Fishbone FB22341 Barracuda Bull Bar Installation Guide

Fishbone FB22341 Barracuda Bull Bar

Product Information

The FB22341, FB22342, FB22343, and FB22344 are front bumpers and  accessories designed for use on 2007-Current JK/JL Wrangler &  JT Gladiator vehicles.
These products are manufactured by Barracudaand are compatible with the mentioned vehicle models.

The following items are included in each product:

FB22341:

• 6 x M12 Hex Bolt
• 8 x M10 Hex Bolt
• 12 x M12 Flat Washer
• 16 x M10 Flat Washer
• 6 x M12 Hex Nut
• 6 x M12 Lock Washer
• 8 x M10 Lock Washer
• 8 x M10 Hex Nut

FB22342 & FB22343:

• 4 x M12 Hex Bolt
• 8 x M10 Hex Bolt
• 8 x M12 Flat Washer
• 16 x M10 Flat Washer
• 4 x M12 Lock Washer
• 8 x M10 Lock Washer
• 4 x M12 Hex Nut
• 8 x M10 Hex Nut
• 2 x D-Rings
• Foam

FB22344:

• 8 x M10 Hex Bolt
• 8 x M10 Flat Washer
• 8 x M10 Lock Washer
• 8 x M10 Hex Nut
• 2 x D-Rings

Product Usage Instructions

REMOVE EXISTING BUMPER

• Begin by removing your existing bumper and any accessories that   may obstruct the installation. You can find a video tutorial on how to uninstall your JK/JL/JT factory bumper on the FishboneOffroad YouTube channel.

ASSEMBLE THE BUMPER

• Using a 19mm socket, install the fairlead onto the top of the  bumper using 2 of the included M12 bolts, washers, and nuts. Place the bar up to the bumper and secure only the top plate using 4 M12 bolts, 8 washers, and nuts with a 19mm socket. If you havepurchased the Bull Bar or Stinger, apply the foam padding to the inside of the mounting brackets.

INSTALL BUMPER

• With the help of a friend, hold the bumper up to the frame and  center it on the bolt holes. If you own the base model or any bar, secure it to the frame using 8 M10 bolts, 16 washers, and nuts with a 17mm socket and wrench. Install your D-Rings after securing the bumper.
• If you have purchased the D-Ring set, hold the bumper in place with the help of a friend while aligning the D-Ring caps with the  bolt and frame holes. Secure the bumper to the frame using 8 M10 bolts, 16 washers, and nuts with a 17mm socket and wrench. Install your D-Rings after securing the bumper.

MODELS

REQUIRED TOOLS

• 19mm Socket
• 17mm Wrench
• 17mm Socket

Help of a Friend

INSTALLATION INSTRUCTION

1. REMOVE EXISTING BUMPER
   • Begin removing your existing bumper and any accessory that may get in the way. We show how to uninstall your JK/JL/JT factory bumper over on our YouTube channel: www.FishboneOffroad.TV.
2. ASSEMBLE THE BUMPER
   • With a 19mm socket, install the fairlead onto the top of the bumper with 2 of the included M12 bolts, washers, and nuts.
   • If you purchased the Bull Bar or Stinger, apply the foam padding to the inside of the mounting brackets.
   • Place the bar up to the bumper and secure only the top plate with 4 M12 bolts, 8 washers, and nuts with a 19mm socket.
3. INSTALL BUMPER
   • With the help of a friend, hold the bumper up to the frame and center it on the bolt holes. If you own the base model or any bar, secure it to the frame with 8 M10 bolts, 16 washers, and nuts with a 17mm socket and wrench.
   • Followed by installing your D-Rings.
   • If you purchased the D-Ring set, with the help of a friend, hold the bumper into place while you align the D-Ring caps with the bolt and frame holes.
   • With 8 M10 bolts, 16 washers, and nuts and a 17mm socket and wrench, secure the bumper to the frame. Followed by installing your D-Rings.

550 W. PINE LAKE RD., SUITE 2, NORTH LIMA, OHIO 44452 330.423.6446WWW.FISHBONEOFFROAD.COM

References

• Fishbone Offroad - YouTube
• Fishbone Offroad - YouTube

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>