CRUX SWRFD-60T Wiring Interface Owner’s Manual
- July 17, 2024
- CRUX
Table of Contents
SWRFD-60T
Radio Replacement with Steering Wheel Control Retention for Select 2020 and Up Ford Vehicles
+
RADIO REPLACEMENT SWC RETENTION
PRODUCT FEATURES:
– Retains Factory Features in Select Ford Vehicles.
– Retains Factory Steering Wheel Controls via Built-in Pre-programmed
Interface.
– Made for Non Amplified Vehicles.
– Provides Accessory Power (2A max).
– Provides Illumination Output.
– Provides Reverse Signal.
PARTS INCLUDED:
SWRFD-60T MODULE SWRFD-60T HARNESS
SWC Cables Univeral Radio Key A Key B SWC
INSTALLATION DIAGRAM:
CRUX Module LED Feedback
| LED Light | POWER | Vehicle Programming Section |
|---|---|---|
| Solid Red & Blue | PASS | PASS |
| Slow Red Flash | FAIL | PASS |
| Slow Blue Flash | PASS | FAIL |
-
Illumination (+) Orange
-
Vehicle Speed Sense Pink or Red/Black
-
AMP TURN ON Blue/White
-
+12V Constant Yellow
-
+12V ACC Red
-
Ground Black
-
Reverse Gear Red/White or Violet/White
-
Right Front (+) Gray
-
Right Front (-) Gray/Black
-
Left Front (+) White
-
Left Front (-) White/Black
-
Right Rear (+) Violet
-
Right Rear (-) Violet/Black
-
Left Rear (+) Green
-
Left Rear (-) Green/Black
-
Yellow RCA
-
33 Pin Connectors
-
12-Pin Connector
-
To Retain Factory Back Up Camera
-
mini USB Not Used
-
3.5MM SWC CABLES (Option A or B)
Use the proper 3.5MM to 4-Pin cable for your radio. Plug in the selected 3.5MM SWC cable to the 4-pin port on the module. See “DIP SWITCH SETTINGS” section. -
Cap or insulate if not being used
-
BLUE / YELLOW FOR JVC & KENWOOD
-
Insulate with tape if not being used
DIP SWITCH SETTINGS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
RADIO BRAND: DIP#:| 1| 2| 3| SWC MODULE DIP SWITCH
---|---|---|---|---
Atoto, Dual, Fahrenheit, Jensen, Nakamichi,| OFF| ON| ON
Pioneer, Power Acoustik, Soundstream| OFF| ON| ON
Blaupunkt, Most off-brand Radio| OFF| ON| ON
Alpine| OFF| OFF| OFF
Clarion| ON| ON| OFF
Kenwood| ON| ON| ON
JVC| ON| OFF| ON
Boss, Old Sony | ON| OFF| OFF
New Sony (with CarPlay) | OFF| ON| OFF
NOTE: check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module or use the Blue/White
wire for JVC and Kenwood.
For aftermarket radios that have wires for SWC connections, cut off the 3.5mm plug on the Crux SWC Cable (option B) and connect the SWC wires as follows:
Note that there are some radios that only have SWC1 and SWC2, in this case “shield” does not need to be connected.
- RED to SWC Key 1
- WHITE to SWC Key 2
- SHIELD to SWC Ground
- Universal Radios
BROWN to SWC Key 1
BROWN/WHITE to SWC Key 2
VEHICLE APPLICATIONS:
FORD
2021 – Up E Series
2020 – Up Eco Sport
2020 – Up Escape
2020 – Up F250/F350/F450/F550
2020 – Up Transit
2020 – Up Transit Connect
NOTE:
Does not retain Sync.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone:818-609-9299 • fax:
818-996-8188 •
www.cruxinterfacing.com
rev.08312022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>