Tribit BTH96 FlyBuds C2 True Wireless Earbuds User Manual

Tribit BTH96 FlyBuds C2 True Wireless Earbuds User Manual

package contents

How to wear the Earbuds

Power ON / Power OFF

Bluetooth Connectio Instructions

Connect the earbuds to a Bluetooth device:

Open the charging case and the earbuds wit/ automatically enter the Bluetooth pairing mode. then the earbuds* indicator lights will flash alternately red and white. Turn on the Bluetooth function in the Bluetooth device, refresh the Bluetooth device listing, then select the paired audio device named “Tribit Flyeuds C2” to connect The indicator lights of the earbuds will go off after it connects successfully.

Connect the earbuds with other devices:

Method 1: Please disconnect the earbuds with the currently connect-ed Bluetooth device, and the earbuds wilt automatically enter Bluetooth pairing mode.
Method 2 : Tap either earbud for 4 times. When the white indicator light goes on, touch and hold the earbud for 3 seconds. When the indicator lights of both earbuds flash in red at the same time, the earbuds will automatically enter Bluetooth pairing mode.

Touch Control Instructions

Charging Instructions

When the earbuds’ indicator lights flashes in red slowly, please charge

the earbuds in time

• .To charge the earbuds: Put the earbuds into the charging case and close the case to star cnarging, The indicator lights on the far left and right of the charging box show the charging status of the each earbud. During charging, the indicator tights will be always on and will go off after the earbuds are fully charged.
• Charging time of the earbuds: about 90 minutes Open the top cover of the charging case and it’ll display its battery level. When the battery runs out, the indicator light of the charging case will be off. Please charge the case in time. •To charge the charging case: Plug one end of the USG cable into a 5V power supply, and the other end into the charging port of the charging case for charging. The indicator tights wilt flash during the charging process, and the 4 indicator tights will stay on when the earbuds are fully charged.
• Charging time of the charging case: about 90 minutes *The above data comes from Thousandshores Laboratory. S Thousandshores reserves all rights for final explanation,

How to reset the Earbuds

Step 1: Turn off the left and right earbuds. Touch and hold the touch area for 10 seconds (at the 6th second, the earbuds will turn on with the white indicator light flashing once and then go out).
Step 2: Double touch the left and right earbuds to enter the reset state within 5 seconds.
Step 3: After the earbuds are reset successfully, the white lights of the left and right earbuds will flash Quickly.
Note: After resetting, if there is a Bluetooth device that has been connected to the earbuds, you need to delete the pairing record to allow the earbuds to be paired again.

Frequency band & Maximum transmission power

Frequency band: 2402-24801v1Hz lvlaximurn transmission power: -6 – +4dem

Warning

1. Do not dismantle or modify the earbuds for any reason, otherwise any malfunction of the earbuds is not covered by the warranty.
2. Do not deliberately contact the earbuds to liquids, which may damage the earbuds may be damaged and the warranty turns invalid,
3. Do not place the earbuds in the environment where the temperature is too high or too low (above 45 or below -20 C ).
4. This product includes a bulit-in lithium battery. it is forbidden to disassemble. bump, squeeze or throw the product into fire.
5. Please keep the earbuds away from children to avoid accidental swallowing and other injuries,

Important Notes

1. Under noisy environment, the voice from the earbuds wilt sound tower than the actual volume.
2. Listening to music with high volume for a long time may cause permanent damage to your hearing. 3, Please use the charging cable and power adapter or computer to charge the earbuds. When charging, only use the adapter that comply with the national/regional regulations and International and regional safety standards.

FCC Statement

Changes or modifications not expressly approved by the party responsi -ble for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful Interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the Interference by one or more of the following measures:
— Reorient or relocate the receiving antenna. — increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is sublect to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received. including interfer-ence that may cause undesired operation.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>