CARBEST 67041 Portable Gas Water Heater Instruction Manual

Portable Gas Water Heater
50 mbar – 67041
30 mbar – 67042
USER’S INSTRUCTION

67041 Portable Gas Water Heater

WARNING!
FOR YOUR SAFETY USE OUTDOORS ONLY!
IMPORTANT:
This appliance is not intended for the supply of drinking water.
This appliance is intended for the supply of heated water for the purpose of washing &cleaning only.
Check and confirm safe water temperature before using this appliance.
Water from this appliance may be very hot.
Read these instructions carefully before use.
Familiarise yourself with the appliance before connecting it to the gas container.
Keep the instruction manual for future reference.

TECHNICAL INFORMATION:

Country of destination| BE,CH,CY,CZ,ES,FR,
GB,GR,IE,IT,LT,LU,LV,
PT,SI,SK,TR| AL,BA,BE,BG,CY,CZ,DK,EE,
FI,FR,GB,GR,HR,HU,IT,LT,LU,
LV,MD,MK,MT,NL,NO,RO RS,
RU,SE,SI,SK,TR,UA| PL| AT,CH,
CZ,DE,
SK
---|---|---|---|---
Appliance categories| | I 3+| 13B/P| 13B/P| I3B/P
Type of gas| G30| G31| G30| G30 G| 30
Supply pressure (mbar)| 28-30| 37| 30| 37| 50
Min gas pressure(mbar)| 20| 25| 25| 25| 42
Max gas pressure (mbar)| 35| 45| 35| 45| 57
Injector Size (mm)| 0.58| 0.58| 0.55| 0.49
Appliance type| Al
Applicable water pressure| 0.25-10 bar
Nominal heat input (Qn)| 5kW
Minimum heat input (Qm)| 2.8kW
Nominal heat output (Pn)| 4.2kW
Electrical rating| 12VDC
Water flow| 3 liters per minute (Tap average), 2-2.5 liters per minute (Shower head)
Size| 357x300x300mm
Weigt| 6,4 kg

STRUCTURE VIEW

1. Case
2. Mica Lamination
3. Aluminium foil
4. Valve bracket
5. Heat exchanger
6. Burner
7. Burner bracket
8. Burner bracket
9. Ignition pin
10. Sensor pin
11. Aluminium foil
12. Screw
13. Leg base
14. Foot
15. Base plate
16. Spacerdisc
17. Bottom plate
18. Sealing gasket
19. Controller
20. Inner Main plate
21. Pump socket
22. 12V DC input socke
23. ON/OFF switch
24. Water tap
25. Rear cover
26. Water connection
27. Tilt sensor
28. Gas connection
29. Flow sensor
30. Heat insulation
31. Sealing ring
32. Exhaust gas outlet
33. Exhaust shaf t seal 1
34. Exhaust gas shaf t
35. Thermostat
36. Exhaust shaf t seal 2
37. Gas pipe to burner
38. Gas valve assy
39. Gas pipe to valve
40. Handle base
41. Handle
42. Knob

GENERAL WARNINGS

• This appliance shall only be used with CE approved gas hose & regulator assembly and must be connected only to a propane gas cylinder that is appropriate certified.

• This appliance is to be stored in a dry & well ventilated location free from direct sunlight.
  Do not store when still connected to the cylin- der. Make sure that the cylinder is disconnect-ed and is stored in a well ventilated area, free from direct sunlight, heat and ignition sources.
  If being stored indoors insure that the location complies with the relative standard requirement.

• This appliance must only be serviced by an authorised agent, return to your place of purchase for service and repair.

• This heater is not to be used in wind speeds above 10 kph. The heater will extinguish at used in wind speed above 10 kph. This feature is governed by the safety feature fitted to the appliance.

• This appliance must not be used in enclosed areas, for example under awnings or tents.

• The appliance must be placed on a flat level surface (on & flat level standing on the ground or the table).

• This appliance must be installed in accordance with any national situation in force in the country of use.

• This appliance should be sited in an open area using, a natural surround features to protect it from direct wind.

• Forbid any interference with a sealed com-ponent

DANGER!

• This appliance is designed for outdoor use only.
• Do not use this appliance if it has leak, worn, deteriorated or damaged seals.
• Handle with care even after brief use, always pick up using the handle not the cylinder.
• It may be hazardous to attempt to fit other types of gas containers or cartridges.
• Use only in well ventilated area.
• This appliance shall only be used in an above ground open air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind & natural convection.
• Do not use adaptors or modify appliance to fit other connectors or cylinders.
• When using this appliance children must be supervised by an adult at all times.
• Never leave appliance unattended when operating.
• Do not use as a cooking appliance or modify for any other reason.

IMPORTANT

• OUTDOOR USE ONLY
  The appliance must be used outdoors only and is to be operated no closer than 800mm from the sides & 800mm from above to all combustible surfaces, fabrics, flammable materials & people.
  Must only be used on solid & stable horizontal surfaces made from non- combustible or non-flammable materials and should be protected from direct drafts and in a well ventilated place.

• CAUTION:
  Accessible parts may be very hot. Keep children away.

• Avoid twisting & kinking the Propane gas hose. If you smell gas immediately turn the gas off at the cylinder and move the appliance & cylinder to a well ventilated area outside, keeping well away from sources of heat such as naked flames & pilot lights.

CHECK FOR GAS LEAKS

• Check that all connections are tight that the gas cylinder connection has been tightened before you turn the cylinder gas valve on.
• NEVER check for leaks with a flame or pilot light.
• Using soapy water coated all connections, if bubbles appear turn the cylinder gas control off and retighten the connection before re-testing.
• Inspect the appliance regulator for signs of wear, leaks or incorrect operation.
• If symptoms leaks from seals or gas controls are identified do not attempt to repair, contact author- ized agent for help.
• To check if gas remains in the cylinder, disconnect from the appliance and hold the cylinder in a vertical position then shake from side to side, if there is a sound or feel of liquid movement inside the cylinder contains gas.
• When changing gas cylinders ensure this is conducted outside in a well ventilated location free from people, animals & ignition sources such as naked flames, pilot lights & electrical equipment with heaters or elements.

CARBON MONOXIDE HAZARD
This appliance produces carbon monoxide which has no odour. Using the appliance in enclosed spaces for example, caravan, car, boat or mobile home could cause DEATH.

COMPONENTS LIST

1. Water inlet
2. Gas inlet
3. ON/OFF switch
4. 12V DC input
5. Pump input
6. Gas control knob
7. View window
8. Handle
9. Shower head
10. 12V DC pump
11. 12V DC connector
12. Regulator and hose assembly not included in scope of delivery.

The legal regulations for this part vary from country to country. Please check with your retailer or Technician to fullfil the legal regulations before use.

APPLIANCE PERFORMANCE

• This appliance is designed to raise the outlet water temperature by and average of 25 °C above the source water temperature and can be adjusted by the gas control knob located on the top of the appliance.
• In the event that the temperature lift is insufficient simply run water through the appliance once returning the heated water to the source water reservoir then run again through the appliance until the desired temperature reached.
• Attach the DC pump & hose assembly to the appliance by quick connecting to the water inlet, then to the electrical connection marked “pump”.
• Attach the gas hose and regulator to the “gas inlet” then connect to the propane gas cylinder, tighten all connections with a spanner.

SAFETY FEATURE

This appliance is equipped with the following safety features:

• Over temperature sensor – the appliance will not allow the burner to remain in operation once the outlet water temperature reaches 50 °C, the burner will automatically relight once the outlet temperature falls below 50 °C.
• Water flow sensor – water must be flowing through the system to allow the burner to ignite. In the case that the water supply is restricted or ceases e.g. the water regulation switch is in the „OFF“ position, the burner will be extinguished and will not relight until the water flow recommences.
• Tilt switch – in the event that the appliance is moved during operation or is being operated on an unstable or non-solid surface the appliance will shut down and must be switched off until a suitable surface is located.

SETTING UP THE APPLIANCE

• Remove all components from the storage baand then place the appliance on a solid,stabsurface and straighten out all hoses to guartee no kinks or twists remain.
• Turn the gas cylinder on in an anti-clockwise direction full turn, then check connections for leaks with soapy water (DO NOT use a flame). If a leak is detected turn the cylinder valve off & retighten all connections then retest. If no leaks are detected turn the cylinder valve to the off position.
• Swing the water outlet pipe away from it is storage position to the side of the appliance. Take the shower head & hose assembly and attach to the water outlet.
• Check that the power switch at the rear of the appliance is in the “OFF” position. Connect the 12V DC lead in to the power socket marked “DC input” and then connect cigarette fitting in to a suitable DC power source.

OPERATING THE APPLIANCE

• IMPORTANT- During operation ensure that all air inlets & exhausts are kept free from obstruction and closure.

• WARNING- This heater is not to be used in wind speeds above 10kph. The heater will extinguish at used in wind speed above 10kph. This feature is governed by the safety feature fitted to the appliance.

• Submerge the pump in a suitable reservoir of clean water, DO NOT use water direct from rivers, lakes or the ocean. Locate the shower head in the desired position & ensure that the flow regulation switch is in the “open” position.

• Turn the gas cylinder valve on in an anti-clockwise direction one full turn then turn the power switch to the “ON” position. Water should start to flow from the shower head within 20seconds then the electronic ignition should be heard igniting the burner. The burner flame can be seen operating through the viewing window located on the front of the appliance. 

• Taking care to measure the temperature of the water flowing from the shower head, the temperature can be adjusted by turning the gas control knob from the minimum to maximum heat position fo reach the most desired heat level

• The water flow can be stopped at any time by sliding the regulation switch to the “OFF” position. The burner will then extinguish while the pump will still continue to operate.

• To reignite the burner slide the flow regulation switch to the “ON” position, water will commence to flow and the burner will ignite within 5 seconds.

• If the system is off because of overheat temperature on the water outlet, the system will be off automatically and not be restarted until operate manually. To restart the system, set the Power switch to the “OFF” position, and wait for the water outlet
  temperature lower to the limit of 50°C, then switch to “ON” again, burner will be reignited, and hot water will commence to flow.

• IMPORTANT: Water remaining in the heater exchanger while the flow is stopped may become hot. When the flow is resumed the user must check the temperature output to ensure that it is suitable for use and has not become too hot.

• Once the user has finished using the appliance switch the flow regulator to the “OFF” position and then turn the “Power” switch “OFF”.

STORING THE APPLIANCE

• With the appliance operating turn the cylinder gas valve in a clockwise direction to the “OFF” position. The burner will continue to operate until all gas has bled from the hose & regulator assembly. When this is completed switch the power off.
• Disconnect the DC input, pump & hose assembly from the appliance. Hold the pump approximately 1 meter above the ground and allow all water to drain out before rolling up and storing in the carry bag
• Disconnect the regulator & hose assembly from the appliance from the appliance & gas cylinder and store in carry bag.
• Disconnect the shower head & hose from the water outlet, hold the pump approximately 1 meter above the ground and allow all water to drain out before rolling up and storing in the carry bag. Return the water outlet to it’s storage position.

DISCONNECTING FROM CYLINDER

1. Check that the appliance is fully extin- guished, the gas cylinder control valve is in the fully “OFF” position & all surface are cool.
2. Loose the connection to the gas cylinder in a clockwise direction.

CARE INSTRUCTIONS

• Using warm soapy water with a mild detergent, wipe down all surface and areas of the appliance, taking care not to allow water to enter the burner outlets, mantle or aeration holes located in the base of the burner tube.

DO NOT: Submerge the appliance in a sink or bowl.
DO NOT: Use abrasive cleaners or bleach
DO NOT: Operate this appliance before reading the instruction booklet
DO NOT: Place articles on or against this appliance
DO NOT: Place chemicals or flammable materials, or spray aerosols near this appliance
DO NOT: Operate with panels, covers or guards removed from this appliance without ventilation
DO NOT: Operate in a boat, caravan or tent.

TROUBLE SHOOTING

This guide should be followed in case of failure of the appliance to operate correctly. If symptoms persist contact sales for help.

Water will not
flow from shower head| Check that appliance is switched on
Check sufficient water is available
Check that the pump is connected to the appliance
Check that adequate DC power is available
Check that the shower flow water regulator is in the open position
Burner will not light| Check that the water is flowing from shower head
Check that the water is not over temperature
Check that the gas cylinder is turned on and that there is gas in cylinder
Water is not hot enough| Check the gas control indicator
Let the water flow back into your water tank and then through the appliance again
Check that the gas cylinder is turned on and that there is gas in cylinder

WARRANTY
Reimo Reisemobil-Center GmbH, Boschring 10, 63329 Egelsbach (hereinaf ter referred to as „Reimo“ or „we“) grants you a warranty of 3 years in addition to the statutory warranty rights for products sold under Reimo‘s own brand „Carbest“.
The period for calculating the warranty period begins on the invoice date. The territorial scope of our guarantee extends to the territory of the Federal Republic of Germany.
Should material or manufacturing defects occur in the product you have purchased during the warranty period, we will provide you with one of the following services of our choice under this warranty:

• Free repair of the goods or
• Free exchange of the goods for an equivalent item

All original parts that have been replaced as part of the provision of warranty services become the property of Reimo.
The new parts or replacement parts become the property of the customer.
Repairs or replacements under warranty do not entitle the warranty period to be extended or restarted.
In the event of a warranty claim, please contact the dealer from whom you purchased the item in question or contact Reimo directly as the guarantor:
Reimo Reisemobil-Center GmbH, Boschring 10, 63329 Egelsbach, Phone: 06150 8662-310
The guarantee does not apply if defects other than material or manufacturing defects are found. Warranty claims are excluded in the event of damage to the goods caused by:

• Regular wear
• Improper and non-intended use of the product
• Improper operation, installation, assembly, commissioning or operation contrary to the respective instructions for use and/or installation, in particular if maintenance, care and warning instructions are disregarded
• Non-observance of any safety precautions
• Use of force (e.g. beatings)
• Own repairs
• Use of non-original parts from the manufacturer or parts not approved by the manufacturer
• Environmental influences (heat, humidity, etc.)
• Circumstances for which the manufacturer is not responsible (e.g. natural disasters, accidents)
• Improper transportation

The prerequisite for claiming under the guarantee is that you enable us to check the guarantee case (e.g. by sending in the goods). Care must be taken to ensure that damage to the goods during transportation is avoided by using secure packaging.
A copy of the invoice for the consignment of goods must be enclosed in order to claim under the guarantee. This is so that we can check that the guarantee conditions are met. Without a copy of the invoice, we may refuse to provide warranty service.
In the event of a justified claim under warranty, you will not incur any shipping costs, i.e. we will reimburse you for any shipping costs for sending in the goods.
Please note: This Reimo dealer guarantee does not restrict your statutory rights in the event of defects (warranty rights) against Reimo / a dealer and you can make a claim free of charge.
Any existing warranty rights against Reimo remain unaffected by this guarantee promise. This manufacturer‘s guarantee therefore extends your legal position.
In the event that the purchased item is defective, you may in any case assert your statutory warranty rights against Reimo, irrespective of whether a warranty claim exists or the warranty is invoked.

REIMO REISEMOBIL-CENTER GMBH
63329 EGELSBACH · BOSCHRING 10
GERMANY · WWW.REIMO.COM
MADE IN CHINA · © REIMO 01/2024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>