ONFORU D30UVBL 2 Pack 50W LED Flood Light Instruction Manual
- June 4, 2024
- ONFORU
Table of Contents
ONFORU D30UVBL 2 Pack 50W LED Flood Light
COMPONENTS AND STRUCTURE
SPECIFICATIONS
LED FLOODLIGHT
Model| D30UVBL| G50UVBL| D100UVBL
Input Voltage| 100-120V～60Hz
Input Current| 0.31A| 0.6A| 1.1A
Rated Power| 25W| 50W| 90W
Wavelength| 385-400nm
Power Factor| ≥0.5
Chromaticity coordinate| x=0.1763 y=0.0317
CRI| -1.9
Beam Angle| 120°
t a| -20-40°C/-4°F-104°F
Luminaire Location| SUITABLE FOR WET LOCATIONS
DIMENSIONS
Model| D30UVBL| G50UVBL| D100UVBL
Dimensions（LxHxW）
| 258x168x40mm / 10.15×6.61×1.57in| 230x138x35mm / 9.06inx5.47×1.38in|
329x208x35mm/ 12.95×8.18×1.377in
Weight| 0.5KG/1.1lb| 0.65KG/1.43lb| 1.47kg/3.24lb
Max Projected Area| 0.0189m²/0.2034ft²| 0.0243m²/0.262ft²| 0.0616m²/0.663ft²
Note:
The intended purpose of this special purpose product:This light is used to
create atmosphere. it is not suitable for household room illumination，the light source is not intended for use in
other applications.
| ****
APP INSTALLATIONS
STEP 1
- Please scan the QR code.
- Search for “Trick Light” in the Apple Store or Google Play.
- Download and install the App, as shown in the picture.
STEP 2
Note: Before using the app, please make sure that the Bluetooth of your
mobile phone is enabled. Unable to connect to Bluetooth: After you open the
app and select the color, the color doesn’t change on the tlood light, it
means that the Bluetooth fails to connect. The light might has been connected
to the other phone.
- You need to disconnect the Bluetooth of the other phone, and then your phone will be automatically connected to the light. At this time,when you turn on the Bluetooth, it will show that the device Trick-xXXX IS conne ted, which means that the Bluetooth is connected now. 2.0pen the APP and place the phone near the light, it will be connected to the nearest Bluetooth without blocking, after the light is turned off and turned on again.
APP OPERATING INSTRUCTIONS
Brightness Selection Interface ：You could adjust the brightness.
Music Mode Interface： You could control the brightness and dynamic
changes of the light by playing local music in the phone.
Dynamic Mode Interface: The light has 5 dynamic modes (Gradient, Breathing, Strobe, Jump, Auto), and speed can be adjusted.
Mobile Speaker: The dynamic modes can change with the sound inside the phone or other external sounds.
Timing Interface： You can turn on or turn off the light regularly.
PREPARATION
Check all components for damage, do not use the product if it is damaged. Estimated Assembly Time:10-30 minutes
TOOLS REQUIRED（not included）
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED. RISK OF SHOCK- BEFORE BEGINNING INSTALLATION,TURN
OFF ELECTRICITY AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT MAIN CIRCUIT BREAKER BOTH ARE
OFF. IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED
ELECTRICIAN.
WARNING: INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL SYSTEM MAY CAUSE THE METAL PARTS OF THE LIGHT TO CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS ARE DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES THE LIGHT WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN INJURY OR DEATH. BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULATION (COVERING) DURING INSTALLATION. DO NOT LET THE WIRES TOUCH ANY SHARP EDGES.
INSTALLATION STEPS
Product appearance may vary from image shown.
- STEP 1: According to the spacing (see the “A” part of the picture) of two screw bits on the LED Light bracket, drill two mounting holes.
- STEP 2 : Put the bracket onto the prepared mounting holes and then screw it on.
- STEP 3: Adjust the beam direction as you like, and then plug into the main socket.
NOTE: Recommended installation height not higher than 5 m (16.4 ft).
FCC Warning
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Manufacturer
support@onforuled.com www.onforuleds.com
MDH LIGHTING LTD
69 Aberdeen Avenue, Cambridge CB2 8DL, United Kingdom | support@onforuled.com Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>