Panasonic DL-EH30SE-W Electric Bidet Seat Household Instruction Manual

Panasonic DL-EH30SE-W Electric Bidet Seat Household Instruction Manual

Safety Cautions

To prevent any personal hazard or property damage, make sure to follow the instructions below.
The hazard or damage caused by misuse can be categorized by the following degrees.

WARNING
Indicates a potential hazardous situation where death or severe injury may be suffered if not avoided.

CAUTION
indicates a potential hazardous situation where mild or moderate injury may be suffered if not avoided.

WARNING

• Do not connect any water pipe other than the pipe for tap water. (Risk of cystitis or dermatitis) (Risk of water leak due to corrosion or attached foreign objects)
• Do not supply power to the product by any external switch. (There is a risk that the temperature limiter will return to error)
• Do not damage the power cord and plug. (Otherwise, electric shock or fire from short circuit may be incurred.)
• Do not plug or unplug the power plug with wet hands. (Otherwise, electric shock my be incurred.)
• Do not place any burning objects, including cigarette, near the product. (Risk of electric shock or fire)
• Make the ground connection. (Risk of electric shock may be incurred in the event of any fault and electrical leakage if not grounded.) →Please consult a professional for the ground connection.
• Plug the power plug all the way in. (If it is not plugged completely, electric shock or fire from heating may be incurred. Do not use a damaged plug or a loose wall socket.)
• Comply with relevant electrical regulations when working on any electric circuit. (Otherwise, fire or electric shock may be incurred.)
• Make sure to perform installation by following the instructions in the Installation Instructions (Otherwise, water leak, fire or electric shock may be incurred.)
• Make sure to use supplied or specified parts during installation. (Otherwise, water leak, fire or electric shock may be incurred.)
• Make sure to follow the range of the wall socket’s and connection apparatus’ ratings. Only use 220-230 V AC power. (Risk of fire due to heating)

CAUTION

• Do not apply any pressure to the body connection, for example, falling. (Otherwise, crack or water leak may be incurred.)
  

• Install water pipes by following the regulations imposed for your place of residence. (Otherwise, water leak may be incurred.)

• When moving or installing the bidet, hold the body with both hands. (If you move it by holding the seat or lid, it may fall off from the body and cause injury.)

Cautions Before Installation

Note

• Do not plug the power plug before the bidet body is installed completely. Otherwise, a malfunction may be incurred.
• When the water remaining inside the body is frozen, move the body to a warm place. Perform installation after the frozen water is thawed out.
• Make sure to use the supplied water inlet hose. Otherwise, a water leak may be incurred.

Tips

• As the product has undergone the water passage test, a small amount of water remaining inside may flow out.
• This is not a malfunction.
• The operating range of water pressure is 49 – 735 kPa｛0.5 – 7.5 kgf/cm2｝.
• Shaking may sometimes result from seat mounts not contacting with the surface of the toilet depending on toilet types.

Required Tools

• Tape measure

• Phillips screwdriver

• Adjustable wrench

• Bucket and rag

Part Names and Accessories

[Accessories] Check if there is any missing or lost part.

No.

| Part name| Qty.| Verification
---|---|---|---
1| Water inlet hose with shunt valve| 1|
2| Gasket set
Thin type: black, 2.5 mm thick ×1 Thick type: black, 4 mm thick ×1| 1| (Included in the bag for  )
3| Quick fastener| 1| (Included in the bag for  )
4| Top-mounted bolt set| 1|
5| Instructions package
Operation Instructions Installation InstructionsConfirmation card of water release outlet position| 1|

WARNING

• Do not use any sealing tape when connecting the shunt valve. (Risk of water leak can result from the sealing tape stuck on a gasket)
• Make sure to use supplied gaskets and quick fastener.
  (Risk of serious water leak if these are ignored or other parts are connected during installation)

Installation Steps

• Installation of Water Inlet Hose on
• Shunt Valve Side
• Installation of electric bidet seat
• Installation of Water Inlet Hose on Body Side
• Commissioning

Installation of Water Inlet Hose on Shunt Valve Side

1. Close the water inlet valve and remove the water inlet pipe.
   

2. Attach the shunt valve on the water inlet hose to the water inlet valve.
   

3. Re-install the water inlet pipe

Installation of electric bidet seat

1. Remove the installed old seat Perform the removal operation by following the Instructions provided by the purchased toilet.
   

2. Remove the body mounting plate. Press the body assembly / disassembly button all the way in and remove the body mounting plate.
   
   (Pull out along the direction of arrows alternatively.)

3. Install the body mounting plate.

4. The spacing for installing the bolts of the body mounting plate can be adjusted between 130 – 215 mm.
   

5. Fit the metal mounting plate to the top-mounted bolt and screw in the nut. (Fig. 2) (This nut is applicable to toilet with the bore diameter of 12 – 17 mm . For other bore diameters, consult our after-sales service for installation.)

6. For preliminary positioning, secure the top-mounted bolt to the body mounting plate. (Same on both sides)

7. With a tape measure, measure the length of A. (Fig. 3)

8. Align the center line of the top-mounted bolt with the reference scale line matching A on the body mounting plate for preliminary positioning. (Fig. 4)
   

9. Adjust the position of the body mounting plate and ensure B 80 mm. Then, install the body mounting plate to the toilet.(Fig. 5)
   

10. Install the body.

11. Align the protrusion in the center on the back side of the body with the one in the center of the body mounting plate.

12. Lift up the rear part of the body slightly and slide it towards the body mounting plate until a “click” is heard.

  * Do not secure the power cord between the body and toilet.  

  * When the rear part of the lid contacts the water tank of the toilet, or the lifted seat falls down easily. Move the body mounting plate forwards slightly and secure it. Install the body again.  

• Do not place the nozzle compartment at the body base on the surface of the toilet.
• Make sure the front seat mount is placed on the surface of the toilet.
• Make sure to install the body mounting plate with B 80 mm. Otherwise, the body may be tilted or a water leak may occur.
• Once the body is installed, lift it up gently to check if it isinstalled securely.
• As this product is design with a detachable structure to enable the body to be removed from the toilet, it may sometimes feel slightly shaky. This is not a malfunction.

Installation of Water Inlet Hose on Body Side

Caution:
Serious water leaks may occur if the water inlet hose is installed improperly

Connect to the body

1. As illustrated, insert the O-ring side of the water inlet hose straight into the body connection port. (If not inserted straight, the O-ring may be damaged.)

2. As illustrated, insert the quick fastener all the way into the connection correctly until a “click” is heard.

3. Tighten the claw securely.
   

4. Bend the hole end downwards.

5. Bend the claw end towards the hole end and tighten it. (Until a “click” is heard)

6. With the water inlet hose held in your hands, turn the quick fastener gently. The turning operation should be smooth. (If it is not smooth, it indicates the installation is done improperly.)

Make sure to

• Check if the quick fastener is secured firmly.
• Pull the water inlet hose gently to check if it will not separated from the body.

**Open the water inlet valve.

**

• Once all ports are connected and verified, open the water inlet valve.

During installation, the body connection can be turned.

Tips

• When the bathroom is confined and it is difficult to install the water inlet hose after the bidet body is installed, you can attach the water inlet hose to the body first, and then install the body to the toilet.

Commissioning

Before Commissioning…… Check if the water inlet valve is opened. (Volume adjustment will be affected if it is not opened.) Check if there is any water leaked from the connection.

1. Cover with a plastic film or similar device. (Between the seat and toilet)

2. Check if the power plug is plugged. (The Power indicator is on.)

3. Press and hold the Electrical Leakage Test button for 2 seconds or longer

   • The electrical leakage detection function is activated and power is cut off. (The Electrical Leakage indicator is on and the Power indicator is off.)

4. Unplug the power plug.

   • Check if the Electrical Leakage indicator is off.

5. After 5 seconds, plug the power plug.
   

   • The Power indicator will flash for approximately 10 seconds before remaining on.
   • Check if the water temperature is set to “Off”.
   • When the Electrical Leakage indicator flashes, unplug the power plug immediately and contact your dealer or one of Panasonic-operated service centers.
   • If you touch a closed seat (the Occupancy indicator is on and deodorization operate and unintentionally press the Rear Showering / Front Showering button, water will come out and spray on yourself.

6. Press

   • The nozzle extends and the warm water tank of the body begins to pump in water. After approximately 1 minute, water will flow out from the nozzle downwards. If no water flows out, check if the main water valve is opened or the water inlet valve isn’t opened sufficiently.
     About idle running in the warm water tank

   • When carrying out Step , the warm water tank is running idle if the “High”, “Mid” and “Low” Water Temperature indicators all flash. This is not a malfunction.

   • Open the main water valve and water inlet valve. Start commissioning from Step again. (The Water Temperature indicator is off.)
     About releasing water

   • The water flowing out next to the nozzle (water release outlet) is the one released for pressure adjustment. This is not a malfunction. If the water release outlet is placed on the surface of the toilet, water may not flow into the toilet. At this time, install the body sightly forward.

7. Press

   • The nozzle retracts

8. Press and hold the rear left portion of the seat. (The Occupancy indicator is on.) Meanwhile, press

   • Deodorization starts. (with motor sound)
   • The nozzle starts self-cleaning. After approximately 5 – 8 seconds, cleaning water will be sprayed. (If the Occupancy Switch is not enabled, no water will be sprayed.)
   • Check if cleaning water is sprayed normally with the plastic film.

9. Press

   • Once the nozzle retracts, water for nozzle self-cleaning will come out.

10. Remove the plastic film.

11. Press and hold the rear left portion of the seat.(The Occupancy indicator is on.) Meanwhile,
    Press , confirm warm air function , then press

12. Press to set the temperature. After 5 -12 minutes, sit at the seat to check the seat and water temperature.

    • It takes approximately 5 – 12 minutes for the temperature of the seat and warm water to stabilize. (Depending on ambient temperature and the temperature of tap water.)

After showering stops, droplets will fall from around the nozzle. These are the water resulted from thermal expansion of the warm water tank or water remaining in the nozzle. This is not a malfunction. (Approximately 7 – 8 minutes after showering)

The Occupancy Switch is enabled when the seat is occupied

The back mount of the seat and the front leg are floating It is normal. If this gap is not present, seating detection will not be detected.

Troubleshooting

Caution After Installation

• When the product is likely not to be used for more than 1 week, drain it. (Refer to “When Not Used for A Long Time “ in the Operating Instructions.)

Service information

Malaysia
Panasonic Malaysia
Lot 10, Street 13/2, 46200 Petaling Jaya, Selangor Darul Ehsan.
‘+603-79537600
E-mail: ccc@my.panasonic.com
© Panasonic Corporation 2022
Printed in China

References

• Panasonic North America | Create Today, Enrich Tomorrow

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>