RAB R34-6B Carbonate 5 W LED Ceiling Downlight Instruction Manual
- June 13, 2024
- RAB
Table of Contents
RAB R34-6B Carbonate 5 W LED Ceiling Downlight
Product Information
This product is a modified luminaire designed to operate LED lamps. It is not
compatible with incandescent lamps. The product is manufactured by RAB
Lighting Inc., and the model number is R34-6.
The package includes the following items:
- Downlight (1)
- E26 Adaptor (1)
- Lumi Sticker (1)
Optional accessories:
- 6 Band with Friction clips (RFLED-RETROBAND)
- Color trim (DLTRIMR6RS-xx-L)
Product Usage Instructions
- Ensure you have the necessary tools, including a screwdriver.
- Remove the existing trim and bulb from the recessed housing.
- Unscrew the screws on the socket bracket and push the bracket upward to the top location.
- Remove the existing socket mounting plate from the recessed housing, along with the lamp socket.
- Screw the E26 adaptor into the socket inside the housing.
- Select the desired color temperature (CCT) level using the switch on the driver box.
- Plug the E26 base cable connection into the recessed housing.
- Squeeze the torsion springs as shown and install them into the metal brackets inside the recessed housing. Ensure the springs are seated within the brackets and on both sides of the housing.
Note: These instructions provide a general overview of the installation process. Refer to the dimensional drawings for specific measurements and consult a professional if needed.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS
- Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing.
- To prevent early lamp failure, lamp should only be installed in operating environments ranging between -4°F and +104°F [-20°C and +40°C).
- No user-serviceable parts inside. To avoid electrical shock do not disassemble the product.
- Risk of fire or electric shock, LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Risk of fire or electric shock, Install this kit only in luminaires that have the construction features and minimum dimensions shown in Figure-1 and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Installers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals, Instead installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing applicable connectors.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
- This device is not intended for use with emergency exits.
- These retrofit kits are suitable for wet locations luminaires specified as below: Type Non-IC; Type IC; Covered ceiling; Uncovered ceiling.
- Installers should examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
WHAT’S IN THE BOX
TOOLS NEEDED
The Recessed LED Downlight is designed to fit into a 6” housing. No tools
are necessary for installation.
MINIMUM LUMINAIRE DIMENSION
OPTIONAL ACCESSORIES
INSTALLATION INSTRUCTIONS
- Make sure the power is turned off at the source to the recessed housing(s) that you are installing the fixture(s) in. Remove existing trim and bulb.
- Unscrew the screws on socket bracket, push bracket upward to the top location. (Fig. 2)
- Remove existing socket mounting plate from the recessed housing and then remove lamp socket from the plate.
- Screw the E26 adapter into the socket inside the housing.
- Select desired color temperature (CCT) level using switch on driver box.
- Plug E26 base cable connection into the recessed housing.
- Squeeze torsion springs as shown and install into the metal brackets inside the recessed housing. For proper installation, the torsion springs should be seated within the brackets and on both sides of the housing. (Fig. 7)
- Carefully place wires into fixture and push the LED trim into the housing until flush with ceiling.
DIMENSIONAL DRAWINGS
FCC
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
© 2023 RAB LIGHTING Inc.
Cranbury, New Jersey 08512 USA R34-6x-IN-0723
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found
at rablighting.com/warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>