Dacom BoneBuds Bone Conduction Headphones User Manual

Dacom BoneBuds Bone Conduction Headphones User Manual

Touch Button Function

Accessories

• Charging Case *l

• Earphone *1 Pair

• Charging Cable *l

• Manual*1

• Ear Cap *2

Product Parameter

• Bluetooth Version: BT 5.3
• Speaker: Bone conduction speaker
• Frequency Response Range: 20Hz-20KHz
• Effective Distance: about 10m
• Rated Voltage: DC 5V
• Supported Agreement: HSP / HFP / A2DP / AVRCP

Warming Tips
As the picture 1 shows,take off the insulating film from the charging contact point for the first using,we suggest charging the earbuds at least 30mins before use them. As the picture 2 shows, Do not touch the charging point to avoid charging failed.

Operating instructions

Turn on/turn off

Turn on:

1. Take the headphone out of the charging case and the headphone will turn on automatically.
2. Press and hold the MFB button for 3 seconds to turn it on In the off state.

Turn off:

1. The headphone will turn off automatically and start charging when it being placed back in the charging case.
2. Press and hold the MFB button for 5 seconds to turn it off In the power-on state.

Bluetooth Pairing

1. Take 2 earbuds out of the charging case,the left and right earbuds will turn on and team up automatically,and the main ear will alternately flash red and green lights after the team is completed,and enter the pairing state
2. Turn on the bluetooth from the mobile phone,search for the pair name” bonebuds” on the phone and dick to pair it. When hearing the tone, the earbuds are connected with the mobile phone successfully.
3. If the earbuds were connected with mobile phone before,the earbuds will connect with mobile phone automatically while turn on earbuds.

Remarks:
If those 2 earbuds will not pair with each other,please take the two earbuds out of thecharging case,long press the MFB button until the the red and green indicator light flashes alternately, then double-click the MFB button either left-side or right-side earbud, then those 2 earbuds will be paired each other.

Clear Pairing Information

When the TWS is pairing, triple-press one of earbuds’ s MFB button ,then the paired information will be cleared ,the red indicator light flash once and the earbuds automatically turn off.

Forced Reset

When the earbuds cannot be turned on/off,press and hold the MFB button for 8 seconds in charging state,the earbuds will be reseted.

• Single Click: The MFB Button Answer /Reject Play/Pause

• Double-Click: The MFB Button Previous Song/Next Song

• Triple click: Volume- Volume+ Press and hold for two seconds
  Reject/ voice assistant(SIRI)

• Turn On/Off The Flash Light
  When the tws is under connection state,4-click MFB button of any earbuds to turn on/off the flash light.The left and right earbud are synchronously.
  NOTE: The flash light does not work when using only one of the eabuds.

• Low Battery Voltage
  Warning In all kinds of power on state, when the battery voltage is lower than 3.3v and the red light flashes once in 30 seconds ,that means the battery voltage is too low.

• Headphone charging
  Put the earphone into the base to charge, the red indicator light of the earphone will be on for 3s and then off, the green light of the base will flash 5 times, and then the power of the base will be displayed for 3s; when the earphone is fully charged and the green light will be on for 5 seconds, all the indicators will be off.

• Low battery indicator of charging compartment

• When the battery voltage of the charging base is less than 3.1V, the green light flashes quickly for 10 seconds, and the output is turned off. After low voltage protection, it needs to be activated by charging.

• Charging Case
  When the charging compartment is charging, the corresponding green light flashes, and the green light is off when fully charged.
  Note: Charging and power indication of the charging compartment: 25% for one grid, 50% for the second grid, 75% for the third grid, and 100% for the fourth grid.

SAFETY PRECAUTION

• Do not detach or modify the earphone for any reason otherwise it might get damaged or malfunctioned. Defectives under this category are not included for warranty.
• Do not expose the device into water or other liquid, otherwise it might get damaged or malfunctioned. Defectives caused by liquid inside are not included for warranty.
• Do not expose the earphone in extreme humidity or extreme temperatures (below 0 °C or above 45°C ).
• Avoid putting the indicator light near children eyes or animal eyes.
• Do not use the earphone in thunderstorm weather which might cause malfunction and increase the risk of electric shock.

WARRANTY SERVICE AND DESCRIPTION

Quality issues do not include user’s subjective judgment on sound quality. The warranty does not include plastic, manual and packaging. For those models that have been stopped for production, the company warrants for repairing the functions only.
Our company does not take any responsibility for the commitments dealers made to you but not within our company commitments.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>