ONFORU CTB96BL 2 Pack LED Flood Light Instruction Manual
- June 4, 2024
- ONFORU
Table of Contents
CTB96BL 2 Pack LED Flood Light
Instruction Manual
LED LIGHT
Product Manual
MODEL: CTB24BL, CTB72BL ,CTB48BL ,CTB96BL
COMPONENTS AND STRUCTURE
PARTS LIST
SPECIFICATIONS
LED FLOODLIGHT
Model| CTB24BL| CTB48BL| CTB72BL| CTB96BL
Input Voltage| 100-120V – 60Hz
Input Current| 0.31A| 0.6A| 0.9A| 1.1A
Rated Power| 24W| 48W| 72W| 96W
Color| RGB
Power Factor| a0.5
Chromaticity coordinate| x=0.2053, y=0.192
Beam Angle| 120°
ta| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR WET LOCATIONS
DIMENSIONS
Model| CTB24BL| CTB48BL| CTB72BL| CTB96BL
Dimensions
1LxHxWi| 430’66’76mnV
10.93’2.58’2.99in| 430’80’76mnV
10.93’3.15’2.99in| 430’110’110mm/
10.93’4.33’4.33in| 430’140110mny
10.93’5.5’4.33in
Weight| 0.53KG/1.17Ib| 0.9KG/1.98Ib| 1.21kg/2.671b| 1.6kg/3.53Ib
Max “acted
Area| 0.0255m2/0.2744ft2| 0.0309m2/0.333ft2| 0.0425m2/0.4571t2|
0.0542m2/0.583ft2
Note:
The intended purpose of this special purpose product: This light is used to
create an atmosphere. it is not suitable for household room illumination, the
light source is not intended for use in other applications.|
APP INSTALLATIONS
STEP 1
- Please scan the QR code.
- Search for ” Happy Lighting ” in the Apple Store or Google Play.
- Download and install the App, as shown in the picture.
http://download.appglobalmarket.com/happylightingdownload.html
STEP 2
Note:
- Before using the app, please make sure that the Bluetooth of your mobile phone Is enabled.
- Unable to connect to Bluetooth: After you open the app and select the color, the color doesn’t change on the flood light, it means that the Bluetooth fails to connect. The light might have been connected to the other phone.
1. You need to disconnect the Bluetooth of the other phone, and then your phone will be automatically connected to the light. At this time, when you turn on the Bluetooth, it will show that the device Trick -XXXX is conne ted, which means that the Bluetooth is connected now.
2. Open the APP and place the phone near the light, it will be connected to the nearest Bluetooth without blocking, after the light is turned off and turned on again.
APP OPERATING INSTRUCTIONS
Brightness Selection Interface:
You could adjust the brightness.
Music Mode Interface :
You could control the brightness and dynamic changes of the light by playing
local music in the phone.
Dynamic Mode Interface:
The light has 5 dynamic modes (Gradient, Breathing, Strobe, Jump, Auto), and
speed can be adjusted.
Mobile Speaker:
The dynamic modes can change with the sound inside the phone or other external
sounds.
Timing Interface
You can turn on or turn off the light regularly.
PREPARATION
Check all components for damage, do not use the product if it is damaged.
Estimated Assembly Time:10-30 minutes
TOOLS REQUIREDcnot included
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED. RISK OF SHOCK- BEFORE BEGINNING INSTALLATION, TURN
OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT MAIN CIRCUIT BREAKER BOTH ARE
OFF. IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED
ELECTRICIAN.
WARNING: INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY
CAUSE THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE
CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT
WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH.
BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULATION (COVERING) DURING
INSTALLATION. DO NOT LET THE WIRES TOUCH ANY SHARP EDGES.
INSTALLATION STEPS
Product appearance may vary from the image shown.
Step 1: Fix the bracket on the lamp with the combination screw. (as shown
in the image)
Step 2 : According to the spacing (see the “A” part of the picture) of
four holes on the lamp brackets, drill four mounting holes. (as shown in the
image)
Step 3: Put the brackets onto the prepared mounting holes and then screw
them on.
Step 4 : Adjust the beam direction as you like, and then plug into the
main socket.
NOTE: Recommended installation height not higher than 5 m (16.4 ft).
FCC ID: 2A3W8D100BLA
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
** Manufacturer / Hersteller:
Shenzhen ShiMeng ZhiTuo KeJiYou Xian Gong Si
Address: qianwanyilu 1 hao A dong 201 shiqianhai Shenyang hezuoqu Shenzhen,
Guang Dong, 518000
CN support@onforuled.com
www.onforuleds.com
` EU REPMDH LIGHTING LTD Suite 302, 292 Strovolos Avenue, 2048 Strovolos Nicosia, Cyprus [support@onforuled.com](mailto:support@onforuled.com)
UK REP**` MDH LIGHTING LTD
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom
support@onforuled.com
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>