kanto 310PS200 PS200 Full Motion TV Wall Mount User Manual

kanto 310PS200 PS200 Full Motion TV Wall Mount

Product Information

The product is the Kanto PS200, a wall mount for TVs. It is designed to support a maximum weight of 88 lb (40 kg). The mount is VESA compliant, meaning it is compatible with various VESA patterns including 100 x 100, 150 x 150, 100 x 150, 200 x 100, 100 x 200, 200 x 150, 150 x 100, 200 x 200, 200 x 250, 200 x 300, 200 x 400, 300 x 200, 300 x 300, 400 x 200, 400 x 300, and 400 x 400.

Product Usage Instructions

1. Before starting the installation, make sure that the supporting surface can handle the weight of your TV and the mount. Refer to the caution on page two for load limits.
2. Choose the appropriate template from the provided options to match your TV size and VESA pattern.
3. If you are mounting on a wood stud wall:
4. Mark the locations for the lag bolts (O) using the template.
5. Drill pilot holes with a 7/32 (5.5 mm) drill bit.
6. Attach the wall plate assembly to the wall using the lag bolts. Make sure each lag bolt is located in the middle of a wood stud and tighten them until the wall plate is snug against the wall. Do not over-tighten.
7. If you are mounting on a concrete or brick wall:
8. Make sure the wall is at least 4 inches thick.
9. Mark the locations for the concrete anchors (N) using the template.
10. Drill pilot holes with a 3/8 (10 mm) masonry drill bit.
11. Insert the concrete anchors into the pilot holes and make sure they are seated completely flush with the surface.
12. Attach the wall plate covers to conceal the mounting hardware.
13. If needed, use the provided plastic spacers to provide clearance around protrusions on the back of your TV or to accommodate a curved TV. Longer screws may be required when using spacers.
14. Make final adjustments to ensure the TV is level and securely mounted.
15. Ensure that the TV is not left resting on the screen. It should be supported by a wall mount or a TV stand.

FULL MOTION TV MOUNT

Thank you for choosing Kanto
Read these instructions fully before assembly and installation. If you do not understand these directions, or have any doubts about the safety of the installation, please consult a qualified installation contractor. Make sure there are no defective or missing parts. Do not use defective parts. Kanto cannot be liable for property damage or injury caused by incorrect mounting, incorrect assembly, lifting or incorrect use of this product. If there is hardware missing, or if you are uncertain whether a part is defective, please contact Kanto directly using one of the methods below.

See the installation video online at: www.kantomounts.com/resources
US & Canada: 1-888-848-2643
UK: +44 800086999
support@kantoliving.com

CAUTION
The maximum loading weight is 88 lb (40 kg). This mount is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in instability causing possible injury. The wall you plan to affix the Kanto mount to must be able to support more than 5 times the weight of the television and the mount combined. Do not use this product for any purpose other than to mount a VESA compliant TV on a vertical surface as outlined in this manual. Improper installation may cause damage to your TV or serious injury. This product should not be mounted on steel stud walls or cinder block walls. Consult a qualified installation contractor if you are unsure about the type of wall you may have.

Supplied Parts and Hardware

Required Tools

Wood stud wall

Concrete wall

Project Overview

1. Select TV Screws and Spacers
2. Select Spacers for Irregular TVs
3. Attach TV Brackets
4. Mount Wall Plate Assembly
5. Attach Wall Plate Covers
6. Hang and Secure TV
7. Level TV
8. Finalize Adjustments
9. Manage Cables

IMPORTANT!: Please read this entire document before attempting assembly
If you have any problems or difficulties while following these instructions, please contact Kanto directly:
Email: support@kantoliving.com
Toll Free: US & Canada: 1-888-848-2643 | UK: +44 800086999

Select TV Screws and Spacers

• A–I Select Screws
  The back of your TV has 4 screw holes in a square or rectangular pattern. This is where the mount will attach to your TV. Kanto provides several sizes and lengths of screws. This guide will help you select the right screws for your TV. You will only use 4 of the provided screws to attach your TV – the rest are not needed.

• J–K Select Spacers
  Plastic spacers are also provided in 2 thicknesses to allow the mount to work with curved TVs, and TVs that have recessed mount holes, protrusions, or inputs in the way. They can also be used to prevent the TV screws from going too deep and damaging your TV. You may not need spacers for your TV.

Select Spacers for Irregular TVs

Spacers can be used to provide clearance around protrusions on the back of your TV, or to accommodate a curved TV. You may need to use longer screws.

Attach TV Brackets

WARNING
Do not lay the TV face down on its front. Use a wall or TV stand

Only applicable if using M4 / M5 / M6 screw

Mount Wall Plate Assembly

Wood Stud Wall

Mount height depends on TV size, viewing position, and personal preference.

WARNING
Do not use concrete anchors in drywall or wood stud walls.

CAUTION
Make sure the supporting surface will support the load limits outlined in the caution on page two. Tighten lag bolts (O) until the wall plate is snug against the wall. Do not over tighten the lag bolts (O). Each lag bolt must be located in the middle of a wood stud.

Mount Wall Plate Assembly

Concrete Wall

• Mount height depends on TV size, viewing position, and personal preference.

• WARNING
  Do not use concrete anchors in drywall or wood stud walls.

• CAUTION
  Make sure the concrete or brick wall is at least 4” thick. Make sure the anchor is seated completely flush with the concrete surface even if there is another layer of material, such as drywall. If drywall is over 5/8” thick, custom lag bolts must be used. Concrete must be a minimum of 2000 psi in density.

Attach Wall Plate Covers

Hang and Secure TV

Level TV

Finalize Adjustments

Manage Cables

Limited Warranty to Original Purchaser

• Kanto Living Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material and workmanship for the limited warranty period of 5 years.
• If equipment fails because of such defects and Kanto is notified within 5 years from the date of shipment with proof of original invoice from an authorized reseller, Kanto will, at its option, provide replacement parts or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. Any replacement parts or replacement units are warranted for 90 days from the day of reshipment to the original purchaser.
• Customers will be responsible for obtaining a Return Authorization Number and paying shipping costs to return product to a Kanto location or authorized depot. If the equipment is covered under the warranty provisions above, Kanto will replace parts or provide a replacement unit, and be responsible for shipping costs to the customer. Please keep the original packaging to prevent damage to the product during shipping. Insuring your shipment is also recommended.
• The information in the manual has been carefully checked and is believed to be accurate. However, Kanto assumes no responsibility for any inaccuracies that may be contained in the manual. In no event will Kanto be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect, even if advised of the possibility of such damages. This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fitness for any particular purpose, all of which are expressly disclaimed.

www.kantomounts.com
support@kantoliving.com
Toll Free: US & Canada: 1-888-848-2643 | UK: +44 800086999

References

• TV Wall Mount Instructions and Resources | Kanto Mounts

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>