ONFORU CT06 Black Light Bar User Manual
- June 13, 2024
- ONFORU
Table of Contents
CT06 Black Light Bar
User Manual
CT06 Black Light Bar
LED LIGHT
Product Manual
MODEL: CTB24UV CTB27UV CTB48UV
CTB72UV CTB96UV
COMPONENTS AND STRUCTURE
PARTS LIST (CTB24UV CTB27UV CTB48UV)
PARTS LIST (CTB72UV CTB96UV)
SPECIFICATIONS
LED FLOODLIGHT
Model| CTB24UV| CTB27UV| CTB48UV
Input Voltage| 100-120V～60Hz
Input Current| 0.2A| 0.22A| 0.42A
Rated Power| 24W| 27W| 48W
Wavelength| 385-400nm
Power Factor| ≥0.9
Chromaticity coordinate|
x=0.1763 y=0.0317
CRI| -1.9
Beam Angle| 120°
t a| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR DAMP LOCATIONS
DIMENSIONS
Model| CTB24UV| CTB27UV| CTB48UV
Dimensions （LxWxH）| 4306676mm/ 10.932.582.99in| 3944450mm/
15.511.731.97in| 4308076mm/ 10.933.152.99in
Weight| 0.53KG/1.17lb| 0.465KG/1.025lb| 0.9KG/1.98lb
Note:
The intended purpose of this special purpose product: This light is used to
create atmosphere. it is not suitable for household room illumination the
light source is not intended for use in other applications.|
LED FLOODLIGHT
Model| CTB72UV| CTB96UV
Input Voltage| 100-120V～60Hz
Input Current| 0.6A| 0.82A
Rated Power| 72W| 96W
Wavelength| 385-400nm
Power Factor| ≥0.9
Chromaticity coordinate| x=0.1763 y=0.0317
CRI| -1.9
Beam Angle| 120°
t a| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR DAMP LOCATIONS
DIMENSIONS
Model| CTB72UV| CTB96UV
Dimensions （LxWxH）| 430110110mm/ 10.934.334.33in| 430140110mm/
10.935.54.33in
Weight| 1.21kg/2.67lb| 1.6kg/3.53lb
Note:
The intended purpose of this special purpose product: This light is used to
create atmosphere. it is not suitable for household room illumination the
light source is not intended for use in other applications.|
PREPARATION
Check all components for damage, do not use the productivity is damaged.
Estimated Assembly Time:10-30 minutes
TOOLS REQUIRED（not included）
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
RISK OF SHOCK- BEFORE BEGINNING INSTALLATION,TURN OFF ELECTRICITY AT THE
CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT MAIN CIRCUIT BREAKER BOTH ARE
OFF.
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN.
WARNING: INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY CAUSE
THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS
ARE DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE
AN ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH. BE CAREFUL NOT TO DAMAGE OR
CUT THE WIRE INSULATION (COVERING) DURING INSTALLATION. DO NOT LET THE WIRES
TOUCH ANY SHARP EDGES.
INSTALLATION STEPS
Product appearance may vary from image shown.
STEP 1:
Fix the bracket on the lamp with the combination screw. (as shown in the
image)
STEP 2:
According to the spacing (see the “F” part of the picture) of two holes on the
lamp brackets, drill two mounting holes. (as shown in the image)
STEP 3:
Put the brackets onto the prepared mounting holes and then screw them on.
STEP 4:
Adjust the beam direction as you like, and then plug into the main socket.
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
HK Bright International Lighting Co., Limited
Unit 616, 6/F., Kam Teem Industrial Building, 135
Connaught Road West, Sai Wan Hong Kong
Manufacturer/Hers teller: MDH LIGHTING LTD
Suite 302, 292 Stroviols Avenue, 2048 Stroviols Nicosia, Cyprus
UK Importer: MDH LIGHTING LTD
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom
Made in China
support@onforuled.com
www.onforuleds.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>