx screws
• Install jack cover
• Install rear floor cover and enjoy your MB Quart Subwoofer Upgrade

Congratulations on your choice of an MBQuart amplifier.  This “Quick Start Installation” guide is meant to help you”hook up” and play music. For more detailed information, on system settings, speaker and subwoofer configuration, and full specifications by model visit the website, http://mbquart.com/manuals.html.

• NA2-400.2RC
• NA2-320.4
• NA2-400.1
• NA2-500.5

References

• Maxxsonics | Powered by Maxxsonics. | Audio Stores Online

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>