WELLFOR EBM364818 LED Lighted Mirror Fixture Instructions

October 30, 2023
WELLFOR

WELLFOR EBM364818 LED Lighted Mirror Fixture

WARNING AND SAFETY INSTRUCTIONS

Before assembling your LED Lighted Mirror fixture, please make sure that you carefully read through this instruction sheet, and refer back to them during installation to ensure your product is fitted safely and correctly. Keep these instructions for future use.

WARNING Risk of Fire and Electric Shock

All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician. Switch off the electrical supply at the main circuit board BEFORE installation and maintenance. Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror. Regularly check the cord, the transformer, and all other parts for damage, if any part is damaged the product should not be used.

INSTALLATION SAFETY

Inspect the product immediately upon receipt for transit damage or missing parts. Handle the product with care and protect against knocks to all sides and edges of the glass. Ensure there are no hidden pipes or cables in the wall before drilling. Wear suitable eye protection when drilling. Take care of drilling on tiled surfaces in case the drill slips.

CAUTION

PRODUCT DESCRIPTION & INFORMATION

The LED mirror comes with a flexible ruler leveling instrument and two hanging bars for horizontal and vertical hanging options. The mirror has a built-in touch switch that controls the LED light and anti-fog pad. The LED light is dimmable.

TOOLS YOU MAY NEED

  • Electric drill
  • Screws and expansion plug
  • Eye protection

3. INSTALLATION PROCESS

  • Step 1: Measure the distance between the holes on the hanging bar and use an electric drill to punch holes on the wall.
  • Step 2: Fix the hanging bar to the wall with screws. Drive the expansion plug into the hole on the wall, then put the screw into the expansion plug.

OPERATION PROCESS

  • Step 3: If wiring installation is required, ensure that the mirror is turned off when the power supply in the house is cut off. Then connect the power cord of the mirror and the on the wall with the terminal block. White wire = Neutral wire, black wire = Live wire, Light green wire = Earth wire.
  • Step 4: Hang the mirror with desired placement by using the two hanging bars provided.

LED Mirror Power Source FAQ
Scenario 1 (Direct Wired): This is the most common way to connect the mirror. The LED light and anti-fog pad are both controlled by the built-in touch switch on the mirror. The LED light is dimmable.

WARNING AND SAFETY INSTRUCTIONS

Before assembling your LED Lighted Mirror fixture, please make sure that you carefully read through this instruction sheet, and revert back to the dung installation to ensure your product is fitted safely and correctly. Keep these instructions for future use.
WARNING Risk of Fire and Electric Shock

  • All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician.
  • Switch off the electrical supply at the main circuit board BEFORE installation and
  • Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
  • Regularly check the cord, the transformer, and all other parts for damage, if any part is damaged the product should not be used.

INSTALLATION SAFETY

  • inspect the product immediately upon receipt for transit damage or missing parts. Handle the product with care and protect against knocks to all sides and edges of the glass.
  • Ensure there are no hidden pipes or cables in the wall before drilling.
  • Wear suitable eye protection when drilling. Take care of drilling on tiled surfaces in case the drill slips.

CAUTION: The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Do not install this fixture in hazardous locations.

PRODUCT DESCRIPTION & INFORMATION

WELL-FOR-EBM364818-LED-Lighted-Mirror-fig-1

INSTALLATION PROCESS

  • Step 1
    Measure the distance between the holes on the hanging bar, use an electric drill and punch holes on the wall

  • Step 2
    Fix the hanging bar to the wall with screws䯖䯒Drive the expansion plug into the hole on wall. then put screw into the expansion plug䯓

  • Step 3
    If wiring installation is required, ensure that the mirror is turned off when the power supply in the house is cut off. Then connect the power cord of the mirror and the on the wall with the terminal block . White wire = Neutral wire, black wire = Live wire, Light green wire = Earth wire.WELL-FOR-
EBM364818-LED-Lighted-Mirror-fig-3

  • Step 4
    Hang the mirror with desired placement by mirror

OPERATION PROCESS

  1. Light on/off
    Press to turn on the light, long press to steplessly adjust the color temperature,
    short press to turn off the light.
    Press to turn on the light, long press to steplessly adjust the brightness,
    short press to turn off the light

  2. Anti-fog function
    Short press to turn on/off defogging

Power-off memory:
When the light is turned on, the power is turned off directly, and the light will automatically light up when the power is turned on next time. If the power is turmed off when the light is off, you need to touch the switch button to turn on the light when you turn on the power next time.

LED Mirror Power Source FAQ

  • Scenario 1
    (Direct Wired) This is the most common way to connect the mirror. The LED light & anti fog pad are both controlled by the built-in touch switch on the mirror. *The LED light is dimmable.

  • Scenario 2
    (Wall Switch) By doing so, the mirror is now bridged to the wall switch. In order to turn on the mirror, the wall switch needs to be on. The touch switch can be used to turn on the LED mirror and anti-fog pad. The mirror shuts down once the wall switch is filpped to OFF.

  • Scenario 3
    (Wall Dimmer Switch – Not Accepted) This is a scenario that is not acceptable. There is no work around for our mirror. Do not try this way as it will damage the LED driver.

Internal Power Flow DiagramWELL-FOR-EBM364818-LED-Lighted-Mirror-
fig-9

Documents / Resources

| WELLFOR EBM364818 LED Lighted Mirror Fixture [pdf] Instructions
EBM364818, EBM364818 LED Lighted Mirror Fixture, LED Lighted Mirror Fixture, Mirror Fixture, Fixture
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

WELLFOR User Manuals

Related Manuals