ONFORU CTB48RGBU RGB UV LED Light Instruction Manual

Model: CTB48RGBU

RGB+UV LED LIGHT
Product Manual

SAFETY INFORMATION

Disconnect the power supply before attempting any work on the unit！

• Installing these units involves work on the mains voltage supply; installation must therefore be carried out professionally in accordance with the appliance national wiring regulations and electrical operating conditions.
• The product must be installed by a licensed professional electrician.
• Check all components for damage, do not use the product if it is damaged.
• To ensure the product can work normally, please use it in the voltage within the range on the lamp label.
• The floodlight enclosure heats up when the light is on.Please adjust the angle of the light after the power off for 10-15 minutes.
• Do not look into the LED light at a short range or any prolonged period(>5 min).
• Do not install the unit on (normally) flammable surfaces. Do not alter or change parts of the light at will, in case of the accidents such as breakage, fall, electric shock, fire, etc.
• To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach
• The light is IP66 waterproof, but the plug is non-waterproof. Please connect the plug indoor or connect to a socket that provides IP65 protection. Please use tools to adjust the lights.
• The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced. Never plug the light in with wet hands in case of electric shock.
• This light is a non-dimmable product. To avoid failure, please don’t connect it with the dimming controller.
• Do not connect this light fixture to an ungrounded electrical system. WARNING: Installing this light in an ungrounded electrical system may cause the metal parts of the light to carry current if any wires or wire connections are damaged or loose. In this case, anyone who touches the light will receive an electric shock, resulting in injury or death.
• Be sure to use wire nuts/connectors rated for the correct gauge and number of wires used. NOTE: Make sure there are no exposed wire bundles outside the wire nut/connector (if applicable).
• Be careful not to damage or cut the wire insulation (covering) during installation. Do not let the wires touch any sharp edges.
• The floodlight is supplied with cable and must be terminated using a terminal block (not supplied) in a suitable IP rated enclosure (not included).
• For type Z attachments： The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.

PARAMETER

| 430x80x79 mm        16.93×3.15×3.11 in
---|---
| 1.0 kg   2.20 lb
| 100-120V AC 60Hz   220-240V AC 50Hz
| RGB+UV
| IP66
ta| -25°C – 40°C/-4°F-104°F
PF| >0.5
CRI| -1.9
chromaticity coordinate| x=0.1763  y=0.0317

Max Projected Area
A: 0.0255m² B: 0.0309m² C: 0.0346m² D: 0.0542m²

COMPONENTS AND STRUCTURE

1. Tempered Glass Lid
2. LED Light Source
3. Lamp Bracket
4. Screws For Mounty
5. Plastic Expansion Nails
6. Screws
7. Lamp Brackets
8. M5 Hex Screw Key
9. Remote Control

With the Memory function, the light can start at your last choice of color and mode.

1. Brightness Adjustment: Press the “ ” or “ ” to either increase or decrease the brightness; There are 8 levels of adjustable brightness.
2. Stop: Pause color changes in the jump mode, fade mode, flash mode, or automatic mode.
3. On/Off: Turn on or off the light by pressing ” “
4. Color Options: Press the colored buttons to select the corresponding light.
5. DIY Mode: After pressing the button DIY1 \ DIY2 \ DIY3, you can DIY different colors by adjusting the RGB brightness through these 6 keys, and these colors are automatically saved; there are 17 variations of colors, and more than 4,800 colors are available for you to choose. 3 kinds of DIY colors can be saved as DIY1 \ DIY2 \ and DIY3.
6. Switch to UV light mode
7. Timing: There are 3 regular intervals of 2H\4H\6H to set the timer and the light will be off automatically when the time is up.
8. If the light flashes continuously, the flashing speed can be adjusted by “QUICK/SLOW”.
9. Flash Mode: Make the light flash. 10. Auto Mode: Freely switch Jump Mode, Fade Mode, or Flash Mode.
10. Jump Mode: JUMP is the mode of seven-color jumps.
11. Speed Adjustment: Adjust the speed of color changes in Jump Mode, Fade Mode, and Flash Mode; press the button QUICK to speed up and SLOW to slow down. And 30 kinds of different speeds are available for you to choose.
12. Fade Mode: FADE3 is the mode of three color gradients, and FADE3 is the mode of seven color gradients.
13. Remove the insulation sheet before using the remote control.

Replace the batteries of the remote control by referring to the figure on the right.

NOTE  

01 – Make sure that the distance between the light and the object being lit is more than 1 meter, so as to avoid high temperature caused by short distance..
02 – Earth wire is required for connection for electric safety.
03 – Lights that are not suitable for covering with thermal insulation materials.
04 – Lights that are not suitable for being directly installed on normally flammable surfaces (only suitable for being installed on a non-flammable surface)

INSTALLATION STEPS 

Step 1: Fix the bracket on the lamp with the combination screw. (as shown in the image)
Step 2: According to the spacing (see the “A” part of the picture) of four holes on the lamp brackets, drill four mounting holes. (as shown in the image)
Step 3: Put the brackets onto the prepared mounting holes and then screw them on.
Step 4: Adjust the beam direction as you like, and then plug into the main socket.
NOTE: Recommended installation height not higher than 5 m (16.4 ft)

OPERATION & MAINTENANCE

• Prior to cleaning the light, make sure it has been disconnected from the power supply.
• The unit is not suitable for burglar alarm systems as it is not tamperproof in the manner prescribed for such systems.
• Never use any chemicals or corrosive substances for cleaning.

DISPOSAL

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner.
Do not dispose of electrical and electronic equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste Electrical and Electronic equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Manufacturer / Hersteller:
Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si
Address: qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo qu Shen Zhen, Guang
Dong, 518000, CN
support@onforuled.com www.onforuleds.com
MDH LIGHTING LTD
MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus | support@onforuled.com
UK REP MDH LIGHTING LTD
MDH LIGHTING LTD
UNIT G25 WATERFRONT STUDIOS 1 DOCK ROAD
LONDON UNITED KINGDOM E16 1AH|support@onforuled.com
Made in China

Documents / Resources

| ONFORU CTB48RGBU RGB UV LED Light [pdf] Instruction Manual
CTB48RGBU, RGB UV LED Light, CTB48RGBU RGB UV LED Light, UV LED Light, LED Light, Light
---|---

References

• Onforu LED Light - Colorful LED Lights Make Your Life More Colorful

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>