BEGA 50032K2 Ceiling and Wall Luminaire for Indoor Use Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

Application
Product description
Safety
Overvoltage protection
Installation
Accessory · Trim rings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Technical amendments reserved
50 032
Ceiling and wall luminaire for indoor use

BEGA 50032K2 Ceiling and Wall Luminaire for Indoor Use

Instructions for use

Application

Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.

Product description

Metal housing, finish colour white
Hand-blown opal glass, satin matt, with bayonet closure 2 mounting holes ø 5.5 mm
Distance apart 230 mm
2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
Safety class I
Impact strength IK05
Protection against mechanical impacts < 0.7 joule
– Safety mark
**** – Conformity mark
Weight: 3.2 kg

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage	26.4 W
Luminaire connected wattage	31.1 W
Rated temperature	ta = 25 °C
Ambient temperature	ta max = 30 °C

50 032 K3

Colour temperature	3000 K
Colour rendering index	CRI > 90
Module luminous flux	3970 lm
Luminaire luminous flux	2592 lm
Luminaire luminous efficiency	83,3 lm / W

50 032 K2

Colour temperature	2700 K
Colour rendering index	CRI > 90
Module luminous flux	3845 lm
Luminaire luminous flux	2510 lm
Luminaire luminous efficiency	80,7 lm / W

50 032 K4

Colour temperature	4000 K
Colour rendering index	CRI > 90
Module luminous flux	4135 lm
Luminaire luminous flux	2700 lm
Luminaire luminous efficiency	86,8 lm / W

Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on to the mounting surface.
It is imperative to use the enclosed gaskets. Dismantle the mains supply cable approx. 60 mm.
Pull silicone sleeves over the wires and make earth and electrical connection to the terminals.
Place glass to the luminaire housing and observe that the cam pins fit into the notches of the glass.
Screw in glass by turning it clockwise.
Thus, you reach a safe and vibration- resistant holding of the glass.
To release the glass from the luminaire housing, turn it counter-clockwise.

Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.
Disconnect from main supply.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Replace the LED unit.
Screw in glass by turning it clockwise.
Defective glass must be replaced.