ROUGH COUNTRY 921510700 Bronco Bumper Cube Mount Instruction Manual
- June 13, 2024
- Rough Country
Table of Contents
ROUGH COUNTRY 921510700 Bronco Bumper Cube Mount
Product Information
Product Name: 21 and Up Bronco Bumper Cube Mount
Product Code: 921510700
Manufacturer: Rough Country
Notice to Dealer and Vehicle Owner
Any vehicle equipped with any Rough Country product must have the Warning to Driver decal installed on the sun visor or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling characteristics. It is the responsibility of the installing dealer to install the warning decal and forward these installation instructions to the vehicle owner for review and to be kept in the vehicle for its service life.
Kit Contents
- Driver Mount
- Pass Mount
Product Usage Instructions
- Park your vehicle on a clean flat surface, engage the parking brake, and block the rear tires.
- Save all hardware removed from the vehicle unless otherwise noted.
- Open the hood and disconnect the negative terminal on the battery.
- Install your lights to the Rough Country brackets at an angle as shown. All the mounts are adjustable for preference once in the vehicle. Passenger side shown. (Refer to Photo 1)
- Use zip ties if desired to attach the light harnesses to the mounts as shown. (Refer to Photo 2)
- Remove the 3 Torx head bolts from both sides of the wings on the bumper using a T35. (Refer to Photo 3)
- Slide the assembled brackets into place from behind the bumper and install using the factory hardware. Adjust the lights to suit your preference. Tighten all the hardware. (Refer to Photo 4)
Rough Country recommends that a certified technician install this system. In addition to these instructions, professional knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle. Please read all the instructions before beginning the installation. Check the kit hardware against the ‘’Kit Contents’’ list below. If question exist, please call us @1-800-222-7023. We will be happy to answer any questions concerning this product. Check all fasteners for proper torque. Check to ensure for adequate clearance between all components. Check and retighten wheels at 50 miles and again at 500 miles. Periodically check all hardware for tightness. Be sure you have all the needed parts and understand where they go. Also, please review the “Tools Needed” list to be certain you have the necessary tools to complete the installation.
PRODUCT USE INFORMATION
WARNING As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend that seat belts and shoulder harnesses be worn at all times. Braking performance and capabilities are decreased when significantly larger/heavier tires and wheels are used. Do not add, alter, or fabricate any factory or after-market parts which increase vehicle height over the intended height of the Rough Country product purchased. Rough Country makes no claims regarding lifting devices and excludes any and all implied claims. We will not be responsible for any product that is altered.
NOTICE TO DEALER AND VEHICLE OWNER
NOTICE Any vehicle equipped with any Rough country product must have the “Warning to Driver” decal installed on the sun visor or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique han-dling characteristics. INSTALLING DEALER—It is your responsibility to install the warning decal and to forward these installation instructions on too the vehicle owner for review and to be kept in the vehicle for its service life
Cube Mount Installation
- Park your vehicle on a clean flat surface, engage the parking brake and block the rear tires.
- Save all hardware removed from the vehicle unless otherwise noted.
- Open the hood and disconnect the negative terminal on the battery.
- Install your lights to the Rough Country brackets at an angle as shown. All the mounts are adjustable for preference once in the vehicle. Passenger side shown. Photo 1
- Use zip ties if desired to attach the light harnesses to the mounts as shown. Photo 2
- Remove the 3 Torx head bolts from both sides of the wings on the bumper using a T35. Photo 3
- Slide the assembled brackets into place from behind the bumper and install using the factory hardware. Adjust the lights to suit your preference. Tighten all the hardware. Photo 4
Run the wiring to suit. If your vehicle is equipped with the factory auxiliary switch panel, you can wire the lights to this using the pigtail under the hood on the driver side firewall. It is suggested that you retain the relay set up that comes with the light kit. Cut the switch off the harness and use the trigger wire and attach to the factory harness. You can also pur-chase the MLC6 option offering for the Bronco from Rough Country made specifically to tie to the factory auxiliary panel and wire harness. This will keep all your harnesses neat and tidy and offer superior protection against battery drain due to the auto drain feature. DO NOT tie all 6 lights to one harness. You can tie the harnesses to one switch, but make sure to use all the relays from each kit.
By purchasing any item sold by Rough
Country, LLC, the buyer expressly warrants that he/she is in compliance with
all applicable , State, and Local laws and regulations regarding the purchase,
ownership, and use of the item. It shall be the buyers responsibility to
comply with all Federal, State and Local laws governing the sales of any items
listed, illustrat-ed or sold. The buyer expressly agrees to indemnify and hold
harmless Rough Country, LLC for all claims resulting di-rectly or indirectly
from the purchase, ownership, or use of the items.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>