4homes BW2039 Bubbler with Cold White LED Glass Ball and Ornamental Plant Instruction Manual
- June 13, 2024
- 4homes
Table of Contents
4homes BW2039 Bubbler with Cold White LED Glass Ball and Ornamental Plant
SPECIFICATION
- Energy source: 220 – 240 V AC, 50/60 Hz
- Light source: Cool white
- Performance: 3 W
- Max current: 0.05 A
- Pump water flow: 0.5 – 1 L / hour
- Cable length: 145 cm
- Cable type: HO3VVH2-F 2 x 0.75 mm?
- Wire color: Black
- Water temperature: 10-35 °C
- Amount of water required for operation: 0,7 – 1.9 L
- Glass ball diameter: Ø50 mm
- Full size: 280 x 170 × 250 mm
- Weight:
- Empty: 2300 g
- Filled with water: 4200 a
User manual
Thank you for choosing our product, we hope you will use it for a long time
with satisfaction! Please read the following operating instructions carefully
for safe operation and keep them for future reference.
Warnings
General advice:
Danger of suffocation! Please keep the packaging of the appliance out of the
reach of children as it may lead to suffocation. The appliance may only be
used by adults, the storage location must be chosen in such a way that
children cannot accidentally access it. Children should be supervised to
ensure that they do not play with the appliance. The device may only be used
for its intended purpose! When using, pay attention to the physical safety and
safety of those around you (especially children). The device may only be used
by people who have read, and understood this operating manual and are able to
operate the appliance! People with reduced mental, physical or sensory
capabilities must not use the device! Children should not use the appliance!
Do not use the appliance if you have previously dropped or smashed it and it
is visibly damaged! The light source that provides the fountain’s mood light
cannot be replaced!
Danger of slipping:
The area around the product may be wet due to the operation of the fountain!
Use caution.
Risk of electric shock:
Never operate the appliance with wet hands! It is strictly forbidden to touch
the device, especially the mains plug and the cable with wet hands! The device
may only be connected to AC power with the correct voltage. Only connect the
appliance to a mains socket that is safe to operate or has been installed by a
specialist in accordance with IEC 60364-1. The device may only be operated
under supervision. Do not use the appliance near a bathtub, shower, swimming
pool or sink containing water! When placing the power cord, make sure that any
water that splashes out cannot accidentally run ont he cable to the power
source. Before each use, make sure that the appliance and the mains cable and
connectors are intact. Only use undamaged devices! If you see any damage, do
not use the appliance, contact a specialist garage! During use, pay attention
to the integrity of the mains cable, avoid edges or objects that can damage
the surface of the cable. Avoid the use of extension cords or splitters, as
they are a source of danger during operation. Use only splash-proof extension
cables with a cross-section of at least 3 x 1 mm2. Always unplug the appliance
when not in use. Maintenance work must only be carried out with the mains plug
removed. It is forbidden to reach into the tank or catchment area of the
working fountain with your hands or with any objects!
Installing
- Place the fountain on a horizontal, stable, dry surface. Make sure that the appliance is stable, placed in a location where it can’t be accidentally dropped, caught in the mains cable, and possibly pulled out. Keep in mind that the mass of the fountain filled with water will be greater than the dry mass of the fountain.
- Pull the LED module onto the discharge tube inside the fountain. Check that the transparent pressure pipe is properly connected to the pump, you can control the water flow rate using the slide switch (+/-) on the side of the pump. Place the pump with the suction cups facing down into the bubble tank.
- Fill the bubbling tank with at least 7 dl of room temperature or colder water until the pump is submerged.
- Place the included glass ball on the LED unit on top of the fountain.
- The mains plug must be easily accessible so that the appliance can be easily disconnected from the power supply if necessary. The mains plug of the appliance must only be connected to a socket with a compatible voltage level. When choosing an outlet, make sure that any leaking water cannot accidentally run through the cable to the power source. The mains cable must only be connected if the pump is in the correct amount of water, otherwise, the pump may be damaged!
- Connect the mains adapter to the appropriate socket, the pump will start circulating the water and the mood light will turn on.
- If the water does not start, disconnect the mains plug from the socket, check that the pump is in the correct position and that there is enough water in the tank, and then reconnect the mains plug for ~ 15 seconds. If necessary, repeat the operation 2x 3x to bleed the system.
- Due to the natural evaporation of water during prolonged use, the amount of water must be replenished!
- If you experience a malfunction, it may be necessary to clean the device! (see „cleaning”)
Operation
Do not fill the tank with cleaning agents or chemicals! Do not drip essential
oil into the water, as this may damage the pump! Never leave the appliance
unattended when it is connected to the mains! The device may only be used
indoors, protected from environmental factors. (IPX8)
Always operate and store the device as described! Always check the integrity
of the device, cable, plug and accessories. In the event of damage, do not use
the device! Use the fountain only on a horizontal, stable surface! Be careful
not to move or rotate the appliance if there is water in the appliance, as
this may lead to electrical malfunctions. Empty the container before moving
the appliance! If the unit is accidentally moved or overturned, disconnect the
power supply (~ 230V) immediately. Do not expose the device to radiant heat
(sunshine, radiator, etc.) If necessary, seek professional assistance from a
service center. Do not reach into the slots of the guard during operation with
any object, you risk causing an accident! Do not cover the device with any
material! Do not disassemble the device! It is forbidden to change the
parameters of the device!
The manufacturer and distributor shall not be liable for any damage resulting from improper use.
Cleaning
Unplug the machine from the electrical outlet, and then drain the water from the machine’s tank. We recommend that you prepare for the operation with a towel or cloth to soak up any spilled water. Use a chemical-free, slightly damp cloth or sponge to clean the device. Clean the pump housing of the appliance and the water flow path. You can restart the device.
Disposal
Do not dispose of a defective, unrepairable appliance in the household waste
container, as it may contain components that are hazardous to the environment
or human health! For proper, environmentally sound disposal of your old
appliance, please contact your local waste collection point, where you can
return the appliance free of charge. If you have any questions, please contact
your nearest waste disposal company.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>