Aodehong H21 3 In 1 Magnetic Wireless Charger User Manual
- June 13, 2024
- Aodehong
Table of Contents
Aodehong H21 3 In 1 Magnetic Wireless Charger
Product Introduction
The product is a 3-in-1 wireless charging pad, a preferred smart chip, and supports mobile phones, smartwatches, and earphones. Achieve high efficiency, and stable performance, Put it on and charge, and easily enjoy wireless charging technology life. It can also wirelessly mobile phones or other electronic devices that support Si standard
Specification
- Model: H21
- Input: QC/PD 18W Type-C
- Output: 7.5W (Smart Phone)
- Output: 3W (Earphone)
- Output: 2.5W (Smart Watch)
- Conversion science. 80%6-85%
- MateriAls’ ARSEPC-MetA
- Size: 1018 76*32mm
- Weight: 188g
Compatibility
Smart Phone
- For Apple: iPhone 14 / iPhone 14 Pro / iPhone 14 Pro Max / iPhone 14 Plus /
- iPhone 13 / iPhone 13 Pro / iPhone 13 Pro Max / iPhone 13 mini / iPhone 12 /
- iPhone 1 pro i hone Fro max iPhone 12 mini (Case compatibility: Non-metallic Case thinner than 4mm your device
Watch
Apple Watch Series 2 / 3 / 4 / 5 / 6 / 7 / 8 / SE / Ultra
Earbuds
AirPods 2 (with wireless case) / AirPods Pro / AirPods Pro2 / AirPods 3
Charging Method
-
Layflat Mode: Lay the device flat on the charging pad(the device must be centered on the charging pad)
-
Hover Mode: In this mode, you can adjust the angle of the iPhone at will, and even rotate it a will.
Not only can it be charged, but it can also be used as a cell phone holder. -
Folding Mode: Minimal size to maximize desktop space savings.
-
3D Mode: Small size while still being able to charge multiple devices.
FCC Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE : This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by
turning the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is a device.
- Consult the dealer or an experienced radio/ TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface ot the device must be respected
IC Warning Statement
This device contains license-exempt transmitter-receivers that comply with
Innovation Science and Economic Development Canada’s license-exempt Ross.
Operation is subject to the following two conditions:
(1) This device may not cause interference and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment; During the operation of the device a distance of 10 cm surrounding the device and 10 cm above The top surface of the device must be respected.
Safety Notice
- Please do not pull the power cord strongly to avoid the power cord breaking or falling off.
- Do not disassemble or put into fire or water to avoid short circuit and leakage
- Do not use the product in severe heat, humidity, or corrosive environments to avoid damage to the circuit leakage
- Please do not give children to play to avoid unnecessary accidents.
- When using fast charging, please use a qualified QC3.0 charging power adapter and fast charging cable, otherwise, it may cause charging instability.
- Please do not put metal debris or magnetic cards on the charging board, which may cause damage or abnormalities to the charger.
- If you encounter the receiving coil or transmitting board overheating during use, resulting in stopping charging, please remove the charging product, wait for it to cool down, and then try charging again.
Package List
- 3 in 1 wireless charger * 1
- Type-C charging cable * 1
- 18W adapter * 1
- User manual * 1
- Storage Box *
FAQ and Solution
Is the phone not charging?
The phone is not aligned with the sensing area or the receiving coil is not
installed.
Heats up while charging?
It is normal for the receiving coil or the transmitting board to heat up
during the wireless charging process.
Phone charging intermittently?
If the charging current of the adapter is not enough or the voltage is
unstable, please use the QC3.0 fast charging adapter to charge. The charging
position is too biased, and the electromagnetic induction is not good. The
charging position can be adjusted.
The main unit indicator light is normal, but the mobile phone does not
work?
The receiving coil of the mobile phone is faulty, it is recommended to update
the receiving coil or repair the mobile phone (built-in receiving coil).