ONFORU D100BL LED Flood Light User Manual
- October 30, 2023
- ONFORU
Table of Contents
**ONFORU D100BL LED Flood Light User Manual
**
Components and Structure
- Cover
- LED Light Source
- Lamp Bracket
Specifications
Model| Input Voltage| Input Current| Rated Power| Luminous Flux| CCT| CRI|
Color| Power Factor| Beam Angle| Luminaire Location| Dimensions (LxHxW)|
Weight
---|---|---|---|---|---|---|---|---|---|---|---|---
D30BL| 100-120V60Hz| 0.32A| 25W| 2000lm| 2700K| 80| RGB| 0.5| N/A| Suitable
for wet locations| 205x30x125 mm / 8.07×1.18×4.92 in| 0.49 kg / 1.08 lb
G50BL| 100-120V60Hz| 0.56A| 50W| 4000lm| 2700K| 80| RGB| 0.5| N/A| Suitable
for wet locations| 230x35x139 mm/ 9.06×1.36×5.47 in| 0.95KG /2.09lb
D50BL| 100-120V60Hz| 0.56A| 50W| 4000lm| 2700K| 80| RGB| 0.5| N/A| Suitable
for wet locations| 208x127x37 mm/ 8.19x5x1.46in| 0.58 kg / 1.28 lb
D100BL| 100-120V60Hz| 1.07A| 100W| 7200lm| 2700K| 80| RGB| 0.5| N/A| Suitable
for wet locations| 289x39x177 mm/ 11.38×1.54×6.97in| 1.2 kg / 2.65 lb
App Installations
App Operating Instructions
Brightness Selection Interface：
You could adjust the brightness.
Music Mode Interface：
You could control the brightness and dynamic changes of the light by playing
local music in the phone.
Dynamic Mode Interface:
The light has 5 dynamic modes (Gradient, Breathing, Strobe, Jump, Auto), and
speed can be adjusted.
Mobile Speaker:
The dynamic modes can change with the sound inside the phone or other external
sounds.
Timing Interface：
You can turn on or turn off the light regularly
How to Control Lights in Groups
If you use the app to connect 2 or more lights, the app will default these lights as a group, and you can control these lights at the same time.
If you want to control one of the lights separately, select the light first and then control it.
Preparation
Check all components for damage, do not use the product if it is damaged. Estimated Assembly Time:10-30 minutes
TOOLS REQUIRED（not included）
-
Flathead screwdriver
-
Screwdriver
-
Electric drill
-
Eye protection
-
Pliers
-
Step ladder
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT MAIN CIRCUIT BREAKER BOTH ARE
OFF. IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN
WARNING:
INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY CAUSE THE METAL
PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS ARE
DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN
ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH. BE CAREFUL NOT TO DAMAGE OR CUT
THE WIRE INSULATION (COVERING) DURING INSTALLATION. DO NOT LET THE WIRES TOUCH
ANY SHARP EDGES.
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED. RISK OF SHOCK- BEFORE BEGINNING INSTALLATION,TURN
OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
INSTALLATION STEPS
Step 1: According to the spacing (see the “A” part of the picture) of two
screw bits on the LED Light bracket, drill two mounting holes.
Step 2: Put the bracket onto the prepared mounting holes and then screw
it on.
Step 3: Adjust the beam direction as you like, Wiring.
Step 4: Adjust the beam direction as you like, and then plug intothe main
socket.
FCC ID: 2A3W8D100BLM
FCC Warning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
HK Bright International Lighting Co., Limited Unit 616, 6/F., Kam Teem
Industrial Building, 135 Connaught Road West, Sai Wan Hong Kong
Manufacturer/Hersteller: MDH LIGHTING LTD Suite 302, 292 Strovolos Avenue,
2048 Strovolos Nicosia, Cyprus
UK ImporterMDH LIGHTING LTD 69 Aberdeen Avenue, Cambridge CB2 8DL, United
Kingdom
Made in China
E-mail: support@onforuled.com
Web: www.onforuleds.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>