eufy Security Eufycam 2C Pro Wire-Free 2K Security Camera Set User Guide
- June 13, 2024
- eufy SECURITY
Table of Contents
QUICK
START GUIDE
EUFYCAM 2C PRO WIRE-FREE 2K
SECURITY CAMERA SET
PAP22
GETTING STARTED
For HomeBase 2 installation
| HomeBase 2 (T8010)
---|---
| Power Adapter for HomeBase 2
| Ethernet Cable
| Metal Pin for Resetting
For eufyCam 2C Pro installation
| eufyCam 2C Pro (T8142R)
---|---
| Micro-USB Charging Cable
| Mounting Bracket
| Mounting Screws and Anchors
- Camera quantity and accessories vary by bundle package.
- HomeBase 2 power adapter varies by region.
PRODUCT OVERVIEW
HomeBase 2
Status LED- Speaker
- Power port
- USB port
- Ethernet port
- SYNC/ALARM OFF button
- Reset button
eufyCam 2C Pro
Lens- Light sensor
- Microphone
- Motion sensor
- Spotlight
- Status LED
- SYNC button
- Mounting hole
- Charging port
- Speaker
CONNECTING THE HOMEBASE 2
Connect the HomeBase 2 to the Internet
- Power on the HomeBase 2, then use the ethernet cable provided to connect the HomeBase 2 to your home router.
- The LED indicator turns blue (this may take up to 1min) when HomeBase 2 is ready for setup
SETTING UP THE SYSTEM
Download the App and Set up the System
Download the eufy Security app from the App Store (iOS devices) or Google Play
(Android devices).
Sign up for a eufy
Security account, then follow the onscreen instructions to complete the
setup.
MOUNTING THE CAMERA
Find a Good Mounting Spot strength.
- Open the eufy Security app, go to Camera Settings > Mounting Guide.
- T o test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
- Move the camera as close to the HomeBase 2 as possible if the wireless.
Select Height and Location
Hang eufyCam 2C Pro 7-10 ft (2-3 m) above the ground. This height maximizes
the detection range of the motion sensor of eufyCam 2C Pro.
Avoid placing eufyCam 2C Pro under direct sunlight
Mount the camera
The camera can be mounted both indoors and outdoors.
- Turn the knob of the mounting bracket clockwise to loosen and disassemble it.
- Drill holes with a 15/64 inch (5.95mm) drill bit, then insert the anchors into the holes; anchors are necessary for walls that are made out of hard materials such as concrete, brick, or stucco.
- Firmly screw the base of the mounting bracket onto the wall. Fasten the ball knob of the bracket to the base of the bracket.
- Tighten eufyCam 2C Pro to the mounting bracket and adjust the viewing angle by checking the live stream feed in the eufy Security app.
Tips:
- The Homebase 2 pairs up to 16 cameras, you can repeat the steps mentioned above to add more eufyCam 2C Pro cameras to meet different needs of use.
- For troubleshooting, check Help on the eufy Security App. Refer to App page for LED indicator status.
CHARGING EufyCam 2C PRO
Charge eufyCam 2C Pro
Method 1
Method 2
| LED indication | Charging: Steady blue |
|---|
Fully charged: Off
Charging time| 5 hours
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in fixed/mobile exposure condition. The min separation
distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
The following importer is the responsible party
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004
Telephone:1-800-988-7973
** This product complies with the radio interference requirements of the
European Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. For the declaration of conformity, visit
https://uk.eufylife.com/
This product can be used across EU member states. Due to the used enclosure
material, the product shall only be connected to a USB Interface of version
2.0 or higher.
The adapter shall be installed near the equipment and shall be easily
accessible.
Do not use the Device in the environment at too high or too low temperature,
never expose the Device under strong sunshine or too wet environment.
The suitable temperature for HomeBase 2 and accessories is -10°C-45°C.
The suitable temperature for eufyCam 2C Pro and accessories is -20°C-50°C
(Charging temperature is 0°C to 40°C) .
When charging, please place the device in an environment that has a normal
room temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature
that ranges from 5°C~25°C.
Please ensure to use only the charger offered bthe manufacturer. Using
unauthorized charger may cause danger and violate the authorization of the
device and the guarantee article.
This charger is for indoor use only.
The charger type is KA 2401A-1202000DE, output voltage/current is 12Vdc/2A.
The plug considered as disconnect device of adapter.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human
body.
To maintain compliance with RF exposure requirement, use product that maintain
a 20cm distance between the device and human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Wi-Fi Operating Frequency Range: 2412~2472MHz; Wi-Fi Max Output Power: 18.23
dBm (ERIP for T8010), 19.02 dBm (ERIP for T8142R)
SUB-1G Frequency range: 866~866.8MHz; SUB-1G Output Power: 5.24 dBm (ERIP for
T8010)
The following importer is the responsible party (contact for EU matters only)
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich,
Germany
** This product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
** This symbol means the product must not be discarded as household waste,
and should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device. ”
This Class B digital apparatus complies with Canadian ICES-003.
IC RF Statement:
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
** This product complies with the radio interference requirements of the
United Kingdom.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product is in compliance
with Radio Equipment Regulations 2017. The full text of the UK declaration of
conformity is available at the following internet address:
https://uk.eufylife.com
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom
Customer Service
Kundenservice
Warranty
Garantie
12-month limited warranty
12 Monate eingeschränkte Garantie
Call Us
Rufen Sie uns an
Email Us
Senden Sie uns eine E-Mail
Customer Support: support@eufylife.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
@EufyOfficial
@EufyOfficial
**** @EufyOfficial
Anker Innovations Limited. All rights reserved. eufy Security and eufy
Security Logo are trademarks of Anker Innovations Limited, registered in the
United States and other countries. All other trademarks are the property of
their respective owners.
51005002536 V05
References
- eufy | Built with Care | Up to 53% Off | eufy UK
- eufy | Built with Care | Up to 53% Off | eufy UK
- eufy | Built with Care | Up to 53% Off | eufy UK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>