ONFORU CTB24UV LED Light Instruction Manual
- June 5, 2024
- ONFORU
Table of Contents
ONFORU CTB24UV LED Light
COMPONENTS AND STRUCTURE
PARTS LIST
SPECIFICATIONS
LED FLOODLIGHT
Model| CTB24UV| CTB48UV| CTB72UV| CTB96UV
Input Voltage| 100-120V~60Hz
Input Current| 0.2A| 0.42A| 0.6A| 0.82A
Rated Power| 24W| 48W| 72W| 96W
Wavelength| 385-400nm
Power Factor| ≥0.9
Chromaticity coordinate| x=0.1763 y=0.0317
CRI| -1.9
Beam Angle| 120°
t a| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR WET LOCATIONS
DIMENSIONS
Model| CTB24UV| CTB48UV| CTB72UV| CTB96UV
Dimensions
(LxHxW)
| 4306676mm/
10.932.582.99in
| 4308076mm/
10.933.152.99in
| ****
430110110mm/
10.934.334.33in
| 430140110mm/
10.935.54.33in
Weight| 0.53KG/1.17lb| 0.9KG/1.98lb| 1.21kg/2.67lb| 1.6kg/3.53lb
Max Projected Area| 0.0255m²/0.2744ft²| 0.0309m²/0.333ft²| 0.0425m²/0.457ft²|
0.0542m²/0.583ft²
Note:
The intended purpose of this special purpose product:This light is used to create atmosphere. it is not suitable for household room illumination,the light source is not intended for use in other applications.
| ****
PREPARATION
Check all components for damage, do not use the product if it is damaged.
Estimated Assembly Time:10-30 minutes
TOOLS REQUIRED(not included)
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED. RISK OF SHOCK- BEFORE BEGINNING INSTALLATION, TURN
OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
CAUTION:
- PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT
- MAIN CIRCUIT BREAKER BOTH ARE OFF.
- IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT
- A LICENSED ELECTRICIAN.
- WARNING: INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY CAUSE THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH.
- BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULATION (COVERING) DURING INSTALLATION. DO NOT LET THE WIRES TOUCH ANY SHARP EDGES.
INSTALLATION STEPS
Product appearance may vary from image shown.
-
STEP 1:
Fix the bracket on the lamp with the combination screw. (as shown in the image) -
STEP 2:
According to the spacing (see the “A” part of the picture) of four holes on the lamp brackets, drill four mounting holes. (as shown in the image) -
STEP 3:
Put the brackets onto the prepared mounting holes and then screw them on. -
STEP 4:
Adjust the beam direction as you like, and then plug into the main socket.
NOTE:
Recommended installation height not higher than 5 m (16.4 ft).
Manufacturer
Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si
Address : qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo
qu Shen Zhen, Guang Dong, 518000, CN
support@onforuled.com
www.onforuleds.com
EU REP MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos icosia, Cyprus |
support@onforuled.com
69 Aberdeen Avenue, Cambridge CB2 8DL, United Kingdom |
support@onforuled.com
Made in China