RYNOSKIN RS-JSS-021 2007-2018 Jeep Wrangler JK 2 Door Heavy D Instruction Manual

RYNOSKIN RS-JSS-021 2007-2018 Jeep Wrangler JK 2 Door Heavy D

Product Information

• Product Name: Rocker Step
• Part Number: RS-JSS-021
• Compatible Vehicle: 2007-2018 Jeep Wrangler JK 2 Door
• Installation Time: 60-120 minutes
• Cutting Requirement: Not Required
• Drilling Requirement: Not Required

Torque & Tools

BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.

Part List

INSTALLATION INSTRUCTION

1. Start installation toward the front of the Driver/Left side of the vehicle, Locate the front and rear mounting locations (Fig 1).
2. Determine if the vehicle has an open floor panel or a threaded hole in the floor panel.
3. Vehicles with open mounting location:

  *  **a.** Insert (1) 10mm Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the hole in between the pair of holes on the pinch weld, (Fig 2).
  *  **b.** Select the Driver/Left Front Mounting Bracket.  

NOTE: There is a small notch at the Rear of the Rear Brackets. Please identify the Front Bracket and Rear Bracket according to the Part List.

  *  **c.** Attach the Bracket to the Nut Plate with (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm x 34mm Flat Washer, (Fig 3). Do not tighten hardware.
2.  **Vehicles with factory threaded hole in floor panel:**
  *  **a.** Select the Driver/Left Front Mounting Bracket. Attach the Bracket to the front mounting location (Fig 4) with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Fig 5). Do not tighten hardware.![RYNOSKIN-RS-JSS-021-2007-2018-Jeep-Wrangler-JK-2-Door-Heavy-D- \(6\)](https://manuals.plus/wp-content/uploads/2023/10/RYNOSKIN-RS-JSS-021-2007-2018-Jeep-Wrangler-JK-2-Door-Heavy-D-6.png)

3. Select (1) Driver/Left Support Bracket (#1). Attach the Support Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Fig 6).

4. Attach the Support Bracket to the Mounting Bracket with (1) 10mm x 30mm Hex Bolt, (2) 10mm x 20mm Flat Washers and (1) 10mm Nylon Lock Nut, (Fig 7). Do not tighten hardware.

5. Repeat Steps 2 – 4 to attach the Driver/Left Rear Mounting Bracket and Support Bracket to the rear location, (Figs 8-9). NOTE: There is a small notch at the Rear of the Rear Brackets. Please identify the Brackets according to this, (Fig 10). Do not tighten hardware.

6. Select the Driver/Left Rocker Step.
   NOTE: The Driver/Left Rocker Step will have a “21-L” on the front. Attach the Rocker Step to the Mounting Brackets with (4) 8mm Combo Bolts, (Fig 11). IMPORTANT: Do not slide Rocker Step on the Mounting Bracket cradles, or damage to the finish may result. Do not tighten hardware.

7. Level and adjust the Rocker Step and tighten all hardware.

8. Repeat Steps 2—7 to attach Passenger/Right Rocker Step.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Rocker step.

www.rynoskinauto.com
Customer Support: service@rynoskinauto.com

References

• RYNOSKIN

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>