TWSG040-BK Metal Storage Shed

Product Information: This product is an outdoor frame
structure that needs to be secured to the ground to withstand
strong winds. The user manual provides step-by-step instructions
for assembling the product. The manual also includes a list of
parts and hardware required for assembly. Product Usage
Instructions: 1. Prepare the ground: – Level the ground before
installation. 2. Check parts and hardware: – Make sure you have all
the parts and hardware mentioned in “List 1” and “List 2” in the
manual. 3. Correct screw holes: – Use the hole position correction
drill to correct any unsymmetrical screw holes. 4. Assembly
instructions: – Use part A7 to connect part A1 (A4) and part A2
(A3) respectively. – Form the bottom frame with part A5 and fix it
with screws 1# and plastic gaskets. – Ensure that the four corners
are right angles. – Check if the two diagonal distances of the
square are equal using a tape measure. 5. Fixing corners: – Fix the
corners with part A and fasten them with screws 1# and plastic
gaskets. 6. Securing the frame to the ground: – Prepare bolts to
secure the frame to the ground. 7. Installing wall panels: –
Install part C/J2/C1 with screws 2#, gaskets, and nuts. – Place the
assembled wall (C/J2/C1) on the bottom frame (A1) and use screws 1#
and gaskets to fix it. – Place part J on the bottom frame (A5) and
use screws 1# and gaskets to fix it. – Repeat the above procedure
to assemble the other side. – Fix part C3 to part C1 (C2) with
screws 3#, gaskets, and nuts. 8. Installing side panels: – Place
part J/C/J1 on the bottom frame (A4/A5) and use screws 1# and
gaskets to fix it. 9. Fixing plastic caps: – Install part H5 with
screws 9# and gaskets. – Repeat the above procedure to assemble the
other side. – Use part H7 to connect part H3 and part H4 and fix
them with screws 3#, gaskets, and nuts. – Install the assembled
parts H3/H4 with screws 9# and gaskets. – Put on the plastic caps.
10. Installing part J1/J2: – Use screws 1# and gaskets to fix them
on the bottom frame. – Fix part H3/H4/H5 to part J1/J2 with screws
9# and gaskets. – Put on the plastic caps. 11. Installing part B: –
Connect part B1 and part B2. – Insert part B7 and B8 on the inside
of part B1/B2 with screws 12# and gaskets. – Insert part B7 on the
inside of part B3/B4 with screws 12# and gaskets. 12. Enclosing the
frame: – Enclose with part B1/B2, part B3/B4, and 2 part B5. –
Connect the four corners with part B and fix them with screws 12#
and gaskets. – Fix 2 part C4 on part B1, part B2 with screws 9# and
gaskets. 13. Installing the beam: – Place the assembled beam
(B1/B2, B3/B4, B5) on the upper end of the wall panel. – Fix it
with screws 1# and gaskets. 14. Fixing the upper end: – Fix the
upper end of part C1/C2 with part B1/B2 and part C4 using screws
3#, nuts, and gaskets. 15. Top frame assembly: – Splice part D1/D2,
clamp the two sides of part E and part D, and tighten with screws
3#, gaskets, and nuts. 16. Completing the assembly: – Put the top
frame on the beam (B1, B2, B3, B4) and fix it with 16 screws 1# and
gaskets. Please refer to the user manual for any additional
instructions or safety precautions.

Useboltstosecuretheframetothegroundtoagainstthestrongwind.

Themanualwillassistyouduringthewholeprocessofassembling. Makesureyouhavealltheparts&hardwareaslist1andlist2shown;
Preparethelevelgroundforinstallation.

1550-list 1

Hexagonalsocketwrench

Hole position correction drill

Cross screwdriver

1550-list 2

Hand Gloves

Hole position correction drill

Correctthescrew holesby hole position correction drill

Ifthescrew holesare notsymmetrical,
you can use this tool to correct the hole position.
Appendix

Plastic Gaskets
1.Firstly,usepart#A7toconnectpart#A1(A4)andpart#A2(A3)respectively andthenform thebottom framewithpart#A5andfixbyscrews1#andgaskets.
! Attention:fourcornersMUSTbeenrightanglesandcheckifthe twodiagonaldistanceofsquareisequalbytapemeasure

16
Plastic Gaskets
2.Fixthecornerswithpart#Aandfastenwithscrews1#andgaskets.

Plastic Gaskets

3.Youneedtoprepareboltsbyyourself to secure the frame to the ground.
A 4.Fix2part#C3onpart#A1,part#A2byusingscrews9#and A gasketsasshownin. A
A

SteelGaskets

Plastic Gaskets 2SteelGaskets

Step1:Installpart#C/J2/C1withscrews2#,gasketsandnutsasshownin. Step2:Placetheassembledwall(C/J2/C1)onthebottom frame(A1),using3 screws 1# and gaskets to fix.

Step3:Placepart#Jonthebottom frame(A5),using3screws1#andgasketstofix. Repeattheaboveprocedurestoassembletheanotherside. Step4:Fixthepart#C3tothe part#C1(C2)with2screws3#, gaskets and nuts each as shown in.
03

Step1:Placepart#J/C/J1onthebottom frame (A4/A5),using7screws1#andgasketstofix.

Plastic Gaskets
8
Plastic Gaskets

Front side

Back side
Step2:Installed2part#H5with4screws9#and gasketsthenputontheplasticcapsasshown in . Repeattheaboveprocedurestoassemblethe anothersideasshownin . 04

2SteelGaskets

8
Plastic Gaskets

Usepart#H7toconnectpart#H3andpart#H4,andfixbyscrews3#, gaskets and nuts.
Front side

1 2
1 2

3 2
3 2

Back side
Installed2assembledpart#H3/H4with8screws9#andgaskets,thenputontheplastic capsasshownin .
Plastic Cap

1

Before

2

After

3

Plastic Gaskets Plastic Gaskets

Installpart#J1/J2:Usescrews1#andgasketstofixthem onthebottom frame. Fixpart#H3/H4/H5topart#J1/J2withscrews9#andgaskets,thenputontheplasticcaps.

Before

After

Front side Back side

Plastic Gaskets

Firstly,connectpart#B1and part #B2; Secondly,insertpart#B7&B8 on the inside of part #B1/B2 with screws 12# and gaskets asshownin.
Insert part #B7 on the inside ofpart#B3/B4withscrews 12# and gaskets as shown in .
07

16 Plastic Gaskets

Plastic Gaskets

Enclosewithpart#B1/B2,part#B3/B4,2part#B5accordingto thefigureabove,andthepart#Bconnectsthefourcorners, thenfixedwithscrews12#andgasketsasshownin.

Fix2part#C4onpart#B1,part#B2byscrews9#and gasketsasshownin .
!
08

Plastic Gaskets
SteelGaskets
Placetheassembledbeam (B1/B2,B3/B4,B5) ontheupperendofthewallpanel,andfixwith thescrews1#andgasketsasshownin.

Fixtheupperendofthepart#C1/C2withpart#B1/B2andpart#C4byusingscrews3#, thenutsandgasketsareonthebacksideasshownin.

09

Inside View

Inside View

Top frame assembly

2SteelGaskets

Splicethepart#D1/D2,clampthetwosidesof thepart#Eandpart#D,andtightenwiththe screws3#,gasketsandnuts.

10

Plastic Gaskets
Putthetopframeonbeam (B1&B2&B3&B4),using16screws1#andgaskets.
11

SteelGaskets
ASSEMBLE THE TOP ROOF
Assemblethepart#G1/G2totheonesideofpart#K1/K3withscrews2#, gaskets and nuts.
12

SteelGaskets Plastic Gaskets

Plastic Caps

Theroofpanelpart#K1/K2/K3islaidinorder;Part#Zshallbeinsertedatthefixedpositionoftopbeam andtoprooftopreventrainwaterintrusionasshownin;theroofpanelK1/K3isfixedwith G1/G2& D1/D2byusingscrews2#,gasketsandnutsasshownin,thenfixwithscrew 1#and gasketstosideframebeam.
13

SteelGaskets

2SteelGaskets

1.Installthepart#F:Securebothends ofpart#Ftothepart#K1/K3andpart

D1/D2,asshownin.

2.Plugpart#G asshownin.
14

2SteelGaskets

Installthepart#G5/G6withscrews3#, gaskets and nuts.

Usescrews7#toinstallthepart#F1from theinside.

15

SteelGaskets

The front side of the left door

The back side of the left door

16

SteelGaskets

The back side of the right door

The front side of the right door

17

SteelGaskets
InstalltheDOOR

There is a bolt on the left door

There is a handle on the right door

Fixthehinge(part#Y)totheleft/rightdoorbyscrews8#,gasketsandnutsasshownin.

18

Insert the bolt and lock the door
Insert the bolt and lock the door 19

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>