ONFORU DT15UV UV LED Strip Light User Manual
- June 5, 2024
- ONFORU
Table of Contents
UV LED STRIP LIGHT
Product Manual
MODEL:
DT5UV/DT10UV
DT15UV
**** SAFETY INFORMATION
- Don’t roll the light strip during the operation, otherwise, it will melt.
- Don’t cover the light strip as the covering may cause the light strip to overheat and melt or ignite.
- Don’t immerse the light strip in the liquid, or use it near water or other liquids.
- Please use our power adapter, controller or dimmer, the power of the strip light cannot be higher than the maximum power of the adapter, controller or dimmer.
- Only use the provided hanger or clip to protect the light strip. Do not use staples, nails or similar things to fix this product or its wires, which may damage the insulation.
- Risk of fire – do not replace the plug. The plug contains a safety device (fuse) that should not be removed. Discard the product if the plug is damaged.
- Please pay attention to anti-static during the installation and use of the product. Don’t touch the product with sharp tools.
COMPONENTS
- LED Light Strip
- Fasteners
- Power Adapter
- Controller
- Remote Control
CONNECTION DIAGRAM
Note: Please keep the arrow and arrow connect in the same direction or the light won’t work.
REMOTE CONTROL OPERATION
- ON/OFF
- Steady on
- Strobe
- Fade
- B+/B-: Adjust brightness
- S+/S-:Adjust speed
- Flash
- Flicker
- Timing: 2H/4H/8H
- Remove the insulation sheet before using the remote control.
Replace the batteries of the remote control by referring to the figure on the right.
NOTE
01 Safety Class III = Only operate lamps with this symbol with Safety Extra
Low Voltage (SELV). Only connect to SELV circuits.
02 Safety Class II=This lamp is doubly insulated and may not be wired to a
protective conductor.
- Please install the lights on the dust-free, clean and smooth surface, otherwise the strips will fall.
- During the installation, the bend should be avoided to be just in the position of LEDs or other components.
INSTALLATION STEPS
-
Stick the LED strip on a suitable surface.
A. Knitted / Wool fabrics
B. Dusty wall
C. Rough plastic surface
D. Frosted glass
-
Fix the adapter in the right way
-
Please clean the mounting surface before installation.
-
Tear the plastic sheet bit by bit
-
stick the LED strip and press with force
-
Two fixing methods
A: Adhesive method: peel off the sticker on the back of the buckle, and then stick the light strip on the walll.
B: Adhesive & screw fixing method: peel off the sticker on the back of the buckle, stick the strip light on the wall, and then fix it with screws. -
Please use the foam tape included in our package to fasten the strip if it doesn’t sticks well.
-
Press the whole LED strip repeatedly
Operation & Maintenance
Never use any chemicals or corrosive substances for cleaning.
DISPOSAL
Electrical and electronic equipment, accessories, and packaging must be
recycled in an environmentally compatible manner.
Do not dispose of electrical and electronic equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste Electrical and Electronic
equipment and its implementation in national law, electrical and electronic
equipment no longer suitable for use must be collected separately and recycled
in an environmentally compatible manner.
Manufacturer: Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si
Address: qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo qu Shen
Zhen, Guang
Dong, 518000, CN
support@onforuled.com
www.onforuleds.com
European Representative:
BellaCocool GmbH
Pettenkoferstraße 18, 10247, Berlin, Germany
support@onforuled.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>