SEALEY HVF18.V5 18 Inch Industrial High Velocity Floor Fan Instructions

June 4, 2024
SEALEY

18” INDUSTRIAL HIGH-VELOCITY FLOOR FAN
MODEL NO: HVF18.V5

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

1.1. ELECTRICAL SAFETY

WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before use. Inspect power supply leads, plugs, and all electrical connections for wear and damage. Sealey recommends that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey stockist.
If used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
For electrical safety information, it is important that the following information is read and understood.

√ Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
√ regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
√ Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse – see fuse rating in these instructions.
× DO NOT pull or carry the appliance by the power cable.
× DO NOT pull the plug from the socket by the cable.
× DO NOT use worn or damaged cables, plugs, or connectors. Ensure that any faulty item is repaired or replaced immediately by a qualified electrician.
√ This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove it from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommends that repairs are carried out by a qualified electrician.SEALEY HVF18.V5 18 Inch Industrial High Velocity Floor Fan -
Recommended fuse rating

1.2. GENERAL SAFETY

√ Disconnect the fan from the mains’ power when not in use and before servicing or performing any maintenance.
√ Use the fan in dry areas only. DO NOT use in wet or areas with high condensation.
WARNING! If a fan falls into water or other liquid, immediately switch off and disconnect from the mains power supply. DO NOT touch the fan until the mains power supply has been disconnected.
√ Always disconnect the fan from the power supply when moving it from one location to another and ensure the fan is standing on a level surface.
√ The fan airflow is powerful. Before use ensure that there is nothing nearby that will be damaged or displaced by the stream of air.
√ Keep the fan clean and maintained in good condition. For motor service contact an authorized service agent.
√ Use recommended parts only. Unapproved parts may be dangerous and will invalidate your warranty.
× DO NOT operate the fan where there are explosive or flammable gases, fumes, or other hazardous substances.
× DO NOT stand the fan on the power cable.
× DO NOT insert any objects through the fan guard.
× DO NOT cover the fan when in use.
× DO NOT immerse the fan in water or any other liquid.
× DO NOT allow children to operate the fan.
× DO NOT stand the fan where it may be knocked over or off a surface, or where the lead may cause a person to trip.
× DO NOT use the fan outdoors.
× DO NOT modify speed control or attempt to fit any additional external speed control device to the fan.
√ When not in use place the fan in its original box, or otherwise cover, to protect it from dust and store it in a safe, dry, childproof location.
NOTE: This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

INTRODUCTION

The high-velocity fan is suitable for the movement of huge volumes of air. Carefully balanced and fully guarded blades provide quiet and safe operation.
3-Speed power selection and cradle stand allow precise control of airflow to exactly where it is needed. Fitted with a 3-pin plug. Suitable for use in industrial, commercial, agricultural, automotive workshop, and showroom applications.

SPECIFICATION

Model No: SFF12
Fan Ø: ∅450mm(18″)
Speeds: 3
Speed Range: 1020/1130/1300rpm
Maximum Airflow: 107m³/min(3,760cfm)
Current 0.5A
Power: 110W
Supply: 230V
Maximum Fan Flow Rate (F): 82.76m³/min
Fan Power Input (P): 112.81W
Service Value (SV): 0.73 (m³/min)/W
Standby Power Consumption (PSB): 0.0W
Seasonal Electrical Consumption (0): 36.1kWh/a
Fan Sound Power Level (Lwa): 70.30dB(A)
Maximum Air Velocity (c): 4.27m/s

OPERATION

WARNING! Ensure that you read, understand, and apply safety instructions in Section 1 before using a fan.
4.1. Check that the speed control is set to “0” (off) and then plug into the mains power supply and switch the power on.
4.2. The fan features 3 speeds that are selectable using the switch located at the back of the fan above the motor. 1 or 2 settings will suit most needs, and 3 are used for maximum air movement.
4.3. Adjust the direction of the airflow by moving the base from side to side and tilting the fan up or down.
4.4. When you have finished using the fan, ensure you turn the speed control switch to “0” (off) and disconnect from the main power.

MAINTENANCE

WARNING! Ensure that the fan is disconnected from the mains power supply before attempting any of the following:
5.1. Use a soft, damp cloth to clean the fan. DO NOT immerse the fan in water and never allow water to drip onto the motor housing.
DO NOT use solvents, petroleum, paint thinner, or other chemicals to clean the fan.
5.2. To clean the fan blade, undo the five clips around the circumference, hinge up the front cover, and clean the blade with a slightly damp cloth. Replace the front grille and refit the five clips.
5.3. Should the motor, switch or power lead requires service or maintenance contact your local service agent.
5.4. When not in use place the fan in its original box or otherwise cover to protect from dust, and store in a safe, dry, childproof location.

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty:** Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SEALEY User Manuals

Related Manuals