ONFORU D30BL LED RGB Flood Light Instruction Manual

June 5, 2024
ONFORU

MODEL: D30BL

LED RGB FLOOD LIGHT

Product Manual

US 100-120V AC

EU 220-240V AC

UK 220-240V AC

SAFETY INFORMATION

Disconnect the power supply before attempting any work on the unit !

  • Installing these units involves work on the mains voltage supply; installation must therefore be carried out professionally in accordance with the appliance national wiring regulations and electrical operating conditions.

  • The product must be installed by a licensed professional electrician.

  • Check all components for damage, do not use the product if it is damaged.

  • To ensure the product can work normally, please use it in the voltage within the range on the lamp label.

  • The floodlight enclosure heats up when the light is on.Please adjust the angle of the light after the power off for 10-15 minutes. Do not look into the LED light at a short range or any prolonged period(>5 min).

  • Do not install the unit on (normally) flammable surfaces.

  • Do not alter or change parts of the light at will, in case of the accidents such as breakage, fall, electric shock, fire, etc.

  • To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach

  • The light is IP66 waterproof, but the plug is non-waterproof. Please connect the plug indoor or connect to a socket that provides IP65 protection.

  • Please use tools to adjust the lights.

  • The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.

  • Never plug the light in with wet hands in case of electric shock.

  • This light is a non-dimmable product. To avoid failure, please don’t connect it with the dimming controller.

  • Do not connect this light fixture to an ungrounded electrical system.
    WARNING: Installing this light in an ungrounded electrical system may cause the metal parts of the light to carry current if any wires or wire connections are damaged or loose. In this case, anyone who touches the light will receive an electric shock, resulting in injury or death.

  • Be sure to use wire nuts/connectors rated for the correct gauge and number of wires used.
    NOTE: Make sure there are no exposed wire bundles outside the wire nut/connector (if applicable).

  • Be careful not to damage or cut the wire insulation (covering) during installation. Do not let the wires touch any sharp edges.

  • The floodlight is supplied with cable and must be terminated using a terminal block (not supplied) in a suitable IP rated enclosure (not included).

  • For type Z attachments:
    The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.

  • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FCC Warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

PARAMETER

| 205x30x218 mm / 8.07×8.58×1.18 in
---|---
| 0.54 kg / 1.21 lb
| 100-120V ~ 60Hz 220-240V ~ 50Hz
| RGB/2700K
| IP66
ta| -25°C – 40°C/-4°F-104°F
PF| >0.5
Max Projected Area| 0.0189m2

APP INSTALLATION
  1. Please scan the QR code.
  2. Search for “HAPPY LIGHTING” in the Apple Store or Google Play.
  3. Download and install the App, as shown in the picture.

ONFORU D30BL LED RGB Flood Light 5A

Note:

  • Before using the app, please make sure that the Bluetooth of your mobile phone is enabled.
  • Unable to connect to Bluetooth:
    After you open the app and select the color, the color doesn’t change on the flood light, it means that the Bluetooth fails to connect. The light might has been connected to the other phone.
  1. You need to disconnect the Bluetooth of the other phone, and then your phone will be automatically connected to the light. At this time, when you turn on the Bluetooth, it will show that the device Triones-XXXX is connected, which means that the Bluetooth is connected now.
  2. Open the APP and place the phone near the light, it will be connected to the nearest Bluetooth without blocking, after the light is turned off and turned on again.

ONFORU D30BL LED RGB Flood Light 5B

Color Selection Interface:
You could adjust the color and brightness, DIY your favorite color.

ONFORU D30BL LED RGB Flood Light 5C

Music Mode Interface:
You could control the brightness and dynamic changes of the light by playing local music in the phone.

ONFORU D30BL LED RGB Flood Light 5D

Mobile Speaker:
The brightness and color will change with the volume size of the phone or other external voice

ONFORU D30BL LED RGB Flood Light 5E

Dynamic Mode interface:
The dynamic mode of the light (Jump, fade, flash, strobe) and the combination of seven typical colors changes, you can adjust the brightness when changing.

ONFORU D30BL LED RGB Flood Light 5F

Timing Interface:
You can turn on or turn off the light regularly.

ONFORU D30BL LED RGB Flood Light 5G

REMOTE CONTROL OPERATION

With Memory function, the light can start at your last choice of color and mode.

  1. Brightness Adjustment: Press the “ ” or “ ” to either increase or decrease the brightness. There are 8 levels of adjustable brightness.
  2. Stop: Pause color changes in the jump mode, fade mode, flash mode, or automatic mode.
  3. On/Off: Turn on or off the light by pressing “ “
  4. Color Options: Press the colored buttons to select corresponding light.
  5. DIY Mode: After pressing the button DIY1 \ DIY2 \ DIY3, you can DIY different colors by adjusting the RGB brightness through these 6 keys, and these colors are automatically saved. there are 17 variations of colors, and more than 4,800 colors are available for you to choose. 3 kinds of DIY colors can be saved as DIY1 \ DIY2 \ DIY3.
  6. Speed Adjustment: Adjust the speed of color changes in Jump Mode, Fade Mode and Flash Mode; press the button QUICK to speed up and SLOW to slow down. And 30 kinds of different speed are available for you to choose.
  7. Timing: There are 3 regular intervals 3H\6H\12H to set the timer and the light will be off automatically when the time is up.
  8. Auto Mode: Freely switch Jump Mode, Fade Mode, or Flash Mode.
  9. Flash Mode: Make the light flash.
  10. Fade Mode: FADE3 is the mode of three color gradients, and FADE7 is the mode of seven color gradients.
  11. Jump Mode: JUMP3 is the mode of three color jumps, and JUMP7 is the mode of seven color jumps.
  12. Remove the insulation sheet before using the remote control.

Refer to the figure on the right to remove and replace the remote control battery.
Note:

  1. Used batteries/accumulators and lamps should be separated from the equipment.
  2. Users should delete their personal data.
  3. The battery type is button battery CR2025, and the battery composition is lithium . The battery cannot be treated as household waste and needs to be disposed of separately.
COMPONENTS AND STRUCTURE

A (US) 1 m(3.28ft)
H05RN-F 2 x 18AWG
B (UK) 1m(3.28ft)
H05RN-F 2×1.0mm²
C (EU) 1m(3.28ft)
H05RN-F 2×1.0mm²

1. Tempered Glass Lid 2. LED Light Source 3. Lamp Bracket

NOTE

01                              02                          03

01 – Make sure that the distance between the light and the object being lit is more than 1 meter, so as to avoid high temperature caused by short distance.
02 – Safety Class II=This lamp is doubly insulated and may not be wired to a protective conductor.
03 – Lights that are not suitable for covering with thermal insulation materials.

Limitation of Indoor and Outdoor Use

  1. This light is waterproof and dustproof. It is protected against the rain, but it cannot be immersed in water.
  2. The mounting position of this light should be able to bear at least 10 times as heavy as the light.
  3. This light is powered by High Voltage Alternating Current (HVAC). It should be connected to the ground wire and kept away from easy reach.
  4. This light should be used in condition with sound heat dissipation. The working temperature of it should be less than 40°C. Overhigh working temperature will cause serious lumen depression and affect lifespan of the light.
INSTALLATION STEPS

1                           2                                 3

Step 1: According to the spacing (see the “A” part of the picture) of two screw bits on the LED Light bracket, drill two mounting holes.
Step 2: Put the bracket onto the prepared mounting holes and then screw it on.
Step 3: Adjust the beam direction as you like, and then plug into the main socket.
NOTE: Recommended installation height not higher than 5 m (16.4 ft)

OPERATION & MAINTENANCE
  • Prior to cleaning the light, make sure it has been disconnected from the power supply.
  • The unit is not suitable for burglar alarm systems as it is not tamperproof in the manner prescribed for such systems.
  • Never use any chemicals or corrosive substances for cleaning.
DISPOSAL

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner.

Do not dispose of electrical and electronic equipment as domestic waste.

EU countries only:

Under the current European Directive on Waste Electrical and Electronic equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Manufacturer
Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si
Address: qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo qu Shen Zhen, Guang Dong, 518000, CN
support@onforuled.com www.onforuleds.com

ONFORU D30BL LED RGB Flood Light EU Rep MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus | support@onforuled.com

ONFORU D30BL LED RGB Flood Light UK Rep MDH LIGHTING LTD
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom | support@onforuled.com

Made in China

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals